SAE USCAR-37-2008 High Voltage Connector Performance Supplement to SAE USCAR-2《高压连接器性能 SAE USCAR-2的补充件》.pdf

《SAE USCAR-37-2008 High Voltage Connector Performance Supplement to SAE USCAR-2《高压连接器性能 SAE USCAR-2的补充件》.pdf》由会员分享，可在线阅读，更多相关《SAE USCAR-37-2008 High Voltage Connector Performance Supplement to SAE USCAR-2《高压连接器性能 SAE USCAR-2的补充件》.pdf（28页珍藏版）》请在麦多课文档分享上搜索。

1、 High Voltage Connector Performance Supplement to SAE/USCAR-2 SAE/USCAR-37 August 2008 ISBN: 978-0-7680-2098-4 _ The research data, analysis, conclusion, opinions and other contents of this document are solely the product of the authors. Neither the SAE International (SAE) nor the United States Coun

2、cil for Automotive Research (USCAR) certifies the compliance of any products with the requirements of nor makes any representations as to the accuracy of the contents of this document nor to its applicability for purpose. It is the sole responsibility of the user of this document to determine whethe

3、r or not it is applicable for their purposes. Copyright 2008 USCAR Printed in U.S.A. All rights reserved. QUESTIONS REGARDING THIS DOCUMENT: (248) 273-2470 FAX (248) 273-2494 TO PLACE A DOCUMENT ORDER: (724) 776-4970 FAX (724) 776-0790 SAE/USCAR-37 Issued 2008-08 HIGH VOLTAGE CONNECTOR PERFORMANCE S

4、UPPLEMENT TO SAE/USCAR-2 TABLE OF CONTENTS 1. SCOPE. 2 2. OUTLINE & GLOSSARY OF TERMS. 3 3. REFERENCED DOCUMENTS REQUIRED 3 4. GENERAL REQUIREMENTS AND INFORMATION 5 5. TEST & ACCEPTANCE REQUIREMENTS 5 5.1 General 5 5.2 Terminal Mechanical 9 5.3 Terminal Electrical16 5.4 Connector Mechanical .16 5.5

5、 Connector Electrical.18 5.6 Connector or Terminal Environmental.19 5.7 Special Tests.20 5.8 Severe Duty Tests.21 5.9 Test Sequence 21 APPENDIX A: DEFINITIONS .26 APPENDIX B: GLOSSARY OF TERMS26 APPENDIX C: TESTS RECOMMENDED FOR NEW TOOLING, TOOL TRANSFER, OR MATERIAL CHANGE.26 APPENDIX D: TESTS FOR

6、 NEW/EXISTING TERMINAL OR CONNECTOR DESIGNS 26 APPENDIX E: SOURCE LIST26 APPENDIX F: DESIGN NOTES.26 APPENDIX G: REVISIONS 26 SAE/USCAR-37 Issued 2008-08 HIGH VOLTAGE CONNECTOR PERFORMANCE SUPPLEMENT TO SAE/USCAR-2 - 2 - *WARNING* No electrical connector, terminal, or related component may be repres

7、ented as having met USCAR/EWCAP specifications unless conformance to all applicable requirements of this specification have been verified and documented. All required verification and documentation must be done by the supplier of the part or parts. If testing is performed by another source, it does

8、not relieve the primary supplier of responsibility for documentation of all test results and for verification that all samples tested met all applicable Acceptance Criteria. 1. SCOPE Procedures included within this specification supplement are, when used in conjunction with SAE/USCAR 2, intended to

9、cover performance testing at all phases of development, production, and field analysis of electrical terminals, connectors, and components that constitute the electrical connection systems in high voltage (60600V) road vehicle applications. These procedures are applicable to terminals used for In-Li

10、ne, Header, and Device Connector systems with and without Shorting Bars. This supplement applies to both sealed and unsealed connection systems. IMPORTANT NOTICE: In any intended vehicle application, if the products covered by this specification are, or may be, subjected to conditions beyond those d

11、escribed in this document, they must pass special tests simulating the actual conditions to be encountered before they can be considered acceptable for actual vehicle application. By way of example only, this includes products that may be subjected to conditions beyond the extremes of Classes as def

12、ined in Tables 5.1.4.1, 5.1.4.5 or those that may be subjected to shock or vibration in the un-sprung portions of a vehicle, such as the wheel hub. Products certified by their supplier as having passed specific applicable portions of this specification are not to be used in applications where condit

13、ions may exceed those for which the product has been satisfactorily tested. The Authorized Person is the final authority as to what tests are to be performed on his or her parts and for what purpose these tests are required. He or she is also the final authority for resolving any questions related t

14、o testing to this specification and to authorizing any deviations to the equipment or procedures contained in this specification. Any such deviation must be documented and included in the final test report. Guidance as to the recommended tests for selected purposes is given in the charts in SAE/USCA

