SMPTE ST 307M-2002 Television Digital Recording - 6 35-mm Type D-7 and Type D-12 Component Format - Tape Cassette.pdf
《SMPTE ST 307M-2002 Television Digital Recording - 6 35-mm Type D-7 and Type D-12 Component Format - Tape Cassette.pdf》由会员分享,可在线阅读,更多相关《SMPTE ST 307M-2002 Television Digital Recording - 6 35-mm Type D-7 and Type D-12 Component Format - Tape Cassette.pdf(40页珍藏版)》请在麦多课文档分享上搜索。
1、SMPTE STANDARD SMPTE 307M-2002 Revision of SMPTE 307M-1998 for Television Digital Recording - 6.35-mm Type D-7 and Type D-12 Component Format - TaDe Cassette Page 1 of 40 pages 1 Scope This standard specifies the dimensions for three types of 6.35-mm type D-7 and type 0-12 tape cassettes (M, L, and
2、EL) for use with digital recorders. NOTE -The cassette is used for more than a single recording format. The cassette provides no information to indicate the format of the recording contained on the tape within the cassette. 2 Measurements 2.1 Tests and measurements on cassette parameters shall be ca
3、rried out under the following atmospheric conditions: - Temperature: 20C f 1C - Relative humidity: (50 - Closed: Possible to record. 3.5 Tape type identification and cassette type detection 3.5.1 Identification board The dimensions and location of the identification board shall be as given in figure
4、s 12 to 14. The electrical characteristics shall be as given in tables 3 and 4 under the following conditions: - Each contact force of the connector shall be within 0.25 N to 0.4 N. - Each contact resistance of the connector shall be less than 0.5 ohms. The contact resistance shall be measured when
5、any value of DC current between 50 pA to 300 mA is applied. - Each conlaci impeaance ot the connector shall be less than 1.0 ohm. The contact impedance shall be measured when an AC current of 10 mA at 4 MHz is applied. Table 3 - Identif cation board for NI cassette Page 14 of 40 pages SMPTE 307M-200
6、2 Note 1 Contact element area Dimensions in millimeters NOTES 1 The contact element shall be located within the area indicated. 2 The activator shall not exceed the cassette surface. 3 The spacing between the contact element and the shell shall not exceed 0.3 mm. Figure 12 - Contact area of ID board
7、 for M cassette Page 15 o 40 pages SMPTE 307M-2002 Detail F Section B-B Note 1 Contact eienent area Dimensions in millimeters NOTES 1 The contact element shall be located within the area indicated. 2 The activator shall not exceed the cassette surface. 3 The spacing between the contact element and t
8、he shell shall not exceed 0.3 rnm. Figure 13 - Contact area of ID board for L cassette Page 16 of 40 pages SMPTE 3071111-2002 Note 1 :Contact element area Dimensions in millimeters NOTES 1 The contact element shall be located within the area indicated. 2 The activator shall not exceed the cassette s
9、urface. 3 The spacing between the contact element and the shell shall not exceed 0.3 mm. Figure 14 - Contact area of ID board for EL cassette Page 17 of 40 pages SMPTE 307M-2002 EL 3.5.2 Cassette-type detection hole 82 f 10 The dimensions and location of the cassette-type detection hole, detailed in
10、 figures 10 and 11, shall be as follows: - Open: EL cassette with 6.7 pm thick tape; - Closed: L cassette with 8.8 pm thick tape. 3.6 LeaderArailer tape 3.6.1 The light path shall be as specified in figures 15 to 17 3.6.2 The cassette shall include a leader and trailer tape. When attached to the hub
11、, the length between the splice point and the clamping point on the reel hub shall be as specified in table 5 and figures 15 to 17. Table 5 - Length of leader and trailer tape Length 75k 10 80k 10 Cassette size 3.6.3 The leaderitrailer tape material shall be polyester or its equivalent having a tran
12、smissivity of at least 65% when measured with an 800 nm to 1000 nm light source. 3.6.4 When attached to the hub, the leaderitrailer tape shall not separate when subjected to a force of 4 N or less. 3.6.5 The width of the leaderitrailer tape shall be 6.35 mm + O mm - 0.05 mm. 3.6.6 The thickness of t
13、he leaderitrailer tape shall be 15 pm + O pm - 3 pm. The splicing tape used to attach the leaderitrailer tape shall be applied to the nonmagnetic coated side. 3.7 Reels 3.7.1 The dimensions of the reels and the relationship between the reels and reel tables shall be as specified in figures 18 to 20.
14、 3.7.2 The reels shall be locked automatically when the cassette is removed from the re- corderiplayer. The number and shape of the teeth as well as the locking mechanism shall be as specified in figures 21 to 23. 3.7.3 When a cassette is inserted into the recorderiplayer, the reels shall be unlocke
15、d automatically as specified in figures 21 to 23. The force needed to release the reel lock shall be less than 1.2 N. Page 18 of 40 pages CMPTE 307M-2002 w Light path Leader and troiier tape Dimensions in millimeters NOTES 1 The light path, as shown, shall be unobstructed when the lid is open beyond
16、 85“. 2 The light path aperture shall be a 2.0-mm minimum diameter hole, but shall not exceed a 2.9-mm square area. Figure 15 - Light path and leader/trailer tape for M cassette Page 19 of 40 pages SMPTE 307M-2002 _ Figure 10a Light path r Magnetic side Fiqure i0b Lender and trniler tape Dimensions
17、in millimeters NOTES 1 The light path, as shown, shall be unobstructed when the lid is open beyond 85“. 2 The light path aperture shall be a 2.0-mm minimum diameter hole, but shall not exceed a 2.9-mm square area. Figure 16 - Light path and leaderhailer tape for L cassette Page 20 of 40 pages SMPTE
18、307M-2002 II I Figure 100 Light path Fiaure iOb Lender and traiier tape Dimensions in millimeters NOTES 1 The light path, as shown, shall be unobstructed when the lid is open beyond 85“. 2 The light path aperture shall be a 2.0-mm minimum diameter hole, but shall not exceed a 2.9-mm square area. Fig
19、ure 17 - Light path and leaderhrailer tape for EL cassette Page 21 of 40 pages SMPTE 307M-2002 c O 1 1 a , Ratchet for reei lock -Note 5 Note 6/ Detail C Appearance A Note 3 n 4 1 N n te 4 “- M rh Reei table sumort area Dimensions in millimeters NOTES 1 All dimensioned tolerances for the reel drive
20、holes shall be maintained through a depth of 7.4 mm. 2 The height of the reel table. 3 The reel spring pressure force shall be within a range of 0.65 N to 1.15 N when the height of the reel table support area is 0.7 mm f 0.25 mm from datum plane Z. 4 The flange of the reel shall not contact the shel
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SMPTEST307M2002TELEVISIONDIGITALRECORDING635MMTYPED7ANDTYPED12COMPONENTFORMATTAPECASSETTEPDF

链接地址:http://www.mydoc123.com/p-1046882.html