SAE AS 9204B-2004 Gasket - Metal O-Ring 094 Tube x 010 Wall Cres - UNS S31200《 094管 X 010壁厚、CRES UNS S32100金属O型密封圈》.pdf

《SAE AS 9204B-2004 Gasket - Metal O-Ring 094 Tube x 010 Wall Cres - UNS S31200《 094管 X 010壁厚、CRES UNS S32100金属O型密封圈》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 9204B-2004 Gasket - Metal O-Ring 094 Tube x 010 Wall Cres - UNS S31200《 094管 X 010壁厚、CRES UNS S32100金属O型密封圈》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD GASKET - METAL O-RING, .094 TUBE X .010 WALL, CRES - UNS S32100 AS9204 Copyright 2004 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopyi

2、ng, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: custsvcsae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1998-11REVISED 2004-07 THIRD ANGLE PROJECTI

3、ON CUSTODIAN: SAE E-25 REV. B FEDERAL SUPPLY CLASS5330 AS9204 SHEET 1 OF 4 REV.B THE INITIAL SAE PUBLICATION OF THIS DOCUMENT WAS TAKEN DIRECTLY FROM U.S. MILITARY STANDARD MS9204A(ASG), AMENDMENT 1. THIS SAE STANDARD RETAINS THE SAME PART NUMBERS ESTABLISHED BY THE ORIGINAL MILITARY DOCUMENT. ANY R

4、EQUIREMENTS ASSOCIATED WITH QUALIFIED PRODUCTS LISTS (QPL) MAY CONTINUE TO BE MANDATORY FOR DOD CONTRACTS. REQUIREMENTS RELATING TO QPLS HAVE NOT BEEN ADOPTED BY THE SAE FOR THIS STANDARD AND ARE NOT PART OF THIS SAE DOCUMENT. AEROSPACE STANDARD GASKET - METAL O-RING, .094 TUBE X .010 WALL, CRES - U

5、NS S32100 AS9204 REV. B AS9204 SHEET 2 OF 4 REV.B FIGURE 1 TABLE 1 - PART NUMBERS AND DIMENSIONS AEROSPACE STANDARD GASKET - METAL O-RING, .094 TUBE X .010 WALL, CRES - UNS S32100 AS9204 REV. B AS9204 SHEET 3 OF 4 REV.B TABLE 1 - PART NUMBERS AND DIMENSIONS (CONTINUED) AEROSPACE STANDARD GASKET - ME

6、TAL O-RING, .094 TUBE X .010 WALL, CRES - UNS S32100 AS9204 REV. B AS9204 SHEET 4 OF 4 REV.B NOTES: 1. *PREFERRED SIZES. 2. MATERIAL: STEEL, CORROSION AND HEAT RESISTANT, TUBING AMS 5570 (UNS S32100) OR AMS 5576 (UNS S32100). TUBE SIZE .093-.097 DIA, WALL THICKNESS .009-.011. 3. PROCUREMENT SPECIFIC

7、ATION: AS7325. 4. RING SHALL BE FLAT WITHIN B. 5. FINISH WELD FLUSH WITH TUBE OD. SMOOTH BLEND WITHIN .125 OF WELD. DIMENSIONS AT BLEND SHALL NOT BE MORE THAN .004 BELOW ADJACENT SURFACES. 6. IDENTIFICATION: MARK PART NUMBER AND MANUFACTURERS IDENTIFICATION ON CONTAINER. 7. SURFACE TEXTURE: SYMBOLS

8、PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. 8. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M-1982 (ASME PUBLICATION). 9. DIMENSIONS IN INCHES. 10. DO NOT USE UNASSIGNED PART NUMBERS. 11. THE CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE REVI

9、SIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT. 12. SEE ARP674 FOR RECOMMENDED GROOVE DESIGN. AS AND AMS ARE SOCIETY OF AUTOMOTIVE ENGINEERS, INC. PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION.