SAE AS 85049 94C-2011 CONNECTOR ACCESSORIES ELECTRICAL MOUNTING DEVICE FLANGE TYPE CATEGORY 7 FULL PERIMETER《全周长类7法兰