SMPTE RP 207-2005 Transport of Program Description Data in Vertical Ancillary Data Packets《垂直辅助数据包中程序描述数据的传输》.pdf

《SMPTE RP 207-2005 Transport of Program Description Data in Vertical Ancillary Data Packets《垂直辅助数据包中程序描述数据的传输》.pdf》由会员分享，可在线阅读，更多相关《SMPTE RP 207-2005 Transport of Program Description Data in Vertical Ancillary Data Packets《垂直辅助数据包中程序描述数据的传输》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 Table of contents Forward 1 Scope 2 Normative references 3 Packet format 4 Descriptors Annex A (informative) Forward SMPTE (the Society of Motion Picture and Television Engineers) is an internationally recognized standards- developing organization. Headquartered and incorporated in the United State

2、s of America, SMPTE has members in over 80 countries on six continents. SMPTEs Engineering Documents, including Standards, Recommended Practices and Engineering Guidelines, are prepared by SMPTEs Technology Committees. Participation in these Committees is open to all with a bona fide interest in the

3、ir work. SMPTE cooperates closely with other standards-developing organizations, including ISO, IEC and ITU. SMPTE Engineering Documents are drafted in accordance with the rules given in Part XIII of its Administrative Practices. SMPTE Recommended Practice RP 207 was prepared by Technology Committee

4、 D27. 1 Scope SMPTE 334M defines a mapping of data in vertical ancillary data packets. In particular, it refers to a packet named program description which is identified by the following combination of data identifier (DID) and secondary data identifier (SDID): DID = 162hSDID = 101hThis packet carri

5、es data which define characteristics of the video and audio program material. It can be used by station equipment, for example, in producing PSIP (program and system information protocol) data in accordance with ATSC A/65. This practice recommends a format for the program description packet. Page 1

6、of 3 pages RP 207-2005 Revision of RP 207-2002 Copyright 2005 by THE SOCIETY OF MOTION PICTURE AND TELEVISION ENGINEERS 595 W. Hartsdale Ave., White Plains, NY 10607 (914) 761-1100 Approved March 22, 2005 SMPTE RECOMMENDED PRACTICE Transport of Program Description Data in Vertical Ancillary Data Pac

7、kets RP 207-2005 Page 2 of 3 pages 2 Normative references The following standards contain provisions which, through reference in this text, constitute provisions of this practice. At the time of publication, the editions indicated were valid. All standards are subject to revision, and parties to agr

8、eements based on this practice are encouraged to investigate the possibility of applying the most recent edition of the standards indicated below. ATSC A/53C, ATSC Digital Television Standard ATSC A/65B, Program and System Information Protocol for Terrestrial Broadcast and Cable ISO/IEC 13818-1:2000

9、, Information Technology Generic Coding of Moving Pictures and Associated Audio Information: Systems SMPTE 334M-2000, Television Vertical Ancillary Data Mapping for Bit-Serial Interface SMPTE RP 168-2002, Definition of Vertical Interval Switching Point for Synchronous Video Switching 3 Packet format

10、 Each data packet follows the format defined in SMPTE 291M for a type 2 vertical ancillary (ANC) data packet. It consists of the ancillary data flag (ADF), the data ID (DID), the secondary data ID (SDID), the data count (DC), the user data words (UDW), and the checksum (CS). The UDW consists of the

11、data payload plus forward error correction overhead. Each program description vertical ancillary packet contains exactly one descriptor, as defined in ATSC A/65, ATSC A/53, and ISO/IEC 13818-1. The format of the vertical ancillary packet is therefore as follows: Header: UDW: Sufix: ADF (3 words) Dat

12、a payload (variable) = 1 descriptor CS (1 word) DID = 162hSDID = 101hDC = variable 4 Descriptors Descriptors are uniquely identified by their descriptor tag. Any of the descriptors listed in table 6-25 of ATSC A/65, as well as ATSC A/53 and ISO/IEC 13818-1, may be transported as described in this pr

13、actice. Equipment that is intended to comply with this practice shall support those shown in the following table. The UDW consists of one descriptor. All descriptors in compliance with ISO/IEC 13818-1, section 2.6, consist of an 8-bit descriptor tag, followed by an 8-bit descriptor length, followed

14、by the data. The value of “length” is the number of bytes of data following the length byte. For example, the Redistribution Control (RC) descriptor format would be the descriptor tag byte of AAhfollowed by a length byte of 00hand no data bytes. In contrast, the Caption Service descriptor format wou

15、ld be the descriptor tag byte of 86h, followed by a length byte whose value will vary, followed by the variable length data bytes. RP 207-2005 Page 3 of 3 pages Table 1 Descriptors Descriptor name Descriptor tag AC-3 audio 81h Caption service 86h Content advisory 87h Redistribution control AAh Annex

16、 A (informative) The recommend space for placement of program description packets is in the luminance (Y) stream of the SMPTE 292 interface. NOTE Equipment designers should recognize that existing equipment installed in the field and conforming to the previous version of this document use only the l

17、uminance channel for data transmission. Therefore, receivers should be able to receive VANC packets carrying program description packets in any VANC ancillary data space. It is suggested that program description packets be repeated every two seconds. The available VANC area starts with the second li

18、ne after the switching line specified in SMPTE RP 168. Users should be aware that not all equipment transparently passes data in the vertical interval of the video signal. In some cases, data values in the vertical sync interval will not be preserved during signal processing and manipulation. Devices that do not preserve the entire vertical interval may require additional support equipment to handle the vertical interval.