SAE USCAR-30-2006 Performance Specification for Automotive Universal Serial Bus (USB) Connection System《汽车通用串行总线(USB)连接系统的性能规范》.pdf

《SAE USCAR-30-2006 Performance Specification for Automotive Universal Serial Bus (USB) Connection System《汽车通用串行总线(USB)连接系统的性能规范》.pdf》由会员分享，可在线阅读，更多相关《SAE USCAR-30-2006 Performance Specification for Automotive Universal Serial Bus (USB) Connection System《汽车通用串行总线(USB)连接系统的性能规范》.pdf（42页珍藏版）》请在麦多课文档分享上搜索。

1、 Performance Specification for AutomotiveSAE/USCAR-30November 2006Universal Serial Bus (USB) Connection SystemISBN-10: 0-7680-1845-5 ISBN-13: 978-0-7680-1845-5 PERFORMANCE SPECIFICATION FOR AUTOMOTIVE UNIVERSAL SERIAL BUS (USB) CONNECTION SYSTEM The research data, analysis, conclusion, opinions and

2、other contents of this document are solely the product of the authors. Neither the Society of Automotive Engineers, Inc. (SAE) nor the United States Council for Automotive Research (USCAR) certifies the compliance of any products with the requirements of nor makes any representations as to the accur

3、acy of the contents of this document nor to its applicability for purpose. It is the sole responsibility of the user of this document to determine whether or not it is applicable for their purposes. Copyright 2006, USCAR All rights reserved. Printed in U.S.A. Issued 2006-11 SAE/USCAR-30 QUESTIONS RE

4、GARDING THIS DOCUMENT: (724) 772-8518 FAX (724) 776-3036 TO PLACE A DOCUMENT ORDER: (724) 776-4970 FAX (724) 776-0790 TABLE OF CONTENTS 1 SCOPE.3 2 OUTLINE & GLOSSARY OF TERMS.4 2.1 GENERAL 4 3 REFERENCED DOCUMENTS REQUIRED .4 3.1 DOCUMENT HIERARCHY .4 3.2 PART DRAWING 5 3.3 PRODUCT DESIGN SPECIFICA

5、TION.5 3.4 TEST REQUEST/ORDER .5 3.4.1 Samples, Test Type and Special Tests5 3.4.2 Test Request/Order Instructions 5 3.4.3 Performance and Durability Test Instructions 5 3.4.4 Development Tests.5 3.4.5 Validation Tests .6 3.4.6 Special Purpose Tests6 3.5 OTHER REFERENCED DOCUMENTS6 4 GENERAL REQUIRE

6、MENTS.6 4.1 RECORD RETENTION .6 4.2 SAMPLE DOCUMENTATION .6 4.3 SAMPLE SIZE.6 4.4 DEFAULT TEST TOLERANCES7 4.5 TEST DEFAULT CONDITIONS .7 4.6 EQUIPMENT.7 4.7 MEASUREMENT RESOLUTION9 4.8 TEST REPEATABILITY & CALIBRATION.9 4.9 CONFORMANCE DETERMINATION .9 4.10 DISPOSITION OF SAMPLES .9 4.11 PART ENDUR

7、ANCE 10 SAE/USCAR-30 PERFORMANCE SPECIFICATION FOR AUTOMOTIVE UNIVERSAL SERIAL BUS (USB) CONNECTION SYSTEM - 2 - 5 TEST & ACCEPTANCE REQUIREMENTS .10 5.1 GENERAL 10 5.1.1 Performance Requirements .10 5.1.2 Dimensional Characteristics .10 5.1.3 Material Characteristics10 5.1.4 Temperature Classificat

8、ions10 5.1.5 Testing Headers & Direct Connect Components.11 5.1.6 Sample Preparation (LLCR)11 5.1.7 Connector Cycling.12 5.1.8 Visual Inspection .13 5.1.9 Circuit Continuity Monitoring.14 5.2 CABLE ASSEMBLY - MECHANICAL TESTS .15 5.2.1 Connector Connector Mating/Unmating Force .15 5.2.2 Cable Flex19

9、 5.2.3 Vibration/Mechanical Shock .19 5.2.4 Connector-to-Connector Audible Click- Non Consumer Interface Only.20 5.2.5 Connector Assembly Drop Test .21 5.2.6 Cable Pull-Out (Retention)21 5.2.7 Polarization Feature Effectiveness (Non-consumer Interface Only).22 5.3 CABLE ASSEMBLY - ELECTRICAL TESTS .

