TIA-102 AABG-2009 Project 25 Conventional Control Messages《项目25 传统控制讯息》.pdf

《TIA-102 AABG-2009 Project 25 Conventional Control Messages《项目25 传统控制讯息》.pdf》由会员分享，可在线阅读，更多相关《TIA-102 AABG-2009 Project 25 Conventional Control Messages《项目25 传统控制讯息》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、 TIA-102.AABG April 2009 Project 25 Conventional Control Messages NOTICE TIA Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchangeability and improvement of products, and a

2、ssisting the purchaser in selecting and obtaining with minimum delay the proper product for their particular need. The existence of such Standards and Publications shall not in any respect preclude any member or non-member of TIA from manufacturing or selling products not conforming to such Standard

3、s and Publications. Neither shall the existence of such Standards and Publications preclude their voluntary use by Non-TIA members, either domestically or internationally. Standards and Publications are adopted by TIA in accordance with the American National Standards Institute (ANSI) patent policy.

4、 By such action, TIA does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the Standard or Publication. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is t

5、he responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of regulatory limitations before its use. (From Standards Proposal No. 3-604-UGR, formulated under the cognizance of the TIA, TR-8 Mobile and Personal Private Radio

6、Standards. TR-8.10 Subcommittee onTrunking and Convention Control). Published by TELECOMMUNICATIONS INDUSTRY ASSOCIATION Standards and Technology Department 2500 Wilson Boulevard Arlington, VA 22201 U.S.A. PRICE: Please refer to current Catalog of TIA TELECOMMUNICATIONS INDUSTRY ASSOCIATION STANDARD

7、S AND ENGINEERING PUBLICATIONS or call IHS USA and Canada (1-800-525-7052 ) International (303-790-0600) or search online at http:/www.tiaonline.org/standards/catalog/ All rights reserved Printed in U.S.A. NOTICE OF COPYRIGHT This document is copyrighted by the TIA. Reproduction of these documents e

8、ither in hard copy or soft copy (including posting on the web) is prohibited without copyright permission. For copyright permission to reproduce portions of this document, please contact TIA Standards Department or go to the TIA website (www.tiaonline.org) for details on how to request permission. D

9、etails are located at: http:/www.tiaonline.org/standards/catalog/info.cfm#copyright OR Telecommunications Industry Association Standards (b) there is no assurance that the Document will be approved by any Committee of TIA or any other body in its present or any other form; (c) the Document may be am

10、ended, modified or changed in the standards development or any editing process. The use or practice of contents of this Document may involve the use of intellectual property rights (“IPR”), including pending or issued patents, or copyrights, owned by one or more parties. TIA makes no search or inves

11、tigation for IPR. When IPR consisting of patents and published pending patent applications are claimed and called to TIAs attention, a statement from the holder thereof is requested, all in accordance with the Manual. TIA takes no position with reference to, and disclaims any obligation to investiga

12、te or inquire into, the scope or validity of any claims of IPR. TIA will neither be a party to discussions of any licensing terms or conditions, which are instead left to the parties involved, nor will TIA opine or judge whether proposed licensing terms or conditions are reasonable or non-discrimina

13、tory. TIA does not warrant or represent that procedures or practices suggested or provided in the Manual have been complied with as respects the Document or its contents. If the Document contains one or more Normative References to a document published by another organization (“other SSO”) engaged i

14、n the formulation, development or publication of standards (whether designated as a standard, specification, recommendation or otherwise), whether such reference consists of mandatory, alternate or optional elements (as defined in the TIA Engineering Manual, 4thedition) then (i) TIA disclaims any du

15、ty or obligation to search or investigate the records of any other SSO for IPR or letters of assurance relating to any such Normative Reference; (ii) TIAs policy of encouragement of voluntary disclosure (see Engineering Manual Section 6.5.1) of Essential Patent(s) and published pending patent applic

16、ations shall apply; and (iii) Information as to claims of IPR in the records or publications of the other SSO shall not constitute identification to TIA of a claim of Essential Patent(s) or published pending patent applications. TIA does not enforce or monitor compliance with the contents of the Doc

17、ument. TIA does not certify, inspect, test or otherwise investigate products, designs or services or any claims of compliance with the contents of the Document. ALL WARRANTIES, EXPRESS OR IMPLIED, ARE DISCLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRANTIES CONCERNING THE ACCURACY OF THE CON

