SMPTE RP 129-1995 Requirements for 35- 16- and 8-mm Type S Tape Splices on Magnetic Audio Recording Motion-Picture Film《磁录音电影胶片上35 mm 16 mm和8 mm S型磁带拼接要求》.pdf

《SMPTE RP 129-1995 Requirements for 35- 16- and 8-mm Type S Tape Splices on Magnetic Audio Recording Motion-Picture Film《磁录音电影胶片上35 mm 16 mm和8 mm S型磁带拼接要求》.pdf》由会员分享，可在线阅读，更多相关《SMPTE RP 129-1995 Requirements for 35- 16- and 8-mm Type S Tape Splices on Magnetic Audio Recording Motion-Picture Film《磁录音电影胶片上35 mm 16 mm和8 mm S型磁带拼接要求》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、SMPTE RP*129 95 357YOL 0002006 875 SMPTE RECOMMENDED PRACTICE Requirements for 35-, 16- and 8-mm RP 129-1995 Revision of RP 129-1985 Type S Tape Splices on Magnetic Audio Recording Motion-Picture Film 1 Scope This practice specifies the significant requirements for tape splices for 35-, 16-, and 8-m

2、m type S magnetic motion-picture film intended for audio recording. 2 Requirements 2.1 The requirements shall apply to magnetic audio recording films within acceptable shrink- age tolerances. 2.2 The film width at the splice shall not be increased by more than 0.003 in (0.08 mm) over the film width

3、being spliced. 2.3 The spliced film shall be aligned so that if one portion of the spliced film is placed against a straightedge, the other portion will not deviate more than 0.006 in (0.15 mm) in 5 in (125 mm). The perforations across the splice and the film edges shall be aligned in accordance wit

4、h figure 1. The spliced film shall maintain nominal perforation pitch as specified for the film gauge used. The splice shall have a negligible gap between the mated cuts of the film ends and there shall not be any film overlap at the splice. 2.4 An angle of 73“ to the edge of the film is preferred t

5、o minimize hinging and reduce Page 1 of 2 pages audibility as the splice passes over the head gap. However, an angle of 90“ is acceptable. 2.5 The dimensions of the splicing tape applied to secure a splice shall not interfere with the film width dimensions specified for the particular film. Splicing

6、 tape shall not interfere with sprocket hole perforation opening dimensions (see figures 2, 3, and 4). 2.6 It is recommended that the splicing tape adhere to not less than 0.3 in (7.6 mm) on each side of the cut to ensure adequacy of retention for the normal use of each film gauge. 2.7 Tape splices

7、shall be made with a tape having a thickness less than 0.003 in (0.08 mm) and resulting in a splice capable of withstanding 10 oz (283 gr) of longitudinal tension without dimensional change. 2.8 The splicing tape shall adhere uniformly to the film without corrugations or entrapped air bubbles. 2.9 T

8、he splicing tape used shall encompass the full width of the film and be applied to the base side only. 2.1 O Splice cuts and splicing tape edges shall be cen- tered between perforations (see figures 2,3, and 4). 0.002 IN MAX t I I 0.002 IN MAX Figure 1 - Splice alignment viewed base up Copyright Q 1

9、995 by the SOCIETY OF MOTION PICTURE AND TELEVISION ENGINEERS 595 W. Hartsdale Ave., White Plains, NY 10607 (914) 761-1100 Approved August 1,1995 SMPTE RP*129 95 8357401 0002007 701 RP 1281995 Figure 2 - Sound splice on 35-mm stock viewed base up Figure 3 - Sound splice on 16-mm stock viewed base up Figure 4 - Sound splice on &mm type S stock viewed base up Page 2 of 2 pages