SAE J 1702-2014 Self-Propelled Sweepers Sweep-Ability Performance《自动推进清扫机清扫能力的性能》.pdf

《SAE J 1702-2014 Self-Propelled Sweepers Sweep-Ability Performance《自动推进清扫机清扫能力的性能》.pdf》由会员分享，可在线阅读，更多相关《SAE J 1702-2014 Self-Propelled Sweepers Sweep-Ability Performance《自动推进清扫机清扫能力的性能》.pdf（7页珍藏版）》请在麦多课文档分享上搜索。

1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there

2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2014 SAE International All rights reserved. No part of this p

3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497

4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/J1702_201405 SURFACE VEHICLE STANDARD J1702 MAY2014 Issued 1994-03 Revised 2014-0

5、5 Superseding J1702 NOV2007 Self-Propelled Sweepers Sweep-Ability Performance RATIONALE The document has been revised to update the referenced documents and clarify some statements. 1. SCOPE This SAE Standard establishes a method of disclosing the sweep-ability performance of self-propelled sweepers

6、 that use broom means for sweeping and collection, together with either a mechanical- or pneumatic-conveyance system for the transfer of “sweepings” into a collection hopper. 1.1 Purpose The purpose of this document sets out to describe a test practice for gauging the sweep-ability performance by sw

7、eepers described in SAE J2130-1 together with a format for the presentation of the test results. The document can be used to disclose or compare particular operating performance criteria for similar conditions. 2. REFERENCES 2.1 Applicable Document The following publication forms a part of this spec

8、ification to the extent specified herein. Unless otherwise indicated, the latest issue of SAE publications shall apply. 2.1.1 SAE Publication Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or 724-776-4970 (outside USA),

9、www.sae.org. SAE J2130-1 Identification of Self-Propelled Sweepers and Cleaning Equipment Part 1 Machines with a Gross Vehicle Mass greater than 5000 kg SAE INTERNATIONAL J1702 Revised MAY2014 Page 2 of 7 3. DEFINITIONS 3.1 SWEEPER A self-propelled sweeper is primarily designed to sweep material fro

10、m highways, parking lots, airport complexes, industrial and construction sites, and during road maintenance work. The sweeper may use broom means to dislodge and direct material into a collection mechanism, which may be mechanical, pneumatic, or a combination of both systems to convey the swept mate

11、rial into a collection hopper. 3.2 TEST SITE Level paved area (r3%) on which the sweeping test is conducted. 3.3 TEST MATERIAL Prepared materials used in the sweeping tests. 4. TECHNICAL REQUIREMENTS 4.1 Test Method There are three separate tests - using an assortment of consistent test materials fo

12、r each test. 4.2 Condition of Sweeper Prior to a test, the sweeper shall be set at the normal operational settings according to the manufacturers specification. Brooms and swept material containment curtains, etc., should be in like-new condition. Where the sweeper has variable duties of operation d

13、escribed in its instruction manual, then the sweeper shall be operated at its maximum-duty cycle. These settings shall be stated in the test report. Dust suppression systems if provided shall be active during the test. 4.3 Weather Conditions Weather conditions shall be dry, with a wind speed less th

14、an 20 km/h and such that it does not disturb objects on the test course as depicted in test 3. 4.4 Test Site 4.4.1 Site During the test run, the sweeping brooms (channel(s) or gutter broom(s) shall be directed along the guideline depicted in the test site pattern in 4.4.3. 4.4.2 Site Preparation The

15、 position and pattern of the test material placement zones is shown in the test site pattern in 4.4.3. If the type and sweeping width of the sweeper being assessed lacks sufficient capacity, then the zone size and materials can be varied, in which case full descriptions should be recorded with descr

16、iption of the criteria recorded in the test report. 4.4.3 Test Site Pattern See Figure 1. SAE INTERNATIONAL J1702 Revised MAY2014 Page 3 of 7 FIGURE 1 - TEST SITE PATTERN 4.5 Test Material 4.5.1 Test Material Pattern The test material defined in 4.5.2 shall be placed in the three placement zones. Th

17、e test material may be arranged to the right or to the left of the guideline to suit the construction and layout of the sweeper. 4.5.2 Test Material Tables 1, 2, and 3 define the type and quantity of test material for tests 1, 2, and 3. The test material media and quantities may be varied according

