SANS 1360-4-2008 Size designation of clothes Part 4 Gloves《服装的尺码标示 第4部分 手套》.pdf

《SANS 1360-4-2008 Size designation of clothes Part 4 Gloves《服装的尺码标示 第4部分 手套》.pdf》由会员分享，可在线阅读，更多相关《SANS 1360-4-2008 Size designation of clothes Part 4 Gloves《服装的尺码标示 第4部分 手套》.pdf（9页珍藏版）》请在麦多课文档分享上搜索。

1、 Collection of SANS standards in electronic format (PDF) 1. Copyright This standard is available to staff members of companies that have subscribed to the complete collection of SANS standards in accordance with a formal copyright agreement. This document may reside on a CENTRAL FILE SERVER or INTRA

2、NET SYSTEM only. Unless specific permission has been granted, this document MAY NOT be sent or given to staff members from other companies or organizations. Doing so would constitute a VIOLATION of SABS copyright rules. 2. Indemnity The South African Bureau of Standards accepts no liability for any

3、damage whatsoever than may result from the use of this material or the information contain therein, irrespective of the cause and quantum thereof. ISBN 978-0-626-21170-7 SANS 1360-4:2008Edition 1.2Any reference to SABS 1360-4 is deemedto be a reference to this standard(Government Notice No. 1373 of

4、8 November 2002)SOUTH AFRICAN NATIONAL STANDARD Size designation of clothes Part 4: Gloves Published by Standards South Africa 1 dr lategan road groenkloof private bag x191 pretoria 0001 tel: 012 428 7911 fax: 012 344 1568 international code + 27 12 www.stansa.co.za Standards South Africa SANS 1360-

5、4:2008 Edition 1.2 Table of changes Change No. Date Scope Amdt 1 1984 Amended to change its category from a SABS standard specification to a SABS specification. Amdt 2 2008 Amended to change the designation of SABS standards to SANS standards, with no technical changes. Foreword This South African s

6、tandard was approved by National Committee StanSA SC 5110.05A, Clothing and made-up articles Clothing, in accordance with procedures of Standards South Africa, in compliance with annex 3 of the WTO/TBT agreement. This document was published in March 2008. This document supersedes SABS 1360-4:1982 (e

7、dition 1). Preface This part of the specification has been prepared under the direction of the SABS Clothing Committee. It is, in technical content, identical to ISO 4418. The specification is one of a series which deals essentially with the size designation of clothes, and is not directly concerned

8、 with sizing systems as such. The primary aim of this specification is, as in the other specifications in the series, to establish a size designation system that is based on body measurements, and that in this case indicates (in a simple, direct, and meaningful manner) the size of the hands of the p

9、erson that a glove is intended to fit. Provided that the size of the persons hands (as indicated by the appropriate dimensions) has been accurately determined, this system will facilitate the choice of gloves that fit. Choice of glove measurements is normally left to the designer and the manufacture

10、rs, who are concerned with the style, cut, and other fashion elements. SANS 1360-4:2008 Edition 1.2 1 Contents Page Foreword Preface 1 Scope . 3 2 Definitions 3 3 Control dimensions 3 4 Size designation . 3 5 Labelling . 4 Appendix A Applicable standards 6 SANS 1360-4:2008 Edition 1.2 2 This page is

11、 intentionally left blank SANS 1360-4:2008 Edition 1.2 3 Size designation of clothes Part 4: Gloves 1 Scope 1.1 This part of the specification establishes a system of designating the size of gloves. Both the control dimensions on which the size designation system is based, and the method of indicati

12、ng the size designation on glove labels, are specified. NOTE The standards referred to in this part of the specification are listed in appendix A. 2 Definitions 2.1 For the purposes of this part of the specification the relevant definitions given in SANS 10184 shall apply. 3 Control dimensions 3.1 T

13、he control dimensions shall be as follows: a) hand girth at knuckles; and b) hand length. 4 Size designation 4.1 General The size designation of gloves shall comprise the control dimensions (see 3.1), in centimetres, of the intended wearer of the gloves. The numerical values of those dimensions shal

14、l be given in the order given in 3.1 and shall, preferably, be preceded by the words “hand girth“ and “hand length“. NOTE The above requirements shall not preclude the use, in exceptional instances, of a) size designations comprising only one of the applicable control dimensions; b) size designation

15、s shown as a range by stating the minimum and maximum control dimensions separated by an oblique stroke or a hyphen. SANS 1360-4:2008 Edition 1.2 4 4.2 Glove measurements Glove measurements shall not be incorporated in the size designation but, where considered of value, they may be indicated separa

16、tely (see 5.3). 5 Labelling 5.1 Method The size designation of the gloves shall be indicated clearly, conspicuously, and in plainly legible form on a label, or on a swing ticket, or on both. Numerals shall, in all cases, be readily discernible. 5.2 Attachment The label or swing ticket shall be secur

17、ely attached to the gloves in a position where it is easily readable. 5.3 Additional information Information additional to the size designation may be separately indicated on the label, or on the swing ticket, or on both, provided that it does not in any way reduce the prominence and conspicuousness

18、 of the size designation. Such additional information may include a size code number, hand measurement, or glove measurement considered to constitute useful information. 5.4 Examples of labels The examples of labels given in figure 1 illustrate methods of labelling that range from the simple indicat

19、ion of the relevant control dimensions to more elaborate forms that provide additional information, such as a glove measurement or a size code number. Where the size designation is supplemented by a size code number, separation of the two, as illustrated, renders the size code number recognizable as

20、 being part of a system of size designation adopted for a limited population group only. SANS 1360-4:2008 Edition 1.2 5 a) Mans glove Hand girth/hand length 23/21 b) Childs stretch glove Hand girth 12-16 Garment length 11-15 c) Womans evening glove Hand girth 16 Han length 14 Size code 61)Shoulder l

21、ength (20 BL) Figure 1 Examples of labels for gloves 1) Example of additional information included in accordance with 5.3. SANS 1360-4:2008 Edition 1.2 6 Appendix A2)Applicable standards Reference is made to the latest issues of the following standards: ISO 4418, Size designation of clothes Gloves. SANS 10184 (SABS 0184), Definitions for and measurement of body dimensions. Standards South Africa 2) The information in the appendices is additional to that in this part of the specification and has been included purely for amplification and guidance.