SANS 28017-2009 Rubber hoses and hose assemblies Wire or textile reinforced for dredging applications - Specification《疏浚用钢丝或织物增强的橡胶软管及软管组合件 规范》.pdf

《SANS 28017-2009 Rubber hoses and hose assemblies Wire or textile reinforced for dredging applications - Specification《疏浚用钢丝或织物增强的橡胶软管及软管组合件 规范》.pdf》由会员分享，可在线阅读，更多相关《SANS 28017-2009 Rubber hoses and hose assemblies Wire or textile reinforced for dredging applications - Specification《疏浚用钢丝或织物增强的橡胶软管及软管组合件 规范》.pdf（22页珍藏版）》请在麦多课文档分享上搜索。

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-23830-8 SANS 28017:2009Edition 1ISO 28017:2009Edition 1SOUTH AFRICAN NATIONAL STANDARD Rubber hoses and hose assemblies, wire or textile r

4、einforced, for dredging applications Specification This national standard is the identical implementation of ISO 28017:2009 and is adopted with the permission of the International Organization for Standardization. Published by SABS Standards Division 1 Dr Lategan Road Groenkloof Private Bag X191 Pre

5、toria 0001Tel: +27 12 428 7911 Fax: +27 12 344 1568 www.sabs.co.za SABS SANS 28017:2009 Edition 1 ISO 28017:2009 Edition 1 Table of changes Change No. Date Scope National foreword This South African standard was approved by National Committee SABS TC 45, Rubber and rubber products, in accordance wit

6、h the SABS Standards Division, in compliance with annex 3 of the WTO/TBT agreement. This SANS document was published in December 2009. Reference numberISO 28017:2009(E)ISO 2009INTERNATIONAL STANDARD ISO28017First edition2009-07-15Rubber hoses and hose assemblies, wire or textile reinforced, for dred

7、ging applications Specification Tuyaux et flexibles en caoutchouc, armature textile ou mtallique, pour des applications de dragage Spcifications SANS 28017:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 28017:2009(E) PDF disclaimer T

8、his PDF file may contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this file, parties accept t

9、herein the responsibility of not infringing Adobes licensing policy. The ISO Central Secretariat accepts no liability in this area. Adobe is a trademark of Adobe Systems Incorporated. Details of the software products used to create this PDF file can be found in the General Info relative to the file;

10、 the PDF-creation parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. COPYRIGHT PROTECTED DO

11、CUMENT ISO 2009 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISOs member bo

12、dy in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2009 All rights reservedSANS 28017:2009This s tandard may only be used and printed by approv

13、ed subscription and freemailing clients of the SABS .ISO 28017:2009(E) ISO 2009 All rights reserved iiiContents Page Foreword iv 1 Scope . 1 2 Normative references . 1 3 Terms and definitions. 2 4 Classification. 2 5 Materials and construction 3 6 Dimension and tolerances . 4 7 Physical properties.

14、5 8 Test certificate. 8 9 Marking 9 10 Recommendations for packaging and storage . 9 Annex A (normative) Type tests and routine tests . 10 Annex B (normative) Measurement of adhesion between end fitting and lining 11 SANS 28017:2009This s tandard may only be used and printed by approved subscription

15、 and freemailing clients of the SABS .ISO 28017:2009(E) iv ISO 2009 All rights reservedForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out t

16、hrough ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO colla

17、borates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Sta

18、ndards. Draft International Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements o

19、f this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 28017 was prepared by Technical Committee ISO/TC 45, Rubber and rubber products, Subcommittee SC 1, Hoses (rubber and plastics). SANS 28017:2009This s tandard may

20、 only be used and printed by approved subscription and freemailing clients of the SABS .INTERNATIONAL STANDARD ISO 28017:2009(E) ISO 2009 All rights reserved 1Rubber hoses and hose assemblies, wire or textile reinforced, for dredging applications Specification 1 Scope This International Standard spe

21、cifies requirements for two types, seven classes and three grades of wire- or textile-reinforced dredging hoses with nominal sizes ranging from 100 to 1 200. Within each class, all grades and sizes have the same maximum working pressure. Such hoses are suitable for the delivery or suction of seawate

22、r, freshwater, silt, sand, coral and small stones with a specific gravity in the range from 1,0 to 2,3 at ambient temperatures ranging from 10 C to +40 C. This International Standard covers two types of hose, as follows: type 1: floating type, for delivery only, which includes flotation material to

23、give the hose buoyancy; type 2: submarine type for delivery and suction. This International Standard does not specify requirements concerning the service life of hoses or hose assemblies. Specifying such requirements is the responsibility of the customer, in consultation with the hose manufacturer.

