SANS 1700-9-1-2008 Fasteners Part 9 Hexagon socket head screws Section 1 Hexagon socket head cap screws《紧固件 第9部分 内六角凹头螺钉 第1子部分 内六角圆柱头螺钉》.pdf

《SANS 1700-9-1-2008 Fasteners Part 9 Hexagon socket head screws Section 1 Hexagon socket head cap screws《紧固件 第9部分 内六角凹头螺钉 第1子部分 内六角圆柱头螺钉》.pdf》由会员分享，可在线阅读，更多相关《SANS 1700-9-1-2008 Fasteners Part 9 Hexagon socket head screws Section 1 Hexagon socket head cap screws《紧固件 第9部分 内六角凹头螺钉 第1子部分 内六角圆柱头螺钉》.pdf（18页珍藏版）》请在麦多课文档分享上搜索。

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-20972-8 SANS 1700-9-1:2008Edition 2ISO 4762:2004Edition 4SOUTH AFRICAN NATIONAL STANDARD Fasteners Part 9: Hexagon socket head screws Sect

4、ion 1: Hexagon socket head cap screws This national standard is the identical implementation of ISO 4762:2004 and is adopted with the permission of the International Organization for Standardization. Published by Standards South Africa 1 dr lategan road groenkloof private bag x191 pretoria 0001 tel:

5、 012 428 7911 fax: 012 344 1568 international code + 27 12 www.stansa.co.za Standards South Africa SANS 1700-9-1:2008 Edition 2 ISO 4762:2004 Edition 4 Table of changes Change No. Date Scope National foreword This South African standard was approved by National Committee StanSA TC 5120.01, Screw thr

6、eads and fasteners, in accordance with procedures of Standards South Africa, in compliance with annex 3 of the WTO/TBT agreement. This SANS document was published in April 2008. This SANS document supersedes SANS 1700-9-1:1998 (edition 1). INTERNATIONALSTANDARDISO4762Fourth edition2004-03-01Referenc

7、e numberISO 4762:2004(E) ISO 2004Hexagon socket head cap screwsVis tte cylindrique six pans creuxSANS 1700-9-1:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 4762:2004(E)ii ISO 2004 All rights reservedPDF disclaimerThis PDF file may

8、contain embedded typefaces. In accordance with Adobes licensing policy, this file may be printed or viewed but shallnot be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. Indownloading this file, parties accept therein the responsi

9、bility of not infringing Adobes licensing policy. The ISO Central Secretariataccepts no liability in this area.Adobe is a trademark of Adobe Systems Incorporated.Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creationparam

10、eters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In theunlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below. ISO 2004All rights reserved. Unless otherwise

11、specified, no part of this publication may be reproduced or utilized in any form or by any means,electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below orISOs member body in the country of the requester.ISO copyright officeC

12、ase postale 56 CH-1211 Geneva 20Tel. + 41 22 749 01 11Fax + 41 22 749 09 47E-mail copyrightiso.orgWeb www.iso.orgPublished in SwitzerlandSANS 1700-9-1:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 4762:2004(E) ISO 2004 All rights re

13、served iiiContents Page1 Scope 12 Normative references 13 Dimensions 24 Requirements and reference International Standards . 95 Designation 9Annex A (informative) Masses . 10SANS 1700-9-1:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .IS

14、O 4762:2004(E)iv ISO 2004 All rights reservedForewordISO (the International Organization for Standardization) is a worldwide federation of national standards bodies(ISO member bodies). The work of preparing International Standards is normally carried out through ISOtechnical committees. Each member

15、body interested in a subject for which a technical committee has beenestablished has the right to be represented on that committee. International organizations, governmental andnon-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the InternationalElectrote

16、chnical Commission (IEC) on all matters of electrotechnical standardization.International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.The main task of technical committees is to prepare International Standards. Draft International Standardsadopted by th

17、e technical committees are circulated to the member bodies for voting. Publication as anInternational Standard requires approval by at least 75 % of the member bodies casting a vote.Attention is drawn to the possibility that some of the elements of this document may be the subject of patentrights. I

18、SO shall not be held responsible for identifying any or all such patent rights.ISO 4762 was prepared by Technical Committee ISO/TC 2, Fasteners.This fourth edition cancels and replaces the third edition (ISO 4762:1997), which has been technically revised.SANS 1700-9-1:2008This s tandard may only be

19、used and printed by approved subscription and freemailing clients of the SABS .INTERNATIONAL STANDARD ISO 4762:2004(E) ISO 2004 All rights reserved 1Hexagon socket head cap screws1ScopeThis International Standard specifies the characteristics of hexagon socket head cap screws with coarse pitchthread

20、 from M1,6 up to and including M64 and product grade A.For approximate masses of screws see Annex A.If, in special cases, specifications other than those listed in this International Standard are required, they shouldbe selected from existing International Standards, e.g ISO 261, ISO 888, ISO 898-1,

