TIA-1013-2003 Mobile Equipment (ME) Conformance Testing for cdma2000 Spread Spectrum Standards《CDMA2000扩频系统的移动设备一致性测试》.pdf

《TIA-1013-2003 Mobile Equipment (ME) Conformance Testing for cdma2000 Spread Spectrum Standards《CDMA2000扩频系统的移动设备一致性测试》.pdf》由会员分享，可在线阅读，更多相关《TIA-1013-2003 Mobile Equipment (ME) Conformance Testing for cdma2000 Spread Spectrum Standards《CDMA2000扩频系统的移动设备一致性测试》.pdf（48页珍藏版）》请在麦多课文档分享上搜索。

1、 TIA DOCUMENT Mobile Equipment (ME) Conformance Testing for cdma2000 Spread Spectrum Standards TIA-1013 DECEMBER 2003 TELECOMMUNICATIONS INDUSTRY ASSOCIATION The Telecommunications Industry Association represents the communications sector of Copyright Telecommunications Industry Association Provided

2、 by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-NOTICE TIA Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstandings between manufacturers and purchasers, facilitating interc

3、hangeability and improvement of products, and assisting the purchaser in selecting and obtaining with minimum delay the proper product for their particular need. The existence of such Publications shall not in any respect preclude any member or non-member of TIA from manufacturing or selling product

4、s not conforming to such Publications. Neither shall the existence of such Documents preclude their voluntary use by non-TIA members, either domestically or internationally. TIA DOCUMENTS TIA Documents contain information deemed to be of technical value to the industry, and are published at the requ

5、est of the originating Committee without necessarily following the rigorous public review and resolution of comments which is a procedural part of the development of a American National Standard (ANS). Further details of the development process are available in the TIA Engineering Manual, located at

6、 http:/www.tiaonline.org/standards/sfg/engineering_manual.cfm TIA Documents shall be reviewed on a five year cycle by the formulating Committee and a decision made on whether to reaffirm, revise, withdraw, or proceed to develop an American National Standard on this subject. Suggestions for revision

7、should be directed to: Standards 4 Specification of the Subscriber Identity Module - Mobile Equipment (SIM - 5 ME) interface“. 6 3 ISO/IEC 7816-1 (1987): “Identification cards - Integrated circuit(s) cards 7 with contacts, Part 1: Physical characteristics“. 8 4 ISO/IEC 7816-2 (1988): “Identification

8、 cards - Integrated circuit(s) cards 9 with contacts, Part 1: Dimensions and locations of the contacts“. 10 5 ISO/IEC 7816-3 (1989): “Identification cards - Integrated circuit(s) cards 11 with contacts, Part 1: Electronic signals and transmission protocols.“ 12 6 ISO/IEC 7811-1 (1995): “Identificati

9、on cards - Recording technique - Part 1: 13 Embossing“ 14 7 ISO/IEC 7811-3 (1995): “Identification cards - Recording technique - Part 3: 15 Location of embossed characters on ID-1 cards“ 16 8 ETSI ETS 300 641 (GSM 11.12): “Digital cellular telecommunications system 17 (Phase 2); Specification of the

10、 3 Volt Subscriber Identity Module - Mobile 18 Equipment (SIM - ME) interface“. 19 9 ETSI TS 131 101: “Digital cellular telecommunications system (Phase 2+); 20 Specification of the 1.8 Volt Subscriber Identity Module - Mobile Equipment 21 (SIM - ME) interface“. 22 10 ETSI TS 151 010-1: “Mobile Stat

11、ion (MS) conformance specification; Part 1: 23 Conformance specification”. 24 11 TIA-898: “Signaling Conformance Tests for cdma2000Spread Spectrum 25 Systems”1. 26 1cdma2000is the trademark for the technical nomenclature for certain specifications and standards of the Organizational Partners (OPs) o

12、f 3GPP2. Geographically (and as of the date of publication), cdma2000 is a registered trademark of the Telecommunications Industry Association (TIA-USA) in the United States. Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or netw

13、orking permitted without license from IHS-,-,-TIA-1013 2-2No text. 1 Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIA-1013 3-13 DEFINITIONS AND ABBREVIATIONS 1 3.1 Definition

14、s 2 For the purposes of the present document, the following terms and definitions apply in 3 addition to the terms defined in 1: 4 Implementation Conformance Statement (ICS): A statement made by the supplier of an 5 implementation or a system claimed to conform to a given specification, stating whic

15、h 6 capabilities have been implemented. The ICS can take several forms: protocol ICS, profile 7 ICS, profile specific ICS, information object ICS, etc. 8 3.2 Abbreviations 9 For the purposes of the present document, the following abbreviations apply: 10 3GPP2 3rd Generation Partnership Project 2 11

16、CHV1 Card Holder Verification 1 12 CHV2 Card Holder Verification 2 13 CRn Conformance Requirement n 14 DF Directory File 15 FT Fixed Termination 16 ICS Implementation Conformance Statement 17 IUT Implementation Under Test 18 ME Mobile Equipment 19 MF Master File 20 MS Mobile Station 21 PIN Personal

