SAE AS 85560 1B-2013 BEARING FIBER REINFORCED PLASTIC SLEEVE PLAIN SELF LUBRICATING +250 《+250℉纤维增强塑料套管自润滑式滑动轴承》.pdf

《SAE AS 85560 1B-2013 BEARING FIBER REINFORCED PLASTIC SLEEVE PLAIN SELF LUBRICATING +250 《+250℉纤维增强塑料套管自润滑式滑动轴承》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 85560 1B-2013 BEARING FIBER REINFORCED PLASTIC SLEEVE PLAIN SELF LUBRICATING +250 《+250℉纤维增强塑料套管自润滑式滑动轴承》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARD BEARING, FIBER REINFORCED PLASTIC, SLEEVE, PLAIN, SELF LUBRICATING, +250 F AS85560/1Copyright 2013 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical

2、, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2004-11REVISED 2013-

3、01THIRD ANGLE PROJECTION CUSTODIAN: AIRFRAME CONTROL BEARING GROUP REV.BFEDERAL SUPPLY CLASS 3120 REV. BPROCUREMENT SPECIFICATION: NONESAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is enti

4、rely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirmed, revised, orcancelled. SAE invites yourwritte

5、ncomments andsuggestions. AS85560/1SHEET 1 OF 3RATIONALE AS85560/1B WAS CREATED IN ASSOCIATION WITH THE FIVE YEAR DOCUMENT REVIEW TO UPDATE NUMBER FORMATTING IN ACCORDANCE WITH THE SAE TECHNICAL REPORT STYLE MANUAL. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CO

6、NSIST OF THIS DOCUMENTAND THE LATEST ISSUE OF: SAE AS85560. FIGURE 1 TABLE 1 - DIMENSIONS PART NO.-XX NOMINAL BORE SIZE B DIA. +.0000 .0010 D DIA. +.0005 .0005 M85560/1-04 M85560/1-05 M85560/1-06 M85560/1-07 M85560/1-08 M85560/1-09 M85560/1-10 M85560/1-11 M85560/1-12 M85560/1-14 M85560/1-16 M85560/1

7、-18 M85560/1-20 M85560/1-22 M85560/1-24 M85560/1-26 M85560/1-28 M85560/1-32 1/4 5/16 3/8 7/16 1/2 9/16 5/8 11/16 3/4 7/8 11-1/8 1-1/4 1-3/8 1-1/2 1-5/8 1-3/4 2.2515 .3140 .3765 .4390 .5015 .5640 .6265 .6890 .7515 .8765 1.0015 1.1265 1.2515 1.3765 1.5015 1.6265 1.7515 2.0015 .3760 .4386 .5012 .5638 .

8、6265 .6892 .8142 .8767 .9393 1.0645 1.1898 1.3148 1.4398 1.5648 1.7523 1.8773 2.0023 2.2523 SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS85560/1BAEROSPACE STANDARD AS85560/1SHEET 2 OF 3REV. BBEARING, FIBER REINFORCED PLASTIC

9、, SLEEVE, PLAIN, SELF-LUBRICATING, +250 F MATERIAL: COMPOSITE: GLASS OR ARAMID FIBERS IN RESIN MATRIX. SELF-LUBRICATING SURFACE: TETRAFLUOROETHYLENE PER AS85560. SURFACE TEXTURE: UNLESS OTHERWISE SPECIFIED, SMOOTH MACHINE FINISH 125 MICROINCH Ra MAXIMUM ON OD, 250 MICROINCH Ra MAXIMUM ON ALL OTHER S

10、URFACES IN ACCORDANCE WITH ASME B46.1. SURFACE TEXTURE OF SELF-LUBRICATING SURFACE IS NOT SPECIFIED. TEMPERATURE RANGE: 65 TO +250 F. BREAK SHARP EDGES AND CORNERS AND REMOVE ALL BURRS AND SLIVERS. UNLESS OTHERWISE SPECIFIED, DIMENSIONS IN INCHES. MARKING: FOR DASH NO. 08 AND LARGER, THE PART NUMBER

11、 FROM TABLE 1 SHALL BE MARKED ON THE PART. SMALLER SIZES SHOULD BE IDENTIFIED USING A TAG OR ON THE BAG. NOTES: 1. EXAMPLE OF PART NUMBER: M85560/1 -04 -008 = .250 IN BORE DIAMETER BY .250 IN LONG LENGTH CODE IN ACCORDANCE WITH TABLE 2 (USE ONLY ASSIGNED LENGTH CODES SHOWN IN TABLE 2) BORE DIAMETER

