TIA-1014-2004 Removable User Identity Module Conformance Testing for Spread Spectrum Systems《扩频系统可移动用户识别模块一致性测试》.pdf

《TIA-1014-2004 Removable User Identity Module Conformance Testing for Spread Spectrum Systems《扩频系统可移动用户识别模块一致性测试》.pdf》由会员分享，可在线阅读，更多相关《TIA-1014-2004 Removable User Identity Module Conformance Testing for Spread Spectrum Systems《扩频系统可移动用户识别模块一致性测试》.pdf（140页珍藏版）》请在麦多课文档分享上搜索。

1、 TIA DOCUMENT Removable User Identity Module Conformance Testing for Spread Spectrum Systems TIA-1014 MARCH 2004 TELECOMMUNICATIONS INDUSTRY ASSOCIATION The Telecommunications Industry Association represents the communications sector of Copyright Telecommunications Industry Association Provided by I

2、HS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NOTICE TIA Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interchange

3、ability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for their particular need. The existence of such Publications shall not in any respect preclude any member or non-member of TIA from manufacturing or selling products not

4、 conforming to such Publications. Neither shall the existence of such Documents preclude their voluntary use by non-TIA members, either domestically or internationally. TIA DOCUMENTS TIA Documents contain information deemed to be of technical value to the industry, and are published at the request o

5、f the originating Committee without necessarily following the rigorous public review and resolution of comments which is a procedural part of the development of a American National Standard (ANS). Further details of the development process are available in the TIA Engineering Manual, located at http

6、:/www.tiaonline.org/standards/sfg/engineering_manual.cfm TIA Documents shall be reviewed on a five year cycle by the formulating Committee and a decision made on whether to reaffirm, revise, withdraw, or proceed to develop an American National Standard on this subject. Suggestions for revision shoul

7、d be directed to: Standards Specification of the 3 Subscriber Identity Module - Mobile Equipment (SIM - ME) interface“. 4 3. ISO/IEC 7816-1 (1987): “Identification cards - Integrated circuit(s) cards with contacts, 5 Part 1: Physical characteristics“. 6 4. ISO/IEC 7816-2 (1988): “Identification card

8、s - Integrated circuit(s) cards with contacts, 7 Part 1: Dimensions and locations of the contacts“. 8 5. ISO/IEC 7816-3 (1989): “Identification cards - Integrated circuit(s) cards with contacts, 9 Part 1: Electronic signals and transmission protocols“. 10 6. ISO/IEC 7811-1 (1995): “Identification ca

9、rds - Recording technique - Part 1: 11 Embossing“. 12 7. ISO/IEC 7811-3 (1995): “Identification cards - Recording technique - Part 3: Location of 13 embossed characters on ID-1 cards“. 14 8. GSM 11.12: “Digital cellular telecommunications system (Phase 2); Specification of the 15 3 Volt Subscriber I

10、dentity Module - Mobile Equipment (SIM - ME) interface“. 16 9. GSM 11.18: “Digital cellular telecommunications system (Phase 2+); Specification of the 17 1.8 Volt Subscriber Identity Module - Mobile Equipment (SIM - ME) interface“. 18 10. GSM 11.17: “Digital cellular telecommunications system (Phase

11、 2+); Subscriber Identity 19 Module (SIM) conformance test specification“. 20 11. Interface Specification for Common Cryptographic Algorithms, Rev D.1 2000. 21 Contact the Telecommunications Industry Association, Arlington, VA. 22 12. Interface Specification for Enhanced Cryptographic Algorithms, Re

12、v B, 2002. 23 Contact the Telecommunications Industry Association, Arlington, VA. 24 13. TIA/EIA-683-C: “Over-the-Air Service Provisioning of Mobile Stations in Spread 25 Spectrum Systems”. 26 Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo re

13、production or networking permitted without license from IHS-,-,-TIA-1014 xx 1 No text. 2 Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIA-1014 1-1 1 GENERAL 1 1.1 Definitions

14、 2 For the purposes of the present document, the following terms and definitions apply in 3 addition to the terms defined in 1. 4 Implementation Conformance Statement (ICS): A statement made by the supplier of an 5 implementation or system claimed to conform to a given specification, stating which 6

15、 capabilities have been implemented. The ICS can take several forms: protocol ICS, profile 7 ICS, profile specific ICS, information object ICS, etc. 8 1.2 Abbreviations 9 For the purposes of the present document, the following abbreviations apply: 10 3GPP2 3rd Generation Partnership Project 2 11 CRn