10、22 5.3.1 Low Level Contact Resistance .22 5.3.2 Insulation (Isolation) Resistance .24 5.4 RF TESTS 24 5.4.1 Cable Assembly Impedance .24 5.4.2 Cable Assembly Propagation Delay25 5.4.3 Cable Assembly Propagation Delay Skew.25 5.4.4 Cable Assembly Attenuation 26 5.4.5 Cable Assembly Shielding Effectiv

11、eness26 5.5 CONNECTOR ENVIRONMENTAL TESTS 27 5.5.1 Thermal Shock .27 5.5.2 Temperature/Humidity Cycling .27 5.5.3 High Temperature Exposure28 6 TEST SEQUENCE .29 6.1.1 General Notes29 APPENDIX A: DEFINITIONS.34 APPENDIX B: GLOSSARY OF TERMS37 APPENDIX C: TESTS RECOMMENDED FOR NEW TOOLING, TOOL TRANS

12、FER, OR MATERIAL CHANGES TO NON CONSUMER INTERFACE CONNECTIONS .38 APPENDIX D: REVISIONS 40 Issued 2006-11 - 3 - *WARNING* No electrical connector, terminal, or related USB component may be represented as having met USCAR/EWCAP specifications unless conformance to all applicable requirements of this

13、 specification have been verified and documented. All required verification and documentation must be done by the supplier of the part or parts. If testing is performed by another source, it does not relieve the primary supplier of responsibility for documentation of all test results and for verific

14、ation that all samples tested met all applicable Acceptance Criteria. See section 4.3. 1 SCOPE Procedures included within this specification are intended to cover performance testing at all phases of development, production, and field analysis of any USB cable assemblies and associated connections t

15、hat constitute the electrical connection systems between the consumer peripheral interface and the USB computer source in road vehicle applications. These procedures are only applicable to the USB connector and the cable. Unless otherwise specified, all of the tests listed in this specification are

16、for both consumer and nonconsumer interface connectors. IMPORTANT NOTICE: All suppliers developing an automotive grade USB system must use components that have been validated and approved by an authorized USB testing facility per USB 2.0. In any intended vehicle application, if the products covered

17、by this specification are, or may be, subjected to conditions beyond those described in this document, they must pass special tests simulating the actual conditions to be encountered before they can be considered acceptable for actual vehicle application. Products certified by their supplier as havi

18、ng passed specific applicable portions of this specification are not to be used in applications where conditions may exceed those for which the product has been satisfactorily tested. The high frequency test methods are written for test professionals who are knowledgeable in the electronics field an

19、d are trained to use the referenced equipment. Because the measurement values are heavily influenced by the fixturing and equipment this method cannot describe all of the possible combinations. The major equipment manufacturers provide Application Notes for more in-depth technical description of how

20、 to optimize the use of their equipment. The Authorized Person is the final authority as to what tests are to be performed on his or her parts and for what purpose these tests are required. He or she is also the final authority for resolving any questions related to testing to this specification and

21、 to authorizing any deviations to the equipment or procedures contained in this specification. Any such deviation must be documented and included in the final test report. Guidance as to the recommended tests for selected purposes is given in the charts in Appendix C. In the absence of contrary dire

22、ction from the Authorized Person in the test request/order, all electrical connectors and their associated terminals and other components are required to meet all applicable portions of this document with the following exception: SAE/USCAR-30 PERFORMANCE SPECIFICATION FOR AUTOMOTIVE UNIVERSAL SERIAL

