SMPTE ST 41-2004 Motion-Picture Film (16-mm) - Prints - Photographic Audio Records.pdf

《SMPTE ST 41-2004 Motion-Picture Film (16-mm) - Prints - Photographic Audio Records.pdf》由会员分享，可在线阅读，更多相关《SMPTE ST 41-2004 Motion-Picture Film (16-mm) - Prints - Photographic Audio Records.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 1 Scope 1.1 This standard specifies the lateral location, dimensions, and the reproducing speed of variable-area and variable-density photographic audio records on 16-mm motion-picture prints. 1.2 This standard also specifies the longitudinal picture-audio displacement. 1.3 The standard further spe

2、cifies the width scanned in the audio reproducer. 2 Audio record 2.1 The dimensions and location of the audio records shall be as specified in figure 1 and table 1. 2.2 The recording and reproducing slit images shall be positioned at an angle of 90 5 to the reference edge of the film. 3 Reproducing

3、speed The recording shall be made so that the audio record will reproduce properly at 24 perforations per second (approximately 36 ft 11 m per minute or 7.2 in 183 mm per second). This is equivalent to the projection speed of the picture film of 24 frames per second. 4 Longitudinal picture-audio dis

4、placement The audio record on the film shall precede the center of the corresponding picture (frame 0) by a distance of 26 frames frame in the direction of film travel during normal projection. NOTES 1 Motion-picture prints conforming to this standard are usually projected in accordance with SMPTE 2

5、33. 2 Motion-picture prints conforming to this standard are usually made on film made in accordance with SMPTE 109. 3 Motion-picture prints described in this standard are printed in accordance with ANSI/SMPTE 48. 4 Where the original audio record has been reduction printed in some stage of the proce

6、ss, it may be impossible to obtain the black septum on either side of the recorded area. The presence of a clear septum between the audio and picture areas which does not encroach on the minimum tolerances of the printed area shall not be a basis for rejection of prints. Shaded septum areas are inte

7、nded to include all unused areas on both sides of the audio record, up to the picture on one side and the film edge on the other. In no case shall the reduction printed area begin farther than 0.530 in (13.46 mm) nor extend less than 0.610 in (15.49 mm) from the reference edge of the film. Page 1 of

8、 3 pages SMPTE 41-2004 Revision of SMPTE 41-1999 Copyright 2004 by THE SOCIETY OF MOTION PICTURE AND TELEVISION ENGINEERS 595 W. Hartsdale Ave., White Plains, NY 10607 (914) 761-1100 Approved November 8, 2004 SMPTE STANDARD for Motion-Picture Film (16-mm) Prints Photographic Audio Records SMPTE 41-2

9、004 Page 2 of 3 pages Figure 1 Dimensions and location of the audio records Table 1 Specifications Dimensions Inches Millimeters A B C D E F G H J 0.611 min 0.513 ref 0.540 0.002 0.600 0.002 0.610 0.002 0.530 0.002 0.570 ref 0.071 ref 0.628 ref 5.52 min 13.03 ref 13.72 0.05 15.24 0.05 15.49 0.05 13.

10、46 0.05 14.48 ref 1.80 ref 15.95 ref SMPTE 41-2004 Page 3 of 3 pages Annex A (informative) Additional data A.1 As a working procedure, the accuracy of picture-audio displacement in a projection print is judged by screening in a review room. When the audio record is reproduced, the distance from the

11、center of the projector aperture to the audio-scanning point should be adjusted to bring picture and audio into synchronism for the average observer. This distance should be shortened by one frame for approximately each 50 ft (15 m) of distance from loudspeaker to audience. A.2 The dimensions in thi

12、s standard are measured from the perforated edge which is the edge used in factory control of 16-mm width films. Guiding from the perforated edge is the prevalent practice in the manufacture of 16-mm projectors. Films printed in 32-mm width and subsequently slit to 16-mm width will be guided and pos

13、itioned from factory-slit edges. Films printed on 35-mm width stock will either have one or no factory-made edge. The most common method would leave no factory-slit edge. Annex B (informative) Bibliography ANSI/SMPTE 48-1995 (R2004), Motion-Picture Film (16-mm) Picture and Sound Contact Printing Printed Areas SMPTE 109-2003, Motion-Picture Film (16-mm) Perforated 1R and 2R SMPTE 233-2001, Motion-Picture Film (16-mm) Projectable Image Area and Projector Usage