24、2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. ISO 1402, Rubber and plast

25、ics hoses and hose assemblies Hydrostatic testing ISO 1431-1, Rubber, vulcanized or thermoplastic Resistance to ozone cracking Part 1: Static and dynamic strain testing ISO 1746, Rubber or plastics hoses and tubing Bending tests 1)ISO 4649:2002, Rubber, vulcanized or thermoplastic Determination of a

26、brasion resistance using a rotating cylindrical drum device ISO 4671, Rubber and plastics hoses and hose assemblies Methods of measurement of the dimensions of hoses and the lengths of hose assemblies ISO 7233:2006, Rubber and plastics hoses and hose assemblies Determination of resistance to vacuum

27、ISO 8033, Rubber and plastics hoses Determination of adhesion between components ISO 8330, Rubber and plastics hoses and hose assemblies Vocabulary ISO 8331, Rubber and plastics hoses and hose assemblies Guidelines for selection, storage, use and maintenance 1) Under revision as ISO 10619-1. SANS 28

28、017:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 28017:2009(E) 2 ISO 2009 All rights reserved3 Terms and definitions For the purposes of this document, the terms and definitions given in ISO 8330 apply. 4 Classification 4.1 Classes

29、 Seven classes of hose are specified, distinguished by their maximum working pressure, of nominal sizes from 100 to 1 200, as shown in Table 1. Table 1 Classes and corresponding maximum working pressures and nominal sizes Class 5 10 15 20 25 30 40 Maximum working pressure, MWP MPa (bar) Nominal size

30、 0,5 (5) 1,0 (10) 1,5 (15) 2,0 (20) 2,5 (25) 3,0 (30) 4,0 (40) 100 X X X X X X X 150 X X X X X X X 200 X X X X X X X 250 X X X X X X N/A 300 X X X X X X N/A 350 X X X X X X N/A 400 X X X X X X N/A 450 X X X X X X N/A 500 X X X X X X N/A 550 X X X X X X N/A 600 X X X X X X N/A 650 X X X X X X N/A 700

31、 X X X X X X N/A 750 X X X X X X N/A 800 X X X X X X N/A 850 X X X X X X N/A 900 X X X X X X N/A 1 000 X X X X X X N/A 1 100 X X X X X X N/A 1 200 X X X X X N/A N/A NOTE X = Applicable, N/A = Not applicable. SANS 28017:2009This s tandard may only be used and printed by approved subscription and free

32、mailing clients of the SABS .ISO 28017:2009(E) ISO 2009 All rights reserved 34.2 Grades Type 2 hoses are classified into three grades, A, B and C, according to their construction, as shown in Table 2. Type 1 hoses are not divided into grades. Table 2 Grades Construction and purpose Type Grade Number

33、 of reinforcing wires Purpose 1 0 Delivery only A 2 Delivery or suction B 1 Delivery or suction 2 C 0 Delivery onlyThe types and grades available in each class (i.e. for each maximum working pressure) are as shown in Table 3. Table 3 Types and grades available in each class Class 5 10 15 20 25 30 40

34、 Maximum working pressure, MWP MPa (bar) Type Grade 0,5 (5) 1,0 (10) 1,5 (15) 2,0 (20) 2,5 (25) 3,0 (30) 4,0 (40) 1 X X X X X X X A X X X N/A N/A N/A N/A B X X X N/A N/A N/A N/A 2 C X X X X X X X NOTE X = Applicable, N/A = Not applicable. 5 Materials and construction 5.1 Hoses Type 1 hose assemblies

35、 shall consist of an abrasion-resistant rubber lining, one or more layers of steel or textile reinforcement, a textile-reinforced rubber undercover, a flexible closed-cell flotation material integrally fitted round the hose body as described in 5.2, an abrasion- and weather-resistant rubber or therm

