SAE AS 9679B-2014 BOLT MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD PD SHANK CUP WASHER LOCKED CRES UNS S66286 130 KSI MIN 3750-24 UNJF-3A《最小值为130 KSI的UNS S66286耐蚀钢杯形垫圈锁定PD杆双六角头扩展.pdf

《SAE AS 9679B-2014 BOLT MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD PD SHANK CUP WASHER LOCKED CRES UNS S66286 130 KSI MIN 3750-24 UNJF-3A《最小值为130 KSI的UNS S66286耐蚀钢杯形垫圈锁定PD杆双六角头扩展.pdf》由会员分享，可在线阅读，更多相关《SAE AS 9679B-2014 BOLT MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD PD SHANK CUP WASHER LOCKED CRES UNS S66286 130 KSI MIN 3750-24 UNJF-3A《最小值为130 KSI的UNS S66286耐蚀钢杯形垫圈锁定PD杆双六角头扩展.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARD BOLT, MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD, PD SHANK, CUP WASHER LOCKED,CRES, UNS S66286, 130 KSI MIN, .3750-24 UNJF-3AAS9679Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, i

2、n any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDR

3、ESS: http:/www.sae.org ISSUED 1999-04REAFFIRMED2007-06REVISED 2014-08THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.BFEDERAL SUPPLY CLASS 5306 AS9679SHEET 1 OF 3REV. BPROCUREMENT SPECIFICATION: AS7477SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of t

4、echnicalandengineeringsciences.The useofthis reportisentirelyvoluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay be

5、revised,reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS9679BRATIONALE REVISE WRENCHING ELEMENT RUNOUT CALLOUT (RELOCATE FROM WRENCH FLATS TO

6、POINTS), REVISE LIGHTENING HOLE CONFIGURATION (REVISE SECTION VIEW) TO ALLOW OPTIONAL SHAPE AT BOTTOM OF HOLE. DELETE RADIUS AT TRANSITION OF WRENCH FLATS AND BASE FLANGE, UPDATE REFERENCES. NOTICE THE INITIAL SAE PUBLICATION OF THIS DOCUMENT WAS TAKEN DIRECTLY FROM U.S. MILITARY STANDARD MS9679B, A

7、MENDMENT 1. THIS SAE STANDARD MAY RETAIN THE SAME PART NUMBERS ESTABLISHED BY THE ORIGINAL MILITARY DOCUMENT. ANY REQUIREMENTS ASSOCIATED WITH QUALIFIED PRODUCTS LISTS (QPL) MAY CONTINUE TO BE MANDATORY FOR DOD CONTRACTS. REQUIREMENTS RELATING TO QPLS HAVE NOT BEEN ADOPTED BY THE SAE FOR THIS STANDA

8、RD AND ARE NOT PART OF THIS SAE DOCUMENT. FIGURE 1 - BOLT AEROSPACE STANDARD AS9679SHEET 2 OF 3REV. BBOLT, MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD, PD SHANK, CUP WASHER LOCKED, CRES, UNS S66286, 130 KSI MIN, .3750-24 UNJF-3A TABLE 1 - PART NUMBERS AND DIMENSIONS PARTNUMBER L K APPROX. MASSLB/1

9、00 PARTNUMBER L K APPROX. MASSLB/100 MS9679-02 .490- .510 .088- .108 2.79 MS9679-30 2.740-2.760 1.690-1.750 8.87 MS9679-03 .552- .572 .088- .108 2.95 MS9679-31 2.865-2.885 1.815-1.875 9.22 MS9679-04 .615- .635 .088- .108 3.11 MS9679-32 2.990-3.010 1.940-2.000 9.56 MS9679-05 .678- .698 .088- .108 3.2

10、7 MS9679-33 3.115-3.135 2.065-2.125 9.89 MS9679-06 .740- .760 .088- .108 3.44 MS9679-34 3.240-3.260 2.190-2.250 10.24 MS9679-07 .802- .822 .088- .108 3.60 MS9679-35 3.365-3.385 2.315-2.375 10.57 MS9679-08 .865- .885 .088- .108 3.77 MS9679-36 3.490-3.510 2.440-2.500 10.91 MS9679-09 .928- .948 .088- .