15、R 2 Appendix C and D. In the absence of contrary direction from the Authorized Person in the test request/order, all electrical connectors and their associated terminals and other components are required to meet all applicable portions of SAE/USCAR 2 and this supplement document with the following e

16、xception: Specific tests that are not required or additional test requirements as specified in any document in the hierarchy of Section 3.0. SAE/USCAR-37 Issued 2008-08 HIGH VOLTAGE CONNECTOR PERFORMANCE SUPPLEMENT TO SAE/USCAR-2 - 3 - 2. OUTLINE & GLOSSARY OF TERMS 2.1 General Diagrams are provided

17、 where necessary to clarify the details of the various test procedures. The tests in each section must be performed in the order given unless otherwise specified in the test request/order. Construction details for selected test fixtures and equipment are provided in this specification. A glossary of

18、 terms is provided in USCAR 2, Appendix B. Terms defined in the definitions or glossary are capitalized (i.e. Room Temperature, Steady State, PLR, etc.). A list of definitions is provided in USCAR 2, Appendix A. 3. REFERENCED DOCUMENTS 3.1 Document Hierarchy In the event there is a conflict between

19、performance specifications, part drawings, and other related standards or specifications, the requirements shall be prioritized as follows: 1st- Applicable FMVSS requirements and other applicable state and Federal requirements. 2nd- Applicable part drawings 3rd- Applicable product design specificati

20、on(s). 4th- Automotive Industry Action Group (AIAG) Production Part Approval Process (PPAP) 5th- Applicable USCAR/EWCAP performance specifications 6th- Other applicable standards and specifications 3.2 Part Drawing The part drawing for each connection system component should contain or reference: Al

21、l dimensional requirements (which must be in GD&T format). Performance requirements. Component part number. Reference to applicable portions of this specification. The quantity and part number of terminals used. The typical mating connector. Classes per tables 5.1.4.1 5.1.4.5 for which the part is i

22、ntended or has been successfully tested. 3.3 Product Design Specification The product design specification may or may not be an integral part of the part drawing. Instructions must be included in the product design specification for any special tests required for the associated part and for any exce

23、ptions or modifications to the general specifications and requirements in this document. SAE/USCAR-37 Issued 2008-08 HIGH VOLTAGE CONNECTOR PERFORMANCE SUPPLEMENT TO SAE/USCAR-2 - 4 - 3.4 Test Request/Order 3.4.1 Samples, Test Type and Special Tests The laboratory test request/order shall provide lo

24、cation and documentation of test samples, identify the type of test to be performed (development, validation, special purpose, etc.) and describe any special tests that are not a part of this specification. Any required revisions to, or deviations from any tests in this specification must include de

25、tailed instructions for each change. 3.4.2 Test Request/Order Instructions Instructions must be included in the test request/order concerning applicable tests and the order in which the tests are to be performed if different than outlined by this specification. 3.4.3 Performance and Durability Test

26、Instructions Instructions must be given in the test request/order concerning limits for performance and durability tests, including definition of the conditions under which those limits apply, if they are different than outlined in this specification. 3.4.4 Development Tests Development tests are fr

27、equently used to evaluate specific areas of the design. They are tools for evaluating design alternatives, proposed improvements, cost reduction proposals, or determining root causes of field problems. 3.4.5 Validation Tests Validation tests or sample approval tests are acceptance type tests. Consid

28、eration must be given to the inherent repeatability or subjectivity of certain tests outlined by this specification before designating it as a validation or compliance test. 3.4.6 Special Purpose Tests Portions of this specification may be useful for special purpose testing. For example, verifying a

29、 process or material change may, in the judgment of the Authorized Person, require only one or two specific tests, or a portion of a test, to verify that no adverse consequence resulted from the change. Any portion of a test or any combination of tests contained in this specification may be used ind

30、ividually or may be combined with other testing, described outside this specification, in any phase of product development, production testing, or analysis of parts from the field. 3.5 Other Referenced Documents SAE/USCAR 2: Performance specification for automotive electrical connector systems SAE/U

31、SCAR-21: Performance Specification for Cable-to-Terminal Electrical Crimps. SAE/USCAR 25 Electrical Connector Assembly Ergonomic Design Criteria. IEC 62153 part 4-7 ASTM B117 SAE/USCAR-37 Issued 2008-08 HIGH VOLTAGE CONNECTOR PERFORMANCE SUPPLEMENT TO SAE/USCAR-2 - 5 - 4. GENERAL REQUIREMENTS AND IN

32、FORMATION See USCAR 2 5. TEST & ACCEPTANCE REQUIREMENTS 5.1 General The tests detailed in this specification are qualitative in nature and are not expected to stress any part beyond its anticipated application limit, except where tests to failure are specified. 5.1.1 Performance requirements Connect