36、oplastic outer cover, which may be textile-reinforced, and end fittings as described in 5.3 on both ends. Type 2 hose assemblies shall consist of an abrasion-resistant rubber lining, one or more layers of steel or textile reinforcement, a textile-reinforced rubber, full rubber or thermoplastic cover

37、 at least 6 mm thick for hoses of nominal size less than 500, at least 10 mm thick for hoses of nominal size in the range from 500 to 850 inclusive and at least 12 mm thick for hoses of nominal size in the range from 900 to 1 200 inclusive, and end fittings as described in 5.3 on both ends. SANS 280

38、17:2009This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 28017:2009(E) 4 ISO 2009 All rights reserved5.2 Flotation material The flotation material shall adhere firmly both to the hose body and to the outer cover so that it cannot move or te

39、nd to become detached in service. At the ends of the hose, a space shall be provided to facilitate the insertion of connection bolts and to allow the use of mechanical tools for tightening nuts on the bolts. 5.3 End fittings and end connections End fittings shall be mechanically and chemically bonde

40、d to the hose body. With hoses intended for delivery use only, clamped-on and swaged-on nipples are not acceptable, but such nipples may be utilized with hoses intended for suction use. Alternatively, flanged end connections built up of hose reinforcement, lining and cover material are acceptable pr

41、ovided they are additionally reinforced by steel stiffening rings to avoid distortion when the connection bolts are tightened. All hose assemblies shall be fitted with either end fittings or flanged end connections unless otherwise required by the end user. 6 Dimension and tolerances 6.1 Diameters W

42、hen measured in accordance with ISO 4671, the inside diameters of hoses shall conform to the values given in Table 4. When measured in accordance with ISO 4671, the outside diameters of hoses shall conform to the values specified by the customer. Table 4 Diameters of hoses Actual inside diameter mm

43、Nominal size min. max. 100 90 110 150 140 160 200 190 210 250 240 260 300 290 310 350 340 360 400 390 410 450 440 460 500 490 510 550 540 560 600 590 610 650 640 660 700 690 710 750 740 760 800 790 810 850 840 860 900 890 910 1 000 990 1 010 1 100 1 090 1 110 1 200 1 190 1 210 SANS 28017:2009This s

44、tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 28017:2009(E) ISO 2009 All rights reserved 56.2 Hose unit length The hose unit length shall be determined according to the conditions of use. Unless otherwise agreed between the customer and the ma

45、nufacturer, the tolerances on the unit length shall be +2 % and 2 %. 7 Physical properties 7.1 Rubber compounds 7.1.1 Abrasion resistance of lining 7.1.1.1 Test pieces Test pieces shall be prepared from sheets of lining compound (of cure state equivalent to that of the hose) of thickness at least 6

46、mm. The method of preparation shall be as specifed in ISO 4649. 7.1.1.2 Abrasion resistance When the test is carried out in accordance with ISO 4649:2002, method A, the relative volume loss Vrelshall not be greater than 200 mm3. 7.1.2 Ozone resistance of cover 7.1.2.1 Test pieces Test pieces shall b

47、e prepared from sheets of cover compound (of cure state equivalent to that of the hose) of thickness at least 2 mm. The method of preparation shall be as specified in ISO 1431-1. For type 1 hoses, it is the compound from which the outer cover (that surrounding the flotation material) is made which i

48、s tested. 7.1.2.2 Ozone resistance When the test is carried out in accordance with ISO 1431-1, no cracking or other deterioration of the test pieces shall be visible under 2 magnification after 72 h at 40 C and 20 % strain in 50 pphm ozone. 7.2 Performance requirements 7.2.1 Hydrostatic requirements

49、 When determined in accordance with ISO 1402, the proof pressure and the minimum burst pressure of hoses and hose assemblies shall conform to the values given in Table 5. Burst testing shall be carried out on a mid-range nominal size of each design in the manufacturers range. The minimum burst pressure of other sizes of the same design, construction (with a reinforcement type identical to that of the hose tested but not necessarily the same number of plies), materials and method of manufacture