SANS 60137-2010 Insulated bushings for alternating voltages above 1 000 V《交流电压1000V以上的绝缘套管》.pdf

《SANS 60137-2010 Insulated bushings for alternating voltages above 1 000 V《交流电压1000V以上的绝缘套管》.pdf》由会员分享，可在线阅读，更多相关《SANS 60137-2010 Insulated bushings for alternating voltages above 1 000 V《交流电压1000V以上的绝缘套管》.pdf（62页珍藏版）》请在麦多课文档分享上搜索。

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-20634-5 SANS 60137:2010Edition 3IEC 60137:2008Edition 6SOUTH AFRICAN NATIONAL STANDARD Insulated bushings for alternating voltages above 1

4、 000 V This national standard is the identical implementation of IEC 60137:2008 and is adopted with the permission of the International Electrotechnical Commission. Published by SABS Standards Division 1 Dr Lategan Road Groenkloof Private Bag X191 Pretoria 0001Tel: +27 12 428 7911 Fax: +27 12 344 15

5、68 www.sabs.co.za SABS SANS 60137:2010 Edition 3 IEC 60137:2008 Edition 6 Table of changes Change No. Date Scope National foreword This South African standard was approved by National Committee SABS SC 67D, Electricity distribution systems and components Insulators, in accordance with procedures of

6、the SABS Standards Division, in compliance with annex 3 of the WTO/TBT agreement. This SANS document was published in January 2010. This SANS document supersedes SANS 60137:2004 (edition 2). IEC 60137Edition 6.0 2008-07INTERNATIONAL STANDARD NORME INTERNATIONALEInsulated bushings for alternating vol

7、tages above 1 000 V Traverses isoles pour tensions alternatives suprieures 1 000 V INTERNATIONAL ELECTROTECHNICAL COMMISSION COMMISSION ELECTROTECHNIQUE INTERNATIONALE XAICS 29.080.20 PRICE CODECODE PRIXISBN 2-8318-9916-8 Registered trademark of the International Electrotechnical Commission Marque d

8、pose de la Commission Electrotechnique Internationale SANS 60137:2010This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS . 2 60137 IEC:2008 CONTENTS FOREWORD.6 INTRODUCTION.8 1 Scope.9 2 Normative references .9 3 Terms and definitions .10 4 Rating

9、s.16 4.1 Standard values of highest voltage for equipment (Um).16 4.2 Standard values of rated current (Ir)16 4.3 Standard values of rated thermal short-time current (Ith).16 4.4 Standard values of rated dynamic current (Id) .17 4.5 Minimum withstand values of cantilever load .17 4.6 Angle of mounti

10、ng .18 4.7 Minimum nominal creepage distance.18 4.8 Temperature limits and temperature rise .18 4.9 Standard insulation levels .20 4.10 Test tap on transformer bushings 22 5 Operating conditions 22 5.1 Temporary overvoltages 22 5.2 Altitude22 5.3 Temperature of ambient air and immersion media .23 5.

11、4 Seismic conditions 24 6 Ordering information and markings.24 6.1 Enumeration of characteristics 24 6.1.1 Application 24 6.1.2 Classification of bushings 24 6.1.3 Ratings24 6.1.4 Operating conditions24 6.1.5 Design.25 6.2 Markings .26 7 Test requirements 27 7.1 General requirements27 7.2 Test class

12、ification27 7.2.1 Type tests .28 7.2.2 Routine tests .29 7.2.3 Special tests29 7.3 Condition of bushings during dielectric and thermal tests 29 8 Type tests 31 8.1 Dry or wet power-frequency voltage withstand test 31 8.1.1 Applicability.31 8.1.2 Test method and requirements 31 8.1.3 Acceptance .31 8

13、.2 Long duration power-frequency voltage withstand test (ACLD) 32 8.2.1 Applicability.32 8.2.2 Test method and requirements 32 8.2.3 Acceptance .32 8.3 Dry lightning impulse voltage withstand test (BIL)33 SANS 60137:2010This s tandard may only be used and printed by approved subscription and freemai

14、ling clients of the SABS .60137 IEC:2008 3 8.3.1 Applicability.33 8.3.2 Test method and requirements 33 8.3.3 Acceptance .33 8.4 Dry or wet switching impulse voltage withstand test (SIL)34 8.4.1 Applicability.34 8.4.2 Test method and requirements 34 8.4.3 Acceptance .34 8.5 Thermal stability test .3

15、5 8.5.1 Applicability.35 8.5.2 Test method and requirements 35 8.5.3 Acceptance .36 8.6 Electromagnetic compatibility tests (EMC).36 8.6.1 Emission test.36 8.6.2 Immunity test.37 8.7 Temperature rise test 37 8.7.1 Applicability.37 8.7.2 Test method and requirements 37 8.7.3 Acceptance .39 8.8 Verifi