21、 ISO 965-2. ISO 3506-1,ISO 8839 and ISO 4759-1.2 Normative referencesThe following referenced documents are indispensable for the application of this document. For datedreferences, only the edition cited applies. For undated references, the latest edition of the referenced document(including any ame

22、ndments) applies.ISO 225, Fasteners Bolts, screws, studs and nuts Symbols and designations of dimensionsISO 261, ISO general-purpose metric screw threads General planISO 888, Bolts, screws and studs Nominal lengths, and thread lengths for general purpose boltsISO 898-1, Mechanical properties of fast

23、eners made of carbon steel and alloy steel Part 1: Bolts, screws andstudsISO 965-2, ISO general purpose metric screw threads Tolerances Part 2: Limits of sizes for generalpurpose external and internal screw threads Medium qualityISO 965-3, ISO general purpose metric screw threads Tolerances Part 3:

24、Deviations for constructionalscrew threadsISO 3269, Fasteners Acceptance inspectionISO 3506-1, Mechanical properties of corrosion-resistant stainless-steel fasteners Part 1: Bolts, screws andstudsISO 4042, Fasteners Electroplated coatingsISO 4753, Fasteners Ends of parts with external ISO metric thr

25、eadISO 4759-1, Tolerances for fasteners Part 1: Bolts, screws, studs and nuts Product grades A, B and CISO 6157-1, Fasteners Surface discontinuities Part 1: Bolts, screws and studs for general requirementsISO 6157-3, Fasteners Surface discontinuities Part 3: Bolts, screws and studs for special requi

26、rementsISO 8839, Mechanical properties of fasteners Bolts, screws, studs and nuts made of non-ferrous metalsISO 8992, Fasteners General requirements for bolts, screws, studs and nutsSANS 1700-9-1:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the

27、SABS .ISO 4762:2004(E)2 ISO 2004 All rights reservedISO 10683, Fasteners Non-electrolytically applied zinc flake coatingsISO 23429, Gauging of hexagon sockets3 DimensionsSee Figure 1 and Table 1.Symbols and designations of dimensions are defined in ISO 225.Maximum underhead fillet, see Table 1Figure

28、 1lf, max= 1,7 rmaxrmax=da, maxds, max2rminSANS 1700-9-1:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 4762:2004(E) ISO 2004 All rights reserved 3Permissible alternative form of socket Top and bottom edge opf the headFor broached so

29、ckets which are at the maximum limitof size the overcut resulting from drilling shall notexceed 1/3 of the length of any flat of the socket whichis .aA slight rounding or countersink at the mouth of the socket is permissible.bPoint chamfered or for sizes M4 and below “as rolled” according to ISO 475

30、3.cIncomplete thread .dapplies if values of are specified.eTop edge of head may be rounded or chamfered as shown at the option of the manufacturer.fBottom edge of head may be rounded or chamfered to but in every case shall be free from burrs.Figure 1 (continued)e/2u lessorequalslant 2 Pdsls, mindwSA

31、NS 1700-9-1:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 4762:2004(E)4 ISO 2004 All rights reservedTable1DimensionsDimensionsin millimetresThread()M1,6M2M2,5M3M4M5M6M8M10M12a0,350,40,450,50,70,811,251,51,75bref.15161718202224283236

32、max.c3,003,804,505,507,008,5010,0013,0016,0018,00max.d3,143,984,685,687,228,7210,2213,2716,2718,27min.2,863,624,325,326,788,289,7812,7315,7317,73max.22,63,13,64,75,76,89,211,213,7max.1,602,002,503,004,005,006,008,0010,0012,00min.1,461,862,362,863,824,825,827,789,7811,73e,fmin.1,7331,7332,3032,8733,4

33、434,5835,7236,8639,14911,429max0,340,510,510,510,60,60,681,021,021,45max.1,602,002,503,004,005,006,08,0010,0012,00min.1,461,862,362,863,824,825,77,649,6411,57min.0,10,10,10,10,20,20,250,40,40,6fnom.1,51,522,53456810max.1,581,582,082,583,084,0955,146,148,17510,175min.1,521,522,022,523,024,0205,026,02

34、8,02510,025min.0,711,11,322,53456max.0,160,20,250,30,40,50,60,811,2min2,723,484,185,076,538,039,3812,3315,3317,23min.0,550,550,851,151,41,92,33,344,8gShanklength and grip length nom.min.max.min.max.min.max.min.max.min.max.min.max.min.max.min.max.min.max.min.max.min.max.2,52,32,732,83,243,764,2454,76

35、5,2465,766,2487,718,29109,7110,291211,6512,35dPb dkdadselfk r st vdwwllslglslglslglslglslglslglslglslglslglslglslgSANS 1700-9-1:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 4762:2004(E) ISO 2004 All rights reserved 51615,6516,35201