11、108 3.94 MS9679-37 3.615-3.635 2.565-2.625 11.23 MS9679-10 .990-1.010 .088- .108 4.11 MS9679-38 3.740-3.760 2.690-2.750 11.58 MS9679-11 1.052-1.072 .088- .108 4.28 MS9679-39 3.865-3.885 2.815-2.875 11.90 MS9679-12 1.115-1.135 .088- .125 4.46 MS9679-40 3.990-4.010 2.940-3.000 12.23 MS9679-13 1.178-1.

12、198 .128- .188 4.62 MS9679-41 4.115-4.135 3.065-3.125 12.56 MS9679-14 1.240-1.260 .190- .250 4.79 MS9679-42 4.240-4.260 3.190-3.250 12.89 MS9679-15 1.302-1.322 .252- .312 4.96 MS9679-43 4.365-4.385 3.315-3.375 13.22 MS9679-16 1.365-1.385 .315- .375 5.14 MS9679-44 4.490-4.510 3.440-3.500 13.65 MS9679

13、-17 1.428-1.448 .378- .438 5.32 MS9679-45 4.615-4.635 3.565-3.625 13.99 MS9679-18 1.490-1.510 .440- .500 5.48 MS9679-46 4.740-4.760 3.690-3.750 14.32 MS9679-19 1.552-1.572 .502- .562 5.65 MS9679-47 4.865-4.885 3.815-3.875 14.65 MS9679-20 1.615-1.635 .565- .625 5.82 MS9679-48 4.990-5.010 3.940-4.000

14、14.99 MS9679-21 1.678-1.698 .628- .688 5.99 MS9679-49 5.115-5.135 4.065-4.125 15.33 MS9679-22 1.740-1.760 .690- .750 6.16 MS9679-50 5.240-5.260 4.190-4.250 15.66 MS9679-23 1.865-1.885 .815- .875 6.50 MS9679-51 5.365-5.385 4.315-4.375 15.99 MS9679-24 1.990-2.010 .940-1.000 6.84 MS9679-52 5.490-5.510

15、4.440-4.500 16.32 MS9679-25 2.115-2.135 1.065-1.125 7.18 MS9679-53 5.615-5.635 4.565-4.625 16.65 MS9679-26 2.240-2.260 1.190-1.250 7.52 MS9679-54 5.740-5.760 4.690-4.750 16.99 MS9679-27 2.365-2.385 1.315-1.375 7.85 MS9679-55 5.865-5.885 4.815-4.875 17.33 MS9679-28 2.490-2.510 1.440-1.500 8.19 MS9679

16、-56 5.990-6.010 4.940-5.000 17.67 MS9679-29 2.615-2.635 1.565-1.625 8.53 AEROSPACE STANDARD AS9679SHEET 3 OF 3REV. BBOLT, MACHINE - DOUBLE HEXAGON EXTENDED WASHER HEAD, PD SHANK, CUP WASHER LOCKED, CRES, UNS S66286, 130 KSI MIN, .3750-24 UNJF-3A NOTES: /1/ FOR PART NUMBERS MS9679-02 THRU MS9679-19 D

17、ATUM Z SHALL REPLACE DATUM Y.2. MATERIAL: CORROSION AND HEAT RESISTANT STEEL PER AMS5731 (UNS S66286). 3. PROCUREMENT SPECIFICATION: AS7477 4. FLUORESCENT PENETRANT INSPECTION PER ASTM E1417/E1417M, TYPE 1, SENSITIVITY LEVEL 2 MIN. 5. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME

18、B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra. 6. BREAK SHARP EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED. 7. DIMENSIONS ARE IN INCHES. 8. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M-1982 (ASME PUBLICATION). 9. DO NOT USE UNASSIGNED PART NUMBERS. 10. A CHANGE BAR (l) LOCAT

19、ED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN ASTM INTERNATIONAL PUBLICATION.