16、cation of thermal short-time current withstand .39 8.8.1 Applicability.39 8.8.2 Verification method and requirements39 8.8.3 Acceptance .40 8.9 Cantilever load withstand test41 8.9.1 Applicability.41 8.9.2 Test method and requirements 41 8.9.3 Acceptance .41 8.10 Tightness test on liquid-filled, com

17、pound-filled and liquid-insulated bushings 41 8.10.1 Applicability.41 8.10.2 Test method and requirements 42 8.10.3 Acceptance .42 8.11 Internal pressure test on gas-filled, gas-insulated and gas-impregnated bushings .42 8.11.1 Applicability.42 8.11.2 Test method and requirements 42 8.11.3 Acceptanc

18、e .42 8.12 External pressure test on partly or completely gas-immersed bushings .42 8.12.1 Applicability.42 8.12.2 Test method and requirements 42 8.12.3 Acceptance .43 8.13 Verification of dimensions .43 8.13.1 Applicability.43 8.13.2 Acceptance .43 9 Routine tests 43 9.1 Measurement of dielectric

19、dissipation factor (tan ) and capacitance at ambient temperature .43 9.1.1 Applicability.43 9.1.2 Test method and requirements 43 9.1.3 Acceptance .43 9.2 Dry lightning impulse voltage withstand test (BIL)44 SANS 60137:2010This s tandard may only be used and printed by approved subscription and free

20、mailing clients of the SABS . 4 60137 IEC:2008 9.2.1 Applicability.44 9.2.2 Test method and requirements 44 9.2.3 Acceptance .44 9.3 Dry power-frequency voltage withstand test 44 9.3.1 Applicability.44 9.3.2 Test method and requirements 45 9.3.3 Acceptance .45 9.4 Measurement of partial discharge qu

21、antity 45 9.4.1 Applicability.45 9.4.2 Test method and requirements 45 9.4.3 Acceptance .45 9.5 Tests of tap insulation .46 9.5.1 Applicability and test requirements 46 9.5.2 Acceptance .46 9.6 Internal pressure test on gas-filled, gas-insulated and gas-impregnated bushings .46 9.6.1 Applicability.4

22、6 9.6.2 Test method and requirements 47 9.6.3 Acceptance .47 9.7 Tightness test on liquid-filled, compound-filled and liquid-insulated bushings 47 9.7.1 Applicability.47 9.7.2 Test method and requirements 47 9.7.3 Acceptance .47 9.8 Tightness test on gas-filled, gas-insulated and gas-impregnated bus

23、hings 47 9.8.1 Applicability.47 9.8.2 Test method and requirements 47 9.8.3 Acceptance .48 9.9 Tightness test at the flange or other fixing device48 9.9.1 Applicability.48 9.9.2 Test method and requirements 48 9.9.3 Acceptance .48 9.10 Visual inspection and dimensional check.49 9.10.1 Applicability.

24、49 9.10.2 Acceptance .49 10 Requirements and tests for bushings of highest voltages for equipment equal to or less than 52 kV made of ceramic, glass or inorganic materials, resin or combined insulation49 10.1 Temperature requirements 49 10.2 Level of immersion medium .49 10.3 Markings .49 10.4 Test

25、requirements .50 10.4.1 Type tests .50 10.4.2 Routine tests .50 11 Recommendations for transport, storage, erection, operation and maintenance51 11.1 Conditions during transport, storage and installation .51 11.2 Installation 51 11.3 Unpacking and lifting.51 11.4 Assembly 52 11.4.1 Mounting .52 SANS

26、 60137:2010This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .60137 IEC:2008 5 11.4.2 Connections 52 11.4.3 Final installation inspection52 11.5 Operation 53 11.6 Maintenance53 11.6.1 General .53 11.6.2 Recommendation for the manufacturer 53 11.

27、6.3 Recommendations for the user 53 11.6.4 Failure report.54 12 Safety.55 12.1 Electrical aspects 55 12.2 Mechanical aspects.55 12.3 Thermal aspects55 13 Environmental aspects .55 Bibliography57 Figure 1 Altitude correction factor 23 Figure 2 Marking plate for bushings for highest voltage for equipm

28、ent greater than 100 kV (see 6.2) 26 Figure 3 Marking plate for bushings for highest voltage for equipment equal to or less than 100 kV, except for bushings for which Figure 2 is applicable (see 6.2).27 Figure 4 Marking plate for bushings for highest voltage for equipment equal to or less than 52 kV

29、 made of ceramic, glass or inorganic materials, resin or combined insulation (see 10.3) .27 Figure 5 Voltage profile for long duration test ACLD 32 Table 1 Minimum values of cantilever withstand load (see 4.5 and 8.9)17 Table 2 Maximum values of temperature and temperature rise above ambient air (se

