SMPTE ST 149-2004 Motion-Picture Film (8-mm Type S) - Perforated 1R.pdf

《SMPTE ST 149-2004 Motion-Picture Film (8-mm Type S) - Perforated 1R.pdf》由会员分享，可在线阅读，更多相关《SMPTE ST 149-2004 Motion-Picture Film (8-mm Type S) - Perforated 1R.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 1 Scope This standard specifies the cutting and perforating dimensions for 8-mm motion-picture film with 8-mm type S perforations along one edge and a perforation pitch of either 0.1664 in or 0.1667 in (4.227 mm or 4.234 mm). 2 Dimensions 2.1 The dimensions shall be as given in figure 1 and table 1

2、. 2.2 The dimensions pertain to a safety film as defined in SMPTE 223M. 2.3 The dimensions apply at the time of cutting and perforating for film adjusted to a temperature of 23C 1C (nominally converted to 73F 2F) and a relative humidity of (50 2)%. The manufacturer may indicate other nominal tempera

3、ture and humidity conditions under which the dimensions apply. Figure 1 8-mm type S film Page 1 of 2 pages SMPTE 149-2004 Revision of SMPTE 149-1999 Copyright 2004 by THE SOCIETY OF MOTION PICTURE AND TELEVISION ENGINEERS 595 W. Hartsdale Ave., White Plains, NY 10607 (914) 761-1100 Approved November

4、 8, 2004 SMPTE STANDARD for Motion-Picture Film (8-mm Type S) Perforated 1R SMPTE 149-2004 Page 2 of 2 pages Table 1 Specifications Dimensions Inches Millimeters A B B C D E L L R Film width Perforation pitch (long) Perforation pitch (short) Perforation width Perforation height Edge to perforation 1

5、00 consecutive perforation pitches 100 consecutive perforation pitches Radius of perforation fillet 0.3140 0.0015 0.1667 0.0004 0.1664 0.0004 0.0360 0.0004 0.0450 0.0004 0.020 0.002 16.670 0.017 16.640 0.017 0.005 0.001 7.976 0.038 4.234 0.010 4.227 0.010 0.914 0.010 1.143 0.010 0.51 0.05 423.42 0.4

6、3 422.66 0.43 0.13 0.03 NOTE The title of this standard was established by the application of a nomenclature system developed for all film dimension standards. Each title provides an indication of the film width, a code designation for the perforation shape (BH, KS, DH, or CS), or the number of rows

7、 of perforations (1R, 2R, etc.), depending upon which is the significant factor, or the perforation pitch without the decimal point. Annex A (informative) Additional data A.1 The user is reminded that, as a plastic, film can change dimensions temporarily due to moisture or temperature, or permanentl

8、y due to solvent loss or strain effect. A.2 Film for positive use has a longitudinal pitch 0.2% longer than its companion unprocessed negative. Shrinkage of the negative during aging and processing prior to printing will generally not exceed 0.2%. Thus, the processed negative stock is expected to be

9、 0.3% 0.1% shorter than the unprocessed positive. This difference will minimize slippage between the two on the 12-in (305-mm) circumference sprocket of the printer, assuming a film thickness of 0.0055 in to 0.0065 in (0.140 mm to 0.165 mm). A.3 The uniformity of pitch, hole size, and margin (dimens

10、ions B, C, D, and E) is an important variable affecting steadiness. Variations in these dimensions, from roll to roll, are of little significance compared to variations from one perforation to the next within any small group of consecutive perforations. As an example, the uniformity of the margin is

11、 uniquely critical for optical printing. During the printing process, the placement of the image on the film is usually with respect to successive lateral pairs of perforations at one-frame intervals. During subsequent projection, however, the portion of the image projected is usually located, not b

12、y these perforations, but by the edge of the film. The lateral steadiness of the projected image is therefore directly related to the frame-to-frame uniformity of the margin. A.4 For historical background on the development of this standard, refer to A. J. Miller and A. C. Robertson, “Motion-picture film Its size and dimensional characteristics,“ Journal of the SMPTE 74: 3-11; January 1965. Annex B (informative) Bibliography SMPTE 223M-2001, Motion-Picture Film Safety Film