33、ion systems must meet all performance test requirements for the appropriate Class as listed in Tables 5.1.4.15.1.4.5 5.1.2 Dimensional characteristics Part construction shall conform to the dimensions, shape, and detail attributes specified on the latest revision of the applicable part drawing(s). 5

34、.1.3 Material Characteristics Parts are intended to be in their “as furnished for vehicle assembly“ condition when testing begins, unless specific instructions as to any pre-test “conditioning“ are contained in the test request/order. For example, electrical terminals typically have residual die lub

35、ricant on them when finally assembled into a vehicle. This same condition must prevail for test samples unless part cleaning is specified in the Test Request/Order. All material used in each test sample shall conform to the material specifications shown on the latest revision of the applicable part

36、drawing(s). The material hardness specified for electrical terminals refers to the blank strip material and not the finished product because the terminal manufacturing process can modify the hardness values. 5.1.4 Classifications Connection systems shall be assigned a class designation from the foll

37、owing categories. 5.1.4.1 Temperature classifications Components to be tested must be assigned a class from the table below according to the expected environment in their intended vehicle application. “Rise“ is defined as the temperature rise due to electrical heating caused by the maximum Steady St

38、ate current flow expected for the component under test. Care must be taken to ensure that the conductor and insulation selected for the application or any test will itself withstand the maximum temperature for the class selected without exceeding the conductor manufacturers maximum temperature recom

39、mendations. SAE/USCAR-37 Issued 2008-08 HIGH VOLTAGE CONNECTOR PERFORMANCE SUPPLEMENT TO SAE/USCAR-2 - 6 - Note also that terminals packaged such that they are surrounded by other terminals will dissipate heat more slowly, and thus experience a higher temperature “rise“ with the same current flow, t

40、han terminals located on the periphery of a connector. See USCAR 2 Appendix F (design notes) When “Maximum Temperature“ is mentioned with respect to Table 5.1.4.1, the highest ambient temperature in the right column, “Ambient Temperature Range“ is to be used unless otherwise specified. If not specif

41、ied in the Test Request/Order, the Authorized Person is expected to select the appropriate Temperature Classification. Considering the cost of testing and the time it takes, it generally will be best to qualify a given terminal and connector system to the highest possible Temperature Classification.

42、 Class Ambient Temperature Range 1 -40oC to + 85oC 2 -40oC to +100oC 3 -40oC to +125oC 4 -40oC to +150o C 5 -40oC to +175o C Table 5.1.4.1: Component Temperature Classes 5.1.4.2 Sealing classifications Components to be tested must be assigned a class from the table below according to the expected en

43、vironment in their intended vehicle application. S1: Unsealed connectors are suitable for use in passenger compartment or other dry areas on a vehicle such as the trunk. S2: Sealed connectors must meet the all requirements of 5.9.7, the Sealed connector environmental test sequence. S3: Sealed (plus

44、pressure spray) connectors must meet all of the requirements of 5.9.7 plus the requirements of 5.8.1, High pressure spray. Class Application Type S1 Unsealed S2 Sealed S3 Sealed plus pressure spray Table 5.1.4.2: Component Sealing Classes SAE/USCAR-37 Issued 2008-08 HIGH VOLTAGE CONNECTOR PERFORMANC

45、E SUPPLEMENT TO SAE/USCAR-2 - 7 - 5.1.4.3 Vibration Classification Components to be tested must be assigned a class from the table below according to the expected location in their intended vehicle application. V1: Components intended for use on sprung portions of the vehicle and not coupled to the

46、engine shall be tested to vibration profile figure 5.4.6.3 E. and meet the requirements of 5.4.6.4. V2: Components intended for use coupled to the engine shall be tested to vibration profile figure 5.4.6.3.D and meet the requirements of 5.4.6.4. V3: Components intended for use in extreme vibration l

47、evels shall be tested to vibration profile figures 5.8.2.3.B and 5.8.2.3.C. and meet the requirements of 5.4.6.4. Class Typical application V1 Components on sprung portions of vehicle not coupled to Engine. V2 Components coupled to Engine. V3 Components subject to severe vibration. Table 5.1.4.3 Com

48、ponent Vibration Classes 5.1.4.4 Ergonomic Classification Refer to SAE/USCAR 25 for requirements necessary to assign an Ergonomic class to the component under test. This class designation shall be documented in the test plan and listed on the component drawing. 5.1.4.5 Connector mating cycle classif

49、ication Connection systems must be assigned a mating cycle classification based on the application descriptions in Table 5.1.4.5. This classification designation shall be documented in the test plan, test report, and identified on the component drawing. Class Typical application M1 In-lines and headers not normally disconnected for service. These are permanent connection systems and are not expected to be disconnected after the