SAE J 1530-2017 Test Method for Determining Resistance to Fiber Loss Resistance to Abrasion and Bearding of Automotive Carpet Materials.pdf
《SAE J 1530-2017 Test Method for Determining Resistance to Fiber Loss Resistance to Abrasion and Bearding of Automotive Carpet Materials.pdf》由会员分享,可在线阅读,更多相关《SAE J 1530-2017 Test Method for Determining Resistance to Fiber Loss Resistance to Abrasion and Bearding of Automotive Carpet Materials.pdf(5页珍藏版)》请在麦多课文档分享上搜索。
1、_ 6$(7HFKQLFDO6WDQGDUGV%RDUG5XOHVSURYLGHWKDW7KLVUHSRUWLVSX EOLVKHGE6$(WRDGYDQFHWKHVWDWHRIWHFKQLFDODQGHQJL neering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefrom, is the sole reV
2、SRQVLELOLWRIWKHXVHU SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduce
3、d, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-77
4、6-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/J1530_201702 SURFACE VEHICLE RECOMMENDED PRACTICE J1530 FEB2017 Issued 1985-06 Revised 2017-02 Superseding MAY2011 Test Me
5、thod for Determining Resistance to Fiber Loss, Resistance to Abrasion and Bearding of Automotive Carpet Materials RATIONALE 3.1.1 Remove reference to Model No. 5135 &KDQJHGPPWRDSSURLPDWHOPPLQGLDPHWHU DQHDFWVSHFLPHQGLDPHWHURIPPLVQRWUHTXLUHG 5.1.1 Change UHPDLQWRPHDVXUHDGGDUHRXWVLGHRIWKLVUDQJHRUFKDQJH
6、JULWWRJULW WRPDWFKUHTXLUHPHQWVRI$670 GHOHWHIRUFFOHVRU WKLVLVQRWQHFHVVDUZLWKWKHVWDWHPHQWXQWLOWKHFRQIRUPWRWKHVKDSHRIWKHGUXP GHOHWHDQG UHLQVHUWLQWKHVDPHKROGHUDQGLQWKHVDPHSRVLWLRQ RQFHWKHUXEEHUSDGLV UHVXUIDFHGLWVKRXOGQRWEHUHPRYHG DGGUHPRYHRU 1. SCOPE This test method covers determination of abrasion res
7、istance, fiber loss and bearding resistance of automotive carpet materials. 2. REFERENCES There are no referenced publications specified herein. 3. RESISTANCE TO FIBER LOSS BY WEIGHT OF SPECIMEN 3.1 Materials and Equipment Required 3.1.1 Taber Abraser with vacuum accessory or equivalent. 3.1.2 H-18
8、wheels or equivalent. 3.1.3 Weights that yield a total load of 1000 g on each of the abrasive wheels. 3.1.4 S-11 abrasive paper refacing discs or equivalent. 3.1.5 S-37 mounting card, or equivalent. 3.1.6 Calibrated balance. 3.1.7 Clear plastic bags suitable for collecting the fiber. 3.1.8 Crockmete
9、r cloth (80 x 84 thread count, combed cotton, de-sized and bleached). SAE INTERNATIONAL J1530 FEB2017 Page 2 of 5 3.2 Test Specimens 3.2.1 Prepare specimen using a circular die approximately 100 mm in diameter or cut along the circular line on the mounting card. Use a punch to cut a 6 mm diameter ho
10、le in the center of the specimen. 3.2.2 An S-37 mounting card may be used to stabilize the specimen if necessary. 3.2.3 Specimens must be conditioned at 23 C 2 C and 50% 5% relative humidity for a minimum of 24 hours. 3.3 Procedure 3.3.1 Mount H-18 wheels and adjust test instrument for a 1000 g load
11、 per wheel. Reface abrasive wheels before testing each specimen by running them against the S-11 type abrasive paper refacing disc mounted on the turntable for a minimum of 25 cycles. 3.3.2 If the wheels are out-of-round, crowned or excessively clogged with abraded material, the wheels should be dre
12、ssed using a diamond wheel reface machine until the condition is corrected. If there is any doubt about the condition of the wheels, new wheels should be used. 3.3.3 Vacuum or brush the refaced abrasive wheels to remove any loose particles. 3.3.4 Weigh the specimen to the nearest 0.1 g. Record weigh
13、t as W1. 3.3.5 When loss fibers need to be collected, cover the vacuum hose with a piece of crockmeter cloth to collect the abraded fiber and insert the hose into the vacuum port of the Taber abraser. 3.3.6 Place the specimen on the turntable. Place the clamp plate over the turntable screw and tight
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SAEJ15302017TESTMETHODFORDETERMININGRESISTANCETOFIBERLOSSRESISTANCETOABRASIONANDBEARDINGOFAUTOMOTIVECARPETMATERIALSPDF

链接地址:http://www.mydoc123.com/p-1026377.html