SAE AS 9760A-2014 Bolt Machine - Double Hexagon Extended Washer Head Drilled PD Shank Titanium AMS 4967 250-28 UNJF-3A.pdf

《SAE AS 9760A-2014 Bolt Machine - Double Hexagon Extended Washer Head Drilled PD Shank Titanium AMS 4967 250-28 UNJF-3A.pdf》由会员分享，可在线阅读，更多相关《SAE AS 9760A-2014 Bolt Machine - Double Hexagon Extended Washer Head Drilled PD Shank Titanium AMS 4967 250-28 UNJF-3A.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARD BOLT, MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD, DRILLED, PD SHANK, TI 6Al-4V (UNS R56400), .2500-28 UNJF-3A AS9760Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or b

2、y any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.

3、sae.org ISSUED 2000-08REAFFIRMED2005-05REVISED 2014-12THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.AFEDERAL SUPPLY CLASS 5306 AS9760SHEET 1 OF 3REV. APROCUREMENT SPECIFICATION: AS7461SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengi

4、neeringsciences.The useofthis reportisentirelyvoluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffir

5、med, stabilized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS9760ARATIONALE GENERAL REVISION. REVISE LIGHTENING HOLE CONFIGURATION TO ALLOW OPTIONAL SHAPE, ADD ED

6、GE DISTANCE EXCEPTION FOR HEAD MARKING, UPDATE THREADS TO AS8879, UPDATE SURFACE FINISH REQUIREMENTS, ADD AS3062 FOR INCOMPLETE THREAD REQUIREMENTS, ADD POSITION REQUIREMENTS FOR DRILLED HOLES, ADD DATUM REQUIREMENTS FOR -04 THRU -18 LENGTHS (NEW NOTE 1), UPDATE TO ANSI Y14.5M-1982, DELETE .015 MAX

7、RADIUS AT BASE OF WRENCH PAD, DELETE HARDNESS NOTE, AND FIGURE 1 REDRAWN.NOTICE THE INITIAL SAE PUBLICATION OF THIS DOCUMENT WAS TAKEN DIRECTLY FROM U.S. MILITARY STANDARD MS9760, NOTICE 1. THIS SAE STANDARD RETAINS THE SAME PART NUMBERS ESTABLISHED BY THE ORIGINAL MILITARY DOCUMENT. ANY REQUIREMENT

8、S ASSOCIATED WITH QUALIFIED PRODUCTS LISTS (QPL) MAY CONTINUE TO BE MANDATORY FOR DOD CONTRACTS. REQUIREMENTS RELATING TO QPLS HAVE NOT BEEN ADOPTED BY THE SAE FOR THIS STANDARD AND ARE NOT PART OF THIS SAE DOCUMENT. FIGURE 1 - BOLT AEROSPACE STANDARD AS9760SHEET 2 OF 3REV. ABOLT, MACHINE - DOUBLE H

9、EXAGON EXTENDED WASHER HEAD, DRILLED, PD SHANK, TI 6Al-4V (UNS R56400), .2500-28 UNJF-3ATABLE 1 - PART NUMBERS AND DIMENSIONS PARTNUMBER L K APPROX WEIGHT LB/100 PARTNUMBER L K APPROX WEIGHT LB/100 MS9760-04 .365- .385 .079- .099 .71 MS9760-34 2.615-2.635 1.815-1.875 2.15 MS9760-05 .428- .448 .079-

10、.099 .75 MS9760-35 2.740-2.760 1.940-2.000 2.23 MS9760-06 .490- .510 .079- .099 .79 MS9760-36 2.865-2.885 2.065-2.125 2.31 MS9760-07 .552- .572 .079- .099 .83 MS9760-37 2.990-3.010 2.190-2.250 2.39 MS9760-08 .615- .635 .079- .099 .87 MS9760-38 3.115-3.135 2.315-2.375 2.47 MS9760-09 .678- .698 .079-