30、e 4.8) .19 Table 3 Temperature of ambient air and immersion media (see 5.3) 20 Table 4 Insulation levels for highest voltage for equipment (see 4.9, 8.1, 8.3, 8.4, 9.2 and 9.3) 21 Table 5 Applicability of type tests (see 7.2.1, excluding bushings according to Clause 10) 28 Table 6 Applicability of r

31、outine tests (see 7.2.2, excluding bushings according to Clause 10) 29 Table 7 Correction of test voltages (see 7.3)31 Table 8 Maximum values of tan and tan increase (see 9.1) .44 Table 9 Maximum values of partial discharge quantity (see 8.2 and 9.4) 46 Table 10 Applicability of type tests for bushi

32、ngs according to Clause 10 (see 10.4.1) 50 Table 11 Applicability of routine tests for bushings according to Clause 10 (see 10.4.2)51 SANS 60137:2010This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS . 6 60137 IEC:2008 INTERNATIONAL ELECTROTECHNI

33、CAL COMMISSION _ INSULATED BUSHINGS FOR ALTERNATING VOLTAGES ABOVE 1 000 V FOREWORD 1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising all national electrotechnical committees (IEC National Committees). The object of IEC is to promote in

34、ternational co-operation on all questions concerning standardization in the electrical and electronic fields. To this end and in addition to other activities, IEC publishes International Standards, Technical Specifications, Technical Reports, Publicly Available Specifications (PAS) and Guides (herea

35、fter referred to as “IEC Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested in the subject dealt with may participate in this preparatory work. International, governmental and non-governmental organizations liaising with the IEC also parti

36、cipate in this preparation. IEC collaborates closely with the International Organization for Standardization (ISO) in accordance with conditions determined by agreement between the two organizations. 2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an

37、 international consensus of opinion on the relevant subjects since each technical committee has representation from all interested IEC National Committees. 3) IEC Publications have the form of recommendations for international use and are accepted by IEC National Committees in that sense. While all

38、reasonable efforts are made to ensure that the technical content of IEC Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any misinterpretation by any end user. 4) In order to promote international uniformity, IEC National Committees undertake to appl

39、y IEC Publications transparently to the maximum extent possible in their national and regional publications. Any divergence between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in the latter. 5) IEC provides no marking procedure to indicate it

40、s approval and cannot be rendered responsible for any equipment declared to be in conformity with an IEC Publication. 6) All users should ensure that they have the latest edition of this publication. 7) No liability shall attach to IEC or its directors, employees, servants or agents including indivi

41、dual experts and members of its technical committees and IEC National Committees for any personal injury, property damage or other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and expenses arising out of the publication, use of, or reliance upon, t

42、his IEC Publication or any other IEC Publications. 8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is indispensable for the correct application of this publication. 9) Attention is drawn to the possibility that some of the elements of t

43、his IEC Publication may be the subject of patent rights. IEC shall not be held responsible for identifying any or all such patent rights. International Standard IEC 60137 has been prepared by sub-committee 36A: Insulated bushings, of IEC technical committee 36: Insulators. This sixth edition cancels

44、 and replaces the fifth edition, published in 2003, and constitutes a technical revision. This edition includes the following significant technical changes with respect to the previous edition: Long duration power-frequency for transformer bushings. Special requirements for type and acceptance tests

45、 applicable to transformer and GIS bushings. Specific insulation levels for bushings fitted to transformers and GIS. According to IEC Guide 111, clauses relating to safety and the environment have been added. The altitude correction procedure has been revised ( 1 000 m). SANS 60137:2010This s tandar

46、d may only be used and printed by approved subscription and freemailing clients of the SABS .60137 IEC:2008 7 The text of this standard is based on the following documents: FDIS Report on voting 36A/134/FDIS 36A/135/RVDFull information on the voting for the approval of this standard can be found in

47、the report on voting indicated in the above table. This publication has been drafted in accordance with the ISO/IEC Directives, Part 2. The committee has decided that the contents of this publication will remain unchanged until the maintenance result date indicated on the IEC web site under “http:/w

48、ebstore.iec.ch“ in the data related to the specific publication. At this date, the publication will be reconfirmed, withdrawn, replaced by a revised edition, or amended. SANS 60137:2010This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS . 8 60137

49、IEC:2008 INTRODUCTION In the preparation of this standard further consideration has been given to the test requirements for power transformers as described in IEC 60076-3:2000. Extensions have been made to the requirements for lightning impulse type testing and an additional test - long duration power-frequency withstand test - has been included. In anticipation of changes in the creepage correction factors defined in IEC 60815 and currently under review by TC 36, details of the