18、TENTS, ITS FITNESS OR APPROPRIATENESS FOR A PARTICULAR PURPOSE OR USE, ITS MERCHANTABILITY AND ITS NONINFRINGEMENT OF ANY THIRD PARTYS INTELLECTUAL PROPERTY RIGHTS. TIA EXPRESSLY DISCLAIMS ANY AND ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND MAKES NO REPRESENTATIONS OR WARRANTIES REGARD

19、ING THE CONTENTS COMPLIANCE WITH ANY APPLICABLE STATUTE, RULE OR REGULATION, OR THE SAFETY OR HEALTH EFFECTS OF THE CONTENTS OR ANY PRODUCT OR SERVICE REFERRED TO IN THE DOCUMENT OR PRODUCED OR RENDERED TO COMPLY WITH THE CONTENTS. TIA SHALL NOT BE LIABLE FOR ANY AND ALL DAMAGES, DIRECT OR INDIRECT,

20、 ARISING FROM OR RELATING TO ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAGES FOR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED UPON BREACH OF CONTRACT, BREACH OF

21、WARRANTY, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE FOREGOING NEGATION OF DAMAGES IS A FUNDAMENTAL ELEMENT OF THE USE OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA WITHOUT SUCH LIMITATIONS. TSB-102.

22、AABG ii Foreword (This foreword is not part of this standard.) This document has been submitted to APCO/NASTD/FED by the Telecommunications Industry Association (TIA), as provided for in a Memorandum of Understanding (MOU) dated December 1993. That MOU provides that APCO/NASTD/FED will devise a Comm

23、on System Standard for digital public safety communications (the Standard), and that TIA shall provide technical assistance in the development of documentation for the Standard. This document has been developed with inputs from the APCO/TIA Project 25 Interface Committee (APIC), the APIC Systems Tas

24、k Group, and TIA Industry members. This document is being published because it is felt that there is an urgent need for technical information on the emerging digital techniques for Land Mobile Radio Service. This document describes enhancements to the conventional messages for meeting the Project 25

25、 requirements. These definitions are necessary to insure interoperability of conventional radio units. As other documents describing the conventional protocol are developed, this document will be subject to change, additional messages may be needed. Some efforts have been made to ensure accuracy. Th

26、is document is a standard. It presents an overview of conventional messages which was recommended by TIA to APCO/NASTD/FED as being suitable for use as part of their standard for a digital public safety radio system (Project 25). TIA-102.AABG iii Table of Contents 1. Introduction .1 1.1 Scope.1 1.2

27、Overview1 1.3 References 1 1.3.1 Normative References2 1.3.2 Informative References.2 1.4 Definitions2 1.5 Acronyms.2 1.6 Revision History.3 2 Supplementary Data Message Specifications 4 TIA-102.AABG 1 1. Introduction APCO Project 25 applies to both conventional and trunked systems. The distinction

28、between conventional and trunking systems may be that trunking systems include a centralized controlling device which is used to assign channels to subscribers as service is demanded. This controlling device is absent in a conventional system. A large set of useful functions are defined for trunking

29、 systems, including but not limited to the functions necessary for subscribers to request service and for the controller to grant service. Trunking also defines functions which may be applied to conventional systems, such as an Emergency Alarm. This document is intended to define the messages for th

30、ose functions that are defined for trunking which can also be applied to conventional systems. These control functions are referred to as Supplementary Data functions in this document. 1.1 Scope This document defines the message formats for the conventional supplementary data functions. These supple

31、mentary data messages are extensions to the basic Common Air Interface. Conventional systems for APCO Project 25 are defined to be any non-trunked system which conforms to the standards and specifications of 102A or its subordinate documents, where a trunked system is defined to include a centralize

32、d controller that assigns requests for service by subscribers to specific radio channels. Conventional systems therefore do not have a controller which assigns radio channels in the same sense as defined in 102AABC-B. 1.2 Overview The following supplementary data messages of trunking systems are use

33、ful in some conventional systems. Those control messages for services that are listed as standard options in 102A are labeled accordingly. Note that Radio Detach, not found in 102A but defined in 102AABC-B and 102AABD-A, is not a conventional feature and is not listed below. Emergency Alarm - Not sp

34、ecifically mentioned Call Alert - Standard Option Radio Check - Not specifically mentioned Radio Inhibit and Radio Uninhibit - Standard Option Status Update and Status Request - Not specifically mentioned Message - Standard Option Telephone Interconnect Dialing - Standard Option Radio Unit Monitor -

35、 Standard Option These supplementary data messages are defined in this document for conventional systems. 1.3 References The following documents contain provisions which, through reference in this text, constitute provisions of this standard. At the time of publication, the editions indicated were v

36、alid. All standards are subject to revision, and parties to agreements based on this standard are encouraged to investigate the possibility of applying the most recent editions of the standards indicated below. ANSI and TIA maintain registers of currently valid national standards published by them.

