SAE J 96-2010 Flashing Warning Lamp for Industrial Equipment《工业设备用闪烁警示灯》.pdf

《SAE J 96-2010 Flashing Warning Lamp for Industrial Equipment《工业设备用闪烁警示灯》.pdf》由会员分享，可在线阅读，更多相关《SAE J 96-2010 Flashing Warning Lamp for Industrial Equipment《工业设备用闪烁警示灯》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、_SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref

2、rom, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2010 SAE International All rights reserved. No part of this publication ma

3、y be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside US

4、A) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/J96_201007SURFACEVEHICLESTANDARDJ96 JUL2010 Issued 1973-05 Revised 2010-07Superseding J96 DEC20

5、05 Flashing Warning Lamp for Industrial Equipment RATIONALEChanges made to this document include: Updating the 4 cd requirement to allow only the outboard projected light if the device is intergraded into the cab or body of the machine.1. SCOPE This SAE Standard covers the general requirements and t

6、he test requirements for a flashing warning lamp for industrial wheeled equipment. 2. REFERENCES 2.1 Applicable Documents The following publications form a part of this specification to the extent specified herein. Unless otherwise indicated, the latest issue of SAE publications shall apply. SAE Pub

7、lications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA), www.sae.org.SAE J567 Light Source Retention System SAE J575 Test Methods and Equipment for Lighting Devices for Use on Vehicles Less

8、 than 2032 mm in Overall WidthSAE J578 Color Specification SAE J588 Turn Signal Lamps for Use on Motor Vehicles Less than 2032 mm in Overall Width SAE J1889 L.E.D. Signal and Marking Lighting Devices 3. DEFINITIONS 3.1 INDUSTRIAL WHEELED EQUIPMENT That class of tractors and associated equipment used

9、 in operations such as landscaping, construction services, loading, digging, grounds keeping, and highway maintenance. SAE J96 Revised JUL2010 Page 2 of 23.2 FLASHING WARNING LAMP A lighted device to indicate both forward and rearward the presence of industrial equipment which normally travel at rat

10、es of speed below that of other traffic. 4. GENERAL REQUIREMENTS 4.1 The lamp shall comply in both the forward and rearward direction with the candela requirements of a turn signal lamp, SAE J588, Table 1. In addition, the lamp shall project at least 4 cd on both sides at 90 degrees to the lamp axis

11、. If the lamp is integrated into the cab or body of the machine, only the out board side of the lamp need meet the minimum 4 cd requirement. 4.2 The color of the light from the warning lamp shall be amber in accordance with SAE J578. 4.3 The lamp shall be flashed at least 60 fpm (flashes per minute)

12、 but not more than 120 fpm when it is operating. 4.4 The effective projected illuminated area measured on a plane at right angles to the axis of the lamp shall not be less than 77.5 mm2(12 in2)4.5 The bulb sockets shall comply with SAE J567. 5. TEST REQUIREMENTS The flashing warning lamp shall be te

13、sted according to the following sections of SAE J575: Lamp Bulbs Laboratory Facilities Samples for Test Vibration Test Moisture Test Dust Test Corrosion Test Photometric Test - All beam candela measurements shall be made with the filament of the signal lamp at least 3 m (10 ft) from the photometer s

14、creen. The lamp axis is the horizontal line through the filament parallel to what would be the longitudinal axis of the vehicle if the lamp were mounted in its normal position on the vehicle. Warpage Test on Devices with Plastic Lenses 6. NOTES 6.1 Marginal Indicia A change bar (l) located in the le

15、ft margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only. PREPARED BY THE OPERATOR PROTECTION TECHNICAL COMMITTEE SC3 LIGHTING AND MARKING