17、Identity Number 22 PIN2 Personal Identity Number 2 23 PRL Preferred Roaming List 24 PUK PIN Unblocking Key 25 PUK2 PIN2 Unblocking Key 26 R-UIM Removable User Identity Module 27 SIM Subscriber Identity Module 28 SS System Simulator 29 TS Test Specification 30 Copyright Telecommunications Industry As

18、sociation Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIA-1013 3-2No text. 1 Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted with

19、out license from IHS-,-,-TIA-1013 4-14 ME TEST ENVIRONMENT 1 The test environment shall comply with the requirements specified in Clause 4, “Physical 2 Characteristics” and Clause 5, “Electronic Signals and Transmission Protocols” of 2. 3 Copyright Telecommunications Industry Association Provided by

20、 IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIA-1013 4-2No text. 1 Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-

21、,-,-TIA-1013 5-15 TESTING OF THE ME 1 The following sequence of tests confirms: 2 1) the correct interpretation of data read from the R-UIM (Removable-User 3 Identification Module) by the ME; 4 2) the correct writing of data to the R-UIM by the ME; 5 3) the initiation of appropriate procedures by th

22、e ME; 6 4) low level protocols; 7 5) electrical characteristics; 8 6) physical characteristics. 9 All tests apply to MEs conforming to 1 using either ID-1 or Plug-in R-UIM. 10 An R-UIM simulator may be included as part of the system simulator (SS). Alternatively, to 11 perform the logical tests, R-U

23、IMs programmed with specific data may be used. The R-UIM 12 data is not defined within the initial conditions of the tests unless it differs from the default 13 values defined below. 14 5.1 Definition of Default Values for R-UIM/ME Interface Testing 15 An R-UIM containing the following default value

24、s is used for all tests of this section unless 16 otherwise stated. 17 For all data items, the logical default values and the coding within the elementary files 18 (EFs) of the R-UIM follow. 19 NOTE 1: Bx represents Byte x of the coding starting from left to right, i.e. MSB to LSB. 20 NOTE 2: Unless

25、 otherwise defined, the coding values are hexadecimal. 21 5.1.1 EFCST(CDMA Service Table) 22 Unless otherwise specified, the CDMA Service Table (EFCST) shall be coded as defined by the 23 entry “EFCST Setting 1” of Table 5-1. 24 Copyright Telecommunications Industry Association Provided by IHS under

26、 license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIA-1013 5-2Table 5-1. Coding of EFCST 1 Setting Description Byte Coding (binary) EFCST Setting 1 CHV1 disable function allocated and activated. Abbreviated dialing numbers allocated and activated. Fi

27、xed dialing numbers not activated. B1 xx0x1111 EFCST Setting 2 CHV1 disable function allocated and activated. Abbreviated dialing numbers allocated and activated. Fixed dialing numbers allocated and activated. B1 xx111111 EFCST Setting 3 CHV1 disable function not activated. Abbreviated dialing numbe

28、rs allocated and activated. Fixed dialing numbers not activated. B1 xx0x110x Note: The coding of bits designated x shall conform to the capabilities of the R-UIM simulator used. 5.1.2 EFADN(Abbreviated Dialing Number) 2 At least 10 records. 3 Record 1: 4 Length of alpha identifier: 32 characters 5 A

29、lpha identifier: “ABCDEFGHIJKLMNOPQRSTUVWXYZABCDEF“ 6 Length of BCD number: “03“ 7 TON and NPI: Telephony and Unknown 8 Dialed number: 123 9 CCI: None 10 Ext1: None 11 Coding: B1 B2 B3 . B32 B33 B34 B35 B36 B37 B38 B39 . B46 Record 1: 41 42 43 . 46 03 81 21 F3 FF FF FF . FF Copyright Telecommunicati

30、ons Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIA-1013 5-35.1.3 CHV1 (PIN) 1 Logically: 2468 2 Coding: B1 B2 B3 B4 B5 B6 B7 B8 3 32 34 36 38 FF FF FF FF 4 5.1.4 CHV2 (PIN2) 5 Logically: 3579 6 Coding:

31、 B1 B2 B3 B4 B5 B6 B7 B8 7 33 35 37 39 FF FF FF FF 8 5.1.5 Unblock CHV1 (PUK) 9 Logically: 13243546 10 Coding: B1 B2 B3 B4 B5 B6 B7 B8 11 31 33 32 34 33 35 34 36 12 5.1.6 Unblock CHV2 (PUK2) 13 Logically: 08978675 14 Coding: B1 B2 B3 B4 B5 B6 B7 B8 15 30 38 39 37 38 36 37 35 16 5.1.7 Definition of F

32、DN R-UIM 17 Some test cases require a different configuration from the one described in the previous 18 sections. For that purpose a default FDN R-UIM is defined. In general the values of the 19 FDN R-UIM are identical to the default R-UIM, with the following exceptions: 20 5.1.8 EFFDN(Fixed Dialing

33、 Numbers) 21 Multiple records: 22 Record 1: 23 Length of alpha identifier: 6 characters 24 Alpha identifier: “FDN111“ 25 Length of BCD number: “06“ 26 TON and NPI: Telephony and Unknown 27 Dialed number: 1357924680 28 CCI: None 29 Ext1: None 30 Copyright Telecommunications Industry Association Provi