18、to the type and capacity of sweeper being assessed. The substituted test material quantity and placement shall be stated in the test report. TABLE 1 - TEST 1 - SAND SPREAD QUANTITY Zone Test Material Spread Quantity (Uniform Distribution) X Builders sharp sand 50 kg Y Average grain size 0.5 mm 50 kg

19、 Z Density 1600 kg/m3(dry) 50 kg Total quantity 150 kg SAE INTERNATIONAL J1702 Revised MAY2014 Page 4 of 7 TABLE 2 - TEST 2 - GRAVEL SPREAD QUANTITY Zone Test Material Spread Quantity (Uniform Distribution) X Gravel-granite road stone chips 50 kg Y 12 mm sieve 100% pass 50 kg Z Density 1800 kg/m350

20、kg Total quantity 150 kg TABLE 3 - TEST 3 - OBJECTS Zone Item Object Test Material (Simulant) Quantity Score Rating Per Item Total Score Rating X A Exhaust pipe Steel tube 50 mm u 1.6 mm u 300 mm long 1 6 6 B Stick Wooden dowel - 25 mm u 500 mm long 1 6 6 C Plastic bag Polythene - 300 mm u 300 mm 1

21、6 6 D Carton (flattened) Corrugated cardboard sheet - 300 mm u 300 mm 1 6 6 E Muffler/bottle Steel tube 100 mm u 2.0 mm u 300 mm long 1 6 6 Y F Cobble stone 50 mm spherical flint cobble stone 3 3 9 G Beverage can Aluminum sheet - 80 mm u 150 mm u 2.0 mm 3 3 9 (flattened) thick H Paper sheet A3, 80 g

22、 copy paper 3 3 9 I Rope 10 mm hemp rope u 1000 mm 3 3 9 J Wooden baton 25 mm u 25 mm soft wood u 150 mm long 3 3 9 Z K Bolt M16c hex head steel screw u 75 mm long 5 1 5 L Nut M16c hex head steel nut 5 1 5 M Nail 5.0 steel bar u 75 mm long 5 1 5 N Washer 30 u 2 mm thick steel disk 5 1 5 O Pin 12.0 s

23、teel bar u 40 mm long 5 1 5 Total score 100 or 100% SAE INTERNATIONAL J1702 Revised MAY2014 Page 5 of 7 4.6 Sweeping Tests The sweeper shall make three separate test runs over each of the three prescribed test courses in tests 1, 2, and 3 to collect measured amount of test material in a specific tim

24、e or at a specific speed of operation. Test material for test 1 and test 2 shall be dry. If this is not possible, tests may be made with wet sand, in which case this must be stated with an indication of water inclusion in the test report. Test objects in test 3 that are beyond the capability of the

25、sweeper may be removed from the test course but shall be recorded as not swept material. Any test material or objects being deflected out of or carried beyond the test course shall be reported as not “swept” in the test report. 4.7 Travel Speed During each test run, the sweeper shall be driven at a

26、predetermined speed or timed from start to finish. In order to assess any quantities of residual test material being carried beyond the test course finish line in a speed related test, the sweeping mechanisms shall be disabled at the finish line. For a time-based test, the time taken to disable the

27、sweeping mechanism shall be recorded within the total test time. 5. RESULTS 5.1 Test Analysis All not-swept test material described in 4.5.2 resulting from each test run shall be collected and compared to the total amount initially distributed throughout the three test material placement zones (X, Y

28、, and Z). 5.2 Ratings In test 3, each object is to be rated using the score rating values in Table 3 in the test material schedule. The maximum value is 100 or 100% if all objects are swept and collected. 6. TEST RESULT PRESENTATION In order to present the results of a sweep-ability performance test

29、, a suggested test sheet of the following format could be adopted (Figure 2). SAE INTERNATIONAL J1702 Revised MAY2014 Page 6 of 7 FIGURE 2 - SWEEP-ABILITY PERFORMANCE TEST RESULTS RECORD SAE INTERNATIONAL J1702 Revised MAY2014 Page 7 of 7 7. NOTES 7.1 Marginal Indicia A change bar (l) located in the

30、 left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including technical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only. PREPARED BY THE SAE MTC2, SWEEPER, CLEANER, AND MACHINERY