SAE AS 9245B-2014 PIN COTTER - CRES UNS S32100 AS7211《针型开口销 耐蚀钢(CRES) UNS S32100 AS7211》.pdf

《SAE AS 9245B-2014 PIN COTTER - CRES UNS S32100 AS7211《针型开口销 耐蚀钢(CRES) UNS S32100 AS7211》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 9245B-2014 PIN COTTER - CRES UNS S32100 AS7211《针型开口销 耐蚀钢(CRES) UNS S32100 AS7211》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARD PIN, COTTER - CRES, UNS S32100, AS7211 AS9245Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise

2、, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1998-08REAFFIRMED 2013-10 REVISED 2014-02THIRD ANGLE PROJEC

3、TION CUSTODIAN: E-25 REV.BFEDERAL SUPPLY CLASS 5315 AS9245SHEET 1 OF 2REV. BPROCUREMENT SPECIFICATION: AS7211SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirely voluntary, andits app

4、licability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments ands

5、uggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS9245BRATIONALE THIS IS A LIMITED SCOPE REVISION. THE FEDERAL SUPPLY CLASS HAS BEEN CORRECTED AND RESTORED TO AGREE WITH THE ORIGINAL PUBLICATION. NOTICE THE INITIAL SA

6、E PUBLICATION OF THIS DOCUMENT WAS TAKEN DIRECTLY FROM U.S. MILITARY STANDARD MS9245A(ASG). THIS SAE STANDARD MAY RETAIN THE SAME PART NUMBERS ESTABLISHED BY THE ORIGINAL MILITARY DOCUMENT. ANY REQUIREMENTS ASSOCIATED WITH QUALIFIED PRODUCTS LISTS (QPL) MAY CONTINUE TO BE MANDATORY FOR DOD CONTRACTS

7、. REQUIREMENTS RELATING TO QPLS HAVE NOT BEEN ADOPTED BY THE SAE FOR THIS STANDARD AND ARE NOT PART OF THIS SAE DOCUMENT. FIGURE 1 - PIN AEROSPACE STANDARD AS9245SHEET 2 OF 2REV. BPIN, COTTER - CRES, UNS S32100, AS7211 TABLE 1 - PART NUMBERS AND DIMENSIONS NOM DIA .0312 .0625 .0938 .125 .156 .188 A

8、DIA .027 - .030 .058 - .061 .086 - .090 .118 - .122 .146 - .150 .172 - .176 B DIA +.030 -.000 .031 .062 .094 .125 .156 .188 LENGTH (L) .030 PART NUMBER .250 .312 .375 .438 .500 .562 .625 .750 .875 1.000 1.125 1.250 1.375 1.500 1.625 1.750 2.000 MS9245-01 MS9245-02 MS9245-03 MS9245-04 MS9245-05 MS924

9、5-06 MS9245-07 MS9245-08 MS9245-09 MS9245-10 MS9245-21 MS9245-22 MS9245-23 MS9245-24 MS9245-25 MS9245-26 MS9245-27 MS9245-28 MS9245-29 MS9245-30 MS9245-31 MS9245-32 MS9245-33 MS9245-34 MS9245-35 MS9245-36 MS9245-37 MS9245-40 MS9245-41 MS9245-42 MS9245-43 MS9245-44 MS9245-45 MS9245-46 MS9245-47 MS924

10、5-48 MS9245-49 MS9245-50 MS9245-51 MS9245-52 MS9245-53 MS9245-54 MS9245-58 MS9245-59 MS9245-60 MS9245-61 MS9245-62 MS9245-63 MS9245-64 MS9245-65 MS9245-66 MS9245-67 MS9245-68 MS9245-69 MS9245-70 MS9245-71 MS9245-75 MS9245-76 MS9245-77 MS9245-78 MS9245-79 MS9245-80 MS9245-81 MS9245-82 MS9245-83 MS924

11、5-84 MS9245-85 MS9245-86 MS9245-87 MS9245-88 MS9245-94 MS9245-95 MS9245-96 MS9245-97 MS9245-98 MS9245-99 Y .002 .016 .045 .107 .198 .324 Z .018 .079 .174 .323 .492 .680 NOTES: 1. MATERIAL AND PROCUREMENT SPECIIFCATION: AS7211 (UNS S32100). 2. HEAT TREATMENT: HEAT AT 1200 F TO PRODUCE DARK GRAY OR BL

12、ACK COLOR. OTHER SPECIFICATION REQUIREMENTS SHALL BE MAINTAINED AFTER HEAT TREATMENT. 3. ENDS OF THE PINS SHALL NOT BE OPEN AND ANY GAPS BETWEEN THE PRONGS ALONG THE SHANK PORTION OF THE PINS BEYOND THE POINT SHALL NOT EXCEED .015. MISALIGNMENT OF PRONGS OVER ENTIRE LENGTH OF SHANK SHALL NOT EXCEED

13、.015. 4. COTTER PINS SHALL BE FREE FROM BURRS. 5. DIMENSIONS ARE IN INCHES. 6. ALL STYLES ARE ACCEPTABLE. STYLE SHALL NOT BE INCORPORATED IN THE PART NUMBER. 7. DO NOT USE UNASSIGNED PART NUMBERS. 8. APPROXIMATE WEIGHT: THE WEIGHT PER 100 COTTER PINS = Y + (L X Z). 9. A CHANGE BAR (l) LOCATED IN THE

14、 LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS IS A SAE INTERNATIONAL PUBLICATION.