34、ded by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIA-1013 5-4Coding for record 1: 1 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 46 44 4E 31 31 31 06 81 31 75 29 64 08 B14 B15 B16 B17 B18 B19 B20 FF FF FF FF FF FF FF Record 2: 2 Length

35、 of alpha identifier: 6 characters 3 Alpha identifier: “FDN222“ 4 Length of BCD number: “04“ 5 TON and NPI: Telephony and Unknown 6 Dialed number: 24680 7 CCI: None 8 Ext1: None 9 Coding for record 2: 10 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 46 44 4E 32 32 32 04 81 42 86 F0 FF FF B14 B15 B16 B1

36、7 B18 B19 B20 FF FF FF FF FF FF FF Record 3: 11 Length of alpha identifier: 6 characters 12 Alpha identifier: “FDN333“ 13 Length of BCD number: “0B“ 14 TON and NPI: Telephony and Unknown 15 Dialed number: 12345678901234567890 16 CCI: None 17 Ext1: None 18 Copyright Telecommunications Industry Associ

37、ation Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIA-1013 5-5Coding for record 3: 1 B1 B2 B3 B4 B5 B6 B7 B8 B9 B10 B11 B12 B13 46 44 4E 33 33 33 0B 81 21 43 65 87 09 B14 B15 B16 B17 B18 B19 B20 21 43 65 87 09 FF FF Copyrig

38、ht Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIA-1013 6-1No text.1 6 ME TEST PROCEDURES 2 For each test procedure the following five (5) subsections are included: 3 1) Definition an

39、d Applicability 4 2) Conformance Requirement 5 3) Test Purpose 6 4) Method of Test 7 (a) Initial Conditions 8 (b) Procedure 9 5) Test Requirement 10 6.1 MS Identification 11 6.1.1 Mobile Station Identifier 12 6.1.1.1 Definition and Applicability 13 This test verifies the use of the Mobile Station Id

40、entifier (Mobile Station ID MSID or Mobile 14 Station Identification Number MSIN), Mobile Country Code (MCC), and International 15 Mobile Station Identity (IMSI) stored within the R-UIM. 16 This test applies to MEs conforming to 1 using either ID-1 or Plug-in R-UIM. 17 6.1.1.2 Conformance Requiremen

41、t 18 The MS shall conform to the requirements specified in 2.12.3 of 11. 19 6.1.1.3 Test Purpose 20 The purpose of the test is to verify that the ME uses the IMSI_S, IMSI_11_12, and MCC of 21 the R-UIM. 22 6.1.1.4 Method of Test 23 6.1.1.4.1 Initial Conditions 24 The default R-UIM is installed into

42、the ME, and the MS is powered on. 25 6.1.1.4.2 Procedure 26 The tests shall be conducted in accordance with the procedures and requirements defined 27 in 2.12 (MSID, MCC, and IMSI) of 11. 28 6.1.1.5 Test Requirement 29 The ME shall conform to the requirements defined in 2.12.3 (Minimum Standard) of

43、11. 30 Copyright Telecommunications Industry Association Provided by IHS under license with EIANot for ResaleNo reproduction or networking permitted without license from IHS-,-,-TIA-1013 6-26.1.2 MS Recognizing the Home SID/NID 1 6.1.2.1 Definition and Applicability 2 This test verifies the ability

44、of the ME to read the appropriate home system information 3 from the R-UIM, compare that stored information to that received by the ME in the Sync 4 Channel Message, and to display the appropriate roaming indication to the user. 5 This test applies to MEs conforming to 1 using either ID-1 or Plug-in

45、 R-UIM. 6 6.1.2.2 Conformance Requirement 7 The ME shall compare the values of SIDp and NIDp stored within EFCDMAHOME with those 8 received in the Sync Channel Message (SIDr and NIDr, respectively) as the basis for 9 displaying a roaming indication to the user. 10 6.1.2.3 Test Purpose 11 The purpose

46、 of the test is to verify the ME is able to read, interpret, and apply during the 12 normal course of operation the values of SIDp and NIDp stored within EFCDMAHOME. 13 6.1.2.4 Method of Test 14 6.1.2.4.1 Initial Conditions 15 The values of the SID and NID fields of the Sync Channel Message transmit

47、ted by the 16 system simulator shall be set to equal those stored in the R-UIM (EFCDMAHOME). 17 6.1.2.4.2 Procedure 18 1) Power-on the mobile station. 19 2) Observe the status of any roaming indicator icon or display element on the 20 mobile station. 21 3) Set the values of the SID and NID fields of

48、 the Sync Channel Message 22 transmitted by the system simulator to values other than those stored in the R-23 UIM (EFCDMAHOME). 24 4) Power cycle (power-off then power-on) the mobile station. 25 5) Observe the status of any roaming indicator icon or display element on the 26 mobile station. 27 6.1.2.5 Test Requirement 28 1) In step 2) of the test procedure, the roaming indicator icon or display element of 29 the mobile station shall indicate the mobile station is operating within its home 30 system. 31