23、 BUS (USB) CONNECTION SYSTEM Issued 2006-11 - 4 - Specific tests that are not required or additional test requirements as specified in any document in the hierarchy of Section 3.1. All suppliers of USB automotive assemblies must use certified USB 2.0 components (ie. USB mini-B receptacle, standard A

24、 stainless steel receptacle or equivalent ruggedized receptacle, mini B plug). For non-consumer interfaces, please refer to the USCAR footprint drawing labeled 999-U-USB-Z01.pdf. The drawing can be found at www.ewcap.uscarteams.org Refer to USB 2.0 website (www.usb.org) for approved supplier list 2

25、OUTLINE & GLOSSARY OF TERMS 2.1 GENERAL Diagrams are provided where necessary to clarify the details of the various test procedures. The tests in each section must be performed in the order given unless otherwise specified in the test request/order. Construction details for selected test fixtures an

26、d equipment are provided in this specification. A glossary of terms is provided in Appendix B. Terms defined in the definitions or glossary are capitalized (i.e. Room Temperature, Steady State, etc.). A list of definitions is provided in Appendix A. 3 REFERENCED DOCUMENTS REQUIRED 3.1 DOCUMENT HIERA

27、RCHY In the event there is a conflict between performance specifications, part drawings, and other related standards or specifications, the requirements shall be prioritized as follows: 1st- Applicable FMVSS requirements and other applicable state and Federal requirements. 2nd - Applicable part draw

28、ings 3rd- Applicable product design specification(s). 4th- Automotive Industry Action Group (AIAG) Production Part Approval Process (PPAP) 5th- Applicable USCAR/EWCAP performance specifications 6th- Universal Serial Bus (USB) Specifications 7th- USB 2.0 8th- Other applicable standards and specificat

29、ions SAE/USCAR-30 PERFORMANCE SPECIFICATION FOR AUTOMOTIVE UNIVERSAL SERIAL BUS (USB) CONNECTION SYSTEM Issued 2006-11 - 5 - 3.2 PART DRAWING The part drawing for each connection system component should contain or reference: All dimensional requirements (which must be in GD&T format). Performance re

30、quirements. Component part number. Reference to applicable portions of this specification. The typical mating connector. Maximum permissible Temperature Class 1 (-40 C to +85 C) (per USCAR-2) 3.3 PRODUCT DESIGN SPECIFICATION The product design specification may or may not be an integral part of the

31、part drawing. Instructions must be included in the product design specification for any special tests required for the associated part and for any exceptions or modifications to the general specifications and requirements in this document. 3.4 TEST REQUEST/ORDER 3.4.1 Samples, Test Type and Special

32、Tests The laboratory test request/order shall provide location and documentation of test samples, identify the type of test to be performed (development, validation, special purpose, etc.) and describe any special tests that are not a part of this specification. Any required revisions to, or deviati

33、ons from any tests in this specification must include detailed instructions for each change. 3.4.2 Test Request/Order Instructions Instructions must be included in the test request/order concerning applicable tests and the order in which the tests are to be performed if different than outlined by th

34、is specification. 3.4.3 Performance and Durability Test Instructions Instructions must be given in the test request/order concerning limits for performance and durability tests, including definition of the conditions under which those limits apply, if they are different than outlined in this specifi

35、cation. 3.4.4 Development Tests Development tests are frequently used to evaluate specific areas of the design. They are tools for evaluating design alternatives, proposed improvements, cost reduction proposals, or determining root causes of field problems. SAE/USCAR-30 PERFORMANCE SPECIFICATION FOR

36、 AUTOMOTIVE UNIVERSAL SERIAL BUS (USB) CONNECTION SYSTEM Issued 2006-11 - 6 - 3.4.5 Validation Tests Validation tests or sample approval tests are acceptance type tests. Consideration must be given to the inherent repeatability or subjectivity of certain tests outlined by this specification before d

37、esignating it as a validation or compliance test. 3.4.6 Special Purpose Tests Portions of this specification may be useful for special purpose testing. For example, verifying a process or material change may, in the judgment of the Authorized Person, require only one or two specific tests, or a port