36、9,5820,42242524,5825,425,7584,573029,5830,429,5126,510483534,535,511,5159136114039,540,516,520141811165,75124544,545,51923162110,75175,5135049,550,52428212615,752210,5185554,455,6263120,752715,52310,25196059,460,6313625,753220,52815,25246564,465,630,753725,53320,25297069,470,635,754230,53825,2534807

37、9,480,645,755240,54835,25449089,390,750,55845,255410099,3100,760,56855,2564110109,3110,765,2574120119,3120,775,2584130129,2130,8140139,2140,8150149,2150,8160159,2160,8180179,2180,8200199,075200,925220219,075220,925240239,075240,925260258,95261,05280278,95281,05300298,95301,05Table1Dimensions(continu

38、ed)SANS 1700-9-1:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 4762:2004(E)6 ISO 2004 All rights reservedDimensionsin millimetresThread()(M14)hM16M20M24M30M36M42M48M56M64a222,533,544,555,56bref.40445260728496108124140max.c21,0024,00

39、30,0036,0045,0054,0063,0072,0084,0096,00max.d21,3324,3330,3336,3945,3954,4663,4672,4684,5496,54min.20,6723,6729,6735,6144,6153,5462,5471,5483,4695,46max.15,717,722,426,433,439,445,652,66371max.14,0016,0020,0024,0030,0036,0042,0048,0056,0064,00min.13,7315,7319,6723,6729,6735,6141,6147,6155,5463,54e,f

40、min.13,71615,99619,43721,73425,15430,85436,57141,13146,83152,531max1,451,452,042,042,892,893,063,915,955,95max.14,0016,0020,0024,0030,0036,0042,0048,0056,0064,00min.13,5715,5719,4823,4829,4835,3841,3847,3855,2663,26min.0,60,60,80,8111,21,622fnom.12141719222732364146max.12,21214,21217,2319,27522,2752

41、7,27532,3336,3341,3346,33min.12,03214,03217,0519,06522,06527,06532,0836,0841,0846,08min.78101215,51924283438max.1,41,622,433,64,24,85,66,4min20,1723,1728,8734,8143,6152,5461,3470,3482,2694,26min.5,86,88,610,413,115,316,317,51922gShanklength and grip length nom.min.max.min.max.min.max.min.max.min.max

42、.min.max.min.max.min.max.min.max.min.max.min.max.2,52,32,732,83,243,764,2454,765,2465,766,2487,718,29109,7110,291211,6512,35Table1Dimensions(continued)dPb dkdadselfk r st vdwwllslglslglslglslglslglslglslglslglslglslglslgSANS 1700-9-1:2008This s tandard may only be used and printed by approved subscr

43、iption and freemailing clients of the SABS .ISO 4762:2004(E) ISO 2004 All rights reserved 71615,6516,352019,5820,422524,5825,423029,5830,423534,535,54039,540,54544,545,55049,550,55554,455,66059,460,610206564,465,6152511217069,470,6203016268079,480,63040263615,5289089,390,74050364625,538153010099,310

44、0,75060465635,5482540110109,3110,76070566645,558355020,538120119,3120,77080667655,568456030,5481636130129,2130,88090768665,578557040,5582646140139,2140,890100869675,588658050,568365621,544150149,2150,89610685,598759060,578466631,554160159,2160,810611695,51088510070,588567641,5642752180179,2180,8115,

45、512810512090,5108769661,584477228,556200199,075200,925135,5148125140110,51289611681,5104679248,5763060220219,075220,925101,51248711268,5965080240239,075240,925121,515510713288,511670100260258,95261,05141,5164127152108,513690120280278,95281,05161,5184147172128,5156110140300298,95301,05181,52041671921

46、48,5176130160Table1Dimensions(continued)SANS 1700-9-1:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 4762:2004(E)8 ISO 2004 All rights reservedais the pitch ofthe thread.bFor lengths between the bold stepped linesin the unshaded area

47、.cFor plain heads.dFor knurled heads.e fCombined gauging ofsocketdimensions and ,see ISO23429.gThe range ofcommercial lengths is between the bold stepped lines.Lengths in the shaded area are threaded to the head within .Lengths belowthe shaded area have values ofand in accordance with the following

48、formulae:hThe size in bracketsshould be avoided ifpossible.Table1Dimensions(continued)P emin=1,14smines3Plglslg,max=lnombls,min=lg,max5PSANS 1700-9-1:2008This s tandard may only be used and printed by approved subscription and freemailing clients of the SABS .ISO 4762:2004(E) ISO 2004 All rights res

49、erved 94 Requirements and reference International StandardsSee Table 2.5 DesignationEXAMPLE A hexagon socket head cap screw with thread M5, nominal length and property class 12.9 isdesigned as follows:Hexagon socket head cap screw ISO 4762-M5 20-12.9Table 2 Requirements and reference International StandardsMaterials Steel Stainless steel Non-ferrous metalGeneral requirementsInternational StandardISO 8992ThreadTolerances 5g6g for property class 12.9; for other property classes: 6