12、CODE IN ACCORDANCE WITH TABLE 1 (USE ONLY ASSIGNED BORE CODES SHOWN IN TABLE 1) BASIC PART NUMBER 2. IN THE EVENT OF A CONFLICT BETWEEN THE TEXT OF THIS STANDARD AND THE REFERENCED CITED HEREIN, THE TEXT OF THIS STANDARD SHALL TAKE PRECEDENCE. 3. REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT

13、ON THE DATE OF INVITATION FOR BID AND FORM A PART OF THIS STANDARD TO THE EXTENT SPECIFIED HEREIN. 4. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUME

14、NT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. LOAD RATINGS: RADIAL STATIC LIMIT LOAD = 50 000 x B x (L

15、0.1) POUND DYNAMIC RADIAL LOAD = 25 000 x B x (L 0.1) POUND AEROSPACE STANDARD AS85560/1SHEET 3 OF 3REV. BBEARING, FIBER REINFORCED PLASTIC, SLEEVE, PLAIN, SELF-LUBRICATING, +250 F TABLE 2 - LENGTH CODES PART NO. NOMINAL SIZELENGTH L + .000/ -.010 1/4 9/32 5/16 11/32 3/8 7/16 1/2 9/16 5/8 11/16 3/4

16、7/8 M85560/1-04 1/4 008 009 010 011 012 014 M85560/1-05 5/16 008 009 010 011 012 014 016 018 M85560/1-06 3/8 008 009 010 011 012 014 016 018 020 022 M85560/1-07 7/16 008 009 010 011 012 014 016 018 020 022 024 028 M85560/1-08 1/2 008 009 010 011 012 014 016 018 020 022 024 028 M85560/1-09 9/16 008 0

17、09 010 011 012 014 016 018 020 022 024 028 M85560/1-10 5/8 008 009 010 011 012 014 016 018 020 022 024 028 M85560/1-11 11/16 008 009 010 011 012 014 016 018 020 022 024 028 M85560/1-12 3/4 008 009 010 011 012 014 016 018 020 022 024 028 M85560/1-14 7/8 008 009 010 011 012 014 016 018 020 022 024 028

18、 M85560/1-16 1 008 009 010 011 012 014 016 018 020 022 024 028 M85560/1-18 1 1/8 010 011 012 014 016 018 020 022 024 028 M85560/1-20 1 1/4 012 014 016 018 020 022 024 028 M85560/1-22 1 3/8 012 014 016 018 020 022 024 028 M85560/1-24 1 1/2 012 014 016 018 020 022 024 028 M85560/1-26 1 5/8 016 018 020

19、 022 024 028 M85560/1-28 1 3/4 016 018 020 022 024 028 M85560/1-32 2 016 018 020 022 024 028 PART NO. NOMINAL SIZELENGTH L + .000/-.010 1 1 1/8 1 1/4 1 3/8 1 1/2 1 5/8 1 3/4 1 7/8 2 2 1/8 2 1/4 2 3/8 2 1/2 2 3/4 3 M85560/1-04 1/4 M85560/1-05 5/16 M85560/1-06 3/8 M85560/1-07 7/16 M85560/1-08 1/2 M855

20、60/1-09 9/16 032 036 M85560/1-10 5/8 032 036 040 044 M85560/1-11 11/16 032 036 040 044 048 052 M85560/1-12 3/4 032 036 040 044 048 052 M85560/1-14 7/8 032 036 040 044 048 052 M85560/1-16 1 032 036 040 044 048 052 056 060 M85560/1-18 1 1/8 032 036 040 044 048 052 056 060 M85560/1-20 1 1/4 032 036 040

21、 044 048 052 056 060 064 068 M85560/1-22 1 3/8 032 036 040 044 048 052 056 060 064 068 M85560/1-24 1 1/2 032 036 040 044 048 052 056 060 064 068 072 076 080 088 M85560/1-26 1 5/8 032 036 040 044 048 052 056 060 064 068 072 076 080 088 096 M85560/1-28 1 3/4 032 036 040 044 048 052 056 060 064 068 072 076 080 088 096 M85560/1-32 2 032 036 040 044 048 052 056 060 064 068 072 076 080 088 096