11、.099 .91 MS9760-39 3.240-3.260 2.440-2.500 2.55 MS9760-10 .740- .760 .079- .099 .95 MS9760-40 3.365-3.385 2.565-2.625 2.64 MS9760-11 .802- .822 .079- .099 .99 MS9760-41 3.490-3.510 2.690-2.750 2.72 MS9760-12 .865- .885 .079- .125 1.03 MS9760-42 3.615-3.635 2.815-2.875 2.80 MS9760-13 .928- .948 .128-

12、 .188 1.07 MS9760-43 3.740-3.760 2.940-3.000 2.88 MS9760-14 .990-1.010 .190- .250 1.11 MS9760-44 3.865-3.885 3.065-3.125 2.96 MS9760-15 1.052-1.072 .252- .312 1.15 MS9760-45 3.990-4.010 3.190-3.250 3.04 MS9760-16 1.115-1.135 .315- .375 1.19 MS9760-46 4.115-4.135 3.315-3.375 3.12 MS9760-17 1.178-1.19

13、8 .378- .438 1.23 MS9760-47 4.240-4.260 3.440-3.500 3.20 MS9760-18 1.240-1.260 .440- .500 1.27 MS9760-48 4.365-4.385 3.565-3.625 3.28 MS9760-19 1.302-1.322 .502- .562 1.31 MS9760-49 4.490-4.510 3.690-3.750 3.36 MS9760-20 1.365-1.385 .565- .625 1.35 MS9760-50 4.615-4.635 3.815-3.875 3.44 MS9760-21 1.

14、428-1.448 .628- .688 1.39 MS9760-51 4.740-4.760 3.940-4.000 3.52 MS9760-22 1.490-1.510 .690- .750 1.43 MS9760-52 4.865-4.885 4.065-4.125 3.60 MS9760-23 1.552-1.572 .752- .812 1.47 MS9760-53 4.990-5.010 4.190-4.250 3.68 MS9760-24 1.615-1.635 .815- .875 1.51 MS9760-54 5.115-5.135 4.315-4.375 3.76 MS97

15、60-25 1.678-1.698 .878- .938 1.55 MS9760-55 5.240-5.260 4.440-4.500 3.84 MS9760-26 1.740-1.760 .940-1.000 1.59 MS9760-56 5.365-5.385 4.565-4.625 3.92 MS9760-27 1.802-1.822 1.002-1.062 1.63 MS9760-57 5.490-5.510 4.690-4.750 4.00 MS9760-28 1.865-1.885 1.065-1.125 1.67 MS9760-58 5.615-5.635 4.815-4.875

16、 4.08 MS9760-29 1.990-2.010 1.190-1.250 1.75 MS9760-59 5.740-5.760 4.940-5.000 4.16 MS9760-30 2.115-2.135 1.315-1.375 1.83 MS9760-60 5.865-5.885 5.065-5.125 4.24 MS9760-31 2.240-2.260 1.440-1.500 1.91 MS9760-61 5.990-6.010 5.190-5.250 4.32 MS9760-32 2.365-2.385 1.565-1.625 1.99 MS9760-33 2.490-2.510

17、 1.690-1.750 2.07 NOTES: /1/ FOR PART NUMBERS MS9760-04 THRU MS9760-18 DATUM Z SHALL REPLACE DATUM Y.2. PROCUREMENT SPECIFICATION: AS7461. 3. MATERIAL: AMS4967 (TITANIUM ALLOY 6Al - 4V, COMPOSITION SIMILAR TO UNS R56400). 4. FLUORESCENT PENETRANT INSPECTION PER ASTM E1417/E1417M, TYPE 1, SENSITIVITY

18、 LEVEL 2 MIN. 5. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra EXCEPT UPSET HEAD. 6. BREAK SHARP EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 7. DIMENSIONS IN INCHES. 8. DIMENSIONING AND TOLERANCING PER ANSI Y1

19、4.5M-1982 (ASME PUBLICATION). 9. DO NOT USE UNASSIGNED PART NUMBERS. AEROSPACE STANDARD AS9760SHEET 3 OF 3REV. ABOLT, MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD, DRILLED, PD SHANK, TI 6Al-4V (UNS R56400), .2500-28 UNJF-3A10. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF TH

20、E USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN ASTM INTERNATIONAL PUBLICATION.