16、 Conformance Requirement n 12 DF Dedicated File 13 ICS Implementation Conformance Statement 14 IUT Implementation Under Test 15 ME Mobile Equipment 16 MF Master File 17 MS Mobile Station 18 R-UIM Removable User Identity Module 19 SIM Subscriber Identity Module 20 SS System Simulator 21 TS Test Speci

17、fication 22 Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIA-1014 1-2 1 No text.2 Copyright Telecommunications Industry Association Provided by IHS under license with EIANot

18、for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIA-1014 2-1 2 R-UIM TEST ENVIRONMENT 1 The test environment shall comply with the requirements specified in Section 4, “Test 2 Environment” of 10. 3 Copyright Telecommunications Industry Association Provided by IHS under

19、 license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIA-1014 2-2 1 No text.2 Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIA-

20、1014 3-1 3 R-UIM TEST PROCEDURE 1 This section details each of the tests in each of the following categories: 2 - Physical characteristics 3 - Electronic signals and transmission protocols 4 - Logical model 5 - Security services and facilities 6 - Functions 7 - Commands 8 - Contents of the elementar

21、y files 9 3.1 Physical Characteristics 10 The R-UIM shall conform to the requirements defined in Section 9.1 “Physical 11 characteristics” of 10. 12 3.2 Signals and Transmission Protocols 13 The tests in this section ensure that the IUT conforms to the electrical specification for 14 each of the con

22、tacts and follow the correct protocol. 15 3.2.1 Supply Voltage Vcc (contact C1) 16 The R-UIM shall conform to the requirements related to 3V and 5V operation specified in 17 Section 6.2.1 of 10. 18 3.2.2 Reset RST (contact C2) 19 The R-UIM shall conform to the requirements related to 3V and 5V opera

23、tion specified in 20 Section 6.2.2 of 10. 21 3.2.3 Clock CLK (contact C3) 22 The R-UIM shall conform to the requirements related to 3V and 5V operation specified in 23 Section 6.2.3 of 10. 24 3.2.4 I/O (Contact C7) 25 The R-UIM shall conform to the requirements related to 3V and 5V operation specifi

24、ed in 26 Section 6.2.4 of 10. 27 3.2.5 States 28 The R-UIM shall conform to the requirements specified in Section 6.2.5 of 10. 29 3.2.6 Answer To Reset (ATR) 30 The R-UIM shall conform to the requirements specified in Section 6.2.6 of 10. 31 3.2.7 Major Capabilities 32 The R-UIM shall conform to the

25、 requirements specified in Section 6.2.7 of 10. 33 Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIA-1014 3-2 3.3 Logical Model 1 The tests in this section ensure that the IUT

26、 is tested against the specification of the R-2 UIMs logical structure, secret codes, and file structures. 3 3.3.1 File Identifier 4 3.3.1.1 File-type Identification 5 3.3.1.1.1 Definition and Applicability 6 A file identifier is used to address or identify each specific file. 7 3.3.1.1.2 Conformanc

27、e Requirement 8 CR1 For CDMA, the Master File shall be coded as 3F 00. 9 CR2 For CDMA, file type 7F shall be used to identify Dedicated Files. 10 CR3 For CDMA, file type 2F shall be used to identify Elementary Files under the 11 Master File. 12 CR4 For CDMA, file type 6F shall be used to identify El

28、ementary Files under a 13 Dedicated File with file type 7F. 14 3.3.1.1.3 Test Purpose 15 Verify that the R-UIM conforms to the above requirements. 16 3.3.1.1.4 Method of Test 17 3.3.1.1.4.1 Initial Conditions 18 1) The R-UIM is connected to an ME Simulator. 19 3.3.1.1.4.2 Procedure 20 a) The ME Simu

29、lator resets the R-UIM. 21 b) For each file in figure 7 of 2, section 10.4, the ME Simulator sends SELECT 22 commands to the R-UIM to select the file ID and, if selected successfully, the ME 23 Simulator sends a GET RESPONSE command to the R-UIM. 24 After each successful SELECT and GET RESPONSE, byt

30、e 7 of the response data shall 25 conform to the following table: 26 File ID Type of File 27 3F 00 01 28 7F XX 02 29 2F XX 04 30 6F XX 04 31 Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-