37、TIA-102.AABG 2 1.3.1 Normative References 102AABC-B Trunking Control Channel Messages, TIA-102.AABC-B, January 2005. 102BAAA-A Recommended Common Air Interface, TIA-102.BAAA-A, September 2003. 102AABD-A Trunking Procedures, TIA-102.AABD-A, December, 2008. 102BADA Telephone Interconnect Requirements

38、and Definitions (Voice Service), TIA-102.BADA, March 2000. 102BADA-1 Addendum 1 of Telephone Interconnect Requirements and Definitions (Voice Service), TIA-102.BADA-1, April 2004. 102BAAD Common Air Interface Operational Description for Conventional Channels, TIA-102.BAAD, December 2003. 102AABF-A L

39、ink Control Word Formats and Messages, TIA-102.BAAC-A, December 2003. 1.3.2 Informative References 102A Project 25 System and Standards Definition, TSB-102.A, November 1995. 1.4 Definitions Console: This term is used to denote a fixed console device. .A console is wireline device, located inside an

40、RFSS or attached to the RFSS via the P25 Console Sub-System Interface. Mobile: This term is used to denote a mobile radio device. A Mobile is portable and can roam. A mobile can be a mobile console which has additional capabilities beyond a normal mobile such as being able to originate the Remote Mo

41、nitor command. A mobile SU is the same as a mobile. SU: A P25 Subscriber Unit. An SU can be a fixed or portable unit. A Subscriber Unit is identified by an SUID. A console is typically considered a fixed P25 Subscriber Unit, although some may be mobile. A Mobile is considered a P25 portable unit. UI

42、D: A Unit ID. A conventional mobile radio has one UID for a given channel. A conventional radio may utilize the same or different UID on each of the channels that it operates. A conventional radios UIDs are pre-configured; they are not assigned by the system. A console also utilizes UIDs in the same

43、 manner as a mobile. 1.5 Acronyms ACK_RSP_FNE = Acknowledge response-FNE (to SU or to FNE) AIV = Additional Information Valid CAI = Common Air Interface CAN_SRV_REQ = Cancel Service Request DENY_RSP = Deny Response EMRG_ALRM_REQ = Emergency alarm request FNE = Fixed Network Equipment LC_CALL_TERM_CA

44、N = Call Termination/Cancellation QUE_RSP = Queue Response RAD_MON_CMD = Radio unit Monitor Command RFSS = RF Sub System TIA-102.AABG 3 STS_Q = Status Query STS_Q_REQ = Status Query request STS_Q_RSP = Status Query response STS_UPDT = Status update STS_UPDT_REQ = Status update request SU = Subscribe

45、r Unit TEL_INT_ANS_RSP = Telephone Interconnect Answer Response TEL_INT_ANS_REQ = Telephone Interconnect Answer Request TELE_INT_DIAL_REQ = Telephone interconnect voice service request TELE_INT_PSTN_REQ = Telephone Interconnect Request Implicit Dialing TSBK = Trunking Signaling Block 1.6 Revision Hi

46、story March 10, 1995, version 0.0, initialized the definitions of conventional features. June 30, 1995, substitute control messages for features. January 24, 1996, updated section numbers for revised reference 2 and also added addressing information. June 4, 1996, updated from letter ballot comments

47、. July 2007, Modified as part of the Compliance Assessment program. Updated to a normative TIA document and brought in the content of TSB-102.AABG-1. TIA-102.AABG 4 2 Supplementary Data Message Specifications Mobile SU 1Wireless Console SU 2Fixed Station 1RFSS 1Fixed Station 3Wireline Console SU 4Wi

48、reline Console SU 6Wireline Console SU 3RFSS 2Wireline Console SU 7Mobile SU 8Wireless Console SU 9Mobile SU 5Fixed Station 2Figure 2-1 Example Conventional System Diagram Conventional supplementary data utilizes the Trunked Signaling Block (TSBK) exactly as defined in TIA-102.AABC Trunking Control

49、Channel Messages 102AABC-B. To avoid duplicating the definitions, this section calls out the sections in 102AABC-B which define the messages. Some messages have two identical CAI formats defined whose names depend on whether the message originated from a mobile device or from the RFSS. Messages originating at an RFSS do so because of console action or because they came from another RFSS. For instance, in Figure 2-1, A CALL_ALRT_REQ originated by SU 1 to Fixed Sta