38、ion of a test, to verify that no adverse consequence resulted from the change. Any portion of a test or any combination of tests contained in this specification may be used individually or may be combined with other testing, described outside this specification, in any phase of product development,

39、production testing, or analysis of parts from the field. 3.5 OTHER REFERENCED DOCUMENTS SAE/USCAR-20: Field Correlated Life Test SAE/USCAR-25: Electrical Connector Assembly Ergonomic Design Criteria AIAG: Measurement Systems Analysis Reference Manual ISO TS16949 IEC 68-2-32 Basic Environmental Test

40、Procedures part 2 USB 2.0: Universal Serial Bus Specification USB Cable and Connector Class Document 4 GENERAL REQUIREMENTS 4.1 RECORD RETENTION The supplier shall maintain a central file for the storage of laboratory reports and calibration records. Such record storage must be in accordance with es

41、tablished ISO TS16949 and AIAG policies and practices. 4.2 SAMPLE DOCUMENTATION All test samples shall be identified in accordance with the requirements of ISO TS16949 and the AIAG PPAP. 4.3 SAMPLE SIZE Minimum sample sizes are given for each test in this specification. A greater number of samples m

42、ay be required by the test request/order. However, no part or device may be represented as having met this specification unless the minimum sample size has been tested and all samples of the group tested have met the applicable Acceptance Criteria for that test. It is never permissible to test a lar

43、ger group, then select the minimum sample size from among those that passed and represent that this specification has been met. SAE/USCAR-30 PERFORMANCE SPECIFICATION FOR AUTOMOTIVE UNIVERSAL SERIAL BUS (USB) CONNECTION SYSTEM Issued 2006-11 - 7 - 4.4 DEFAULT TEST TOLERANCES Default Tolerances, expr

44、essed as a percentage of the nominal value unless otherwise indicated: Temperature = 3oC Voltage = 5% Current = 5% Resistance = 5% Length = 5% Time = 5% Force = 5% Frequency = 5% Relative Humidity = 5% 4.5 TEST DEFAULT CONDITIONS When specific test conditions are not given either in the product desi

45、gn specification, the test request/order or elsewhere in this specification, the following basic conditions shall apply: Room Temperature = 23 5oC Relative Humidity = Ambient 4.6 EQUIPMENT Neither this list nor the list in each test section is all-inclusive. It is meant to highlight specialized equi

46、pment or devices with particular accuracy requirements. Many other items of customary laboratory equipment and supplies will also be required. SAE/USCAR-30 PERFORMANCE SPECIFICATION FOR AUTOMOTIVE UNIVERSAL SERIAL BUS (USB) CONNECTION SYSTEM Issued 2006-11 - 8 - ITEM DESCRIPTION REQUIREMENTS* 1 Micr

47、o-ohmmeter 0-20 mV 0-100 mA Limits the open circuit voltage to 20 mV and limits the current applied to 100 mA. The micro-ohmmeter must also use either offset compensation or current reversal methods to measure resistance 2 Digital Multimeter (DMM) * Capable of measuring the following at an accuracy

48、of 0.5% of full scale: 0-50 Volts DC 0-10 Megohms 3 Insertion/Extraction Force Tester Capable of 1.0% accuracy, full scale 4 Temperature Chamber -40oC to +100oC or as required by Temperature Class 0% to 95% RH 5 Vibration Controller As Required 6 Vibration Table 2640N (600 Lbs.) Sine Force 2200N (50

49、0 Lbs.) RMS Force 7 Megohmeter Accuracy 10N and 70N 5.2.1.4.2 Consumer Interface Only Mating Force shall meet the requirements shown in USB 2.0 Un-mating Force prior to 5000 mating cycles should be collected for reference where applicable Un-mating Force must be 10 Newtons after 5000 mating cycles. SAE/USCAR-30 PERFORMANCE SPECIFICATION FOR AUTOMOTIVE UNIVERSAL SERIAL BUS (USB) CONNECTION SYSTEM Issued 2006-11 - 19 - 5.2.2 Cable Flex 5.2.2.1 Purpose To determine the effectiveness of the cable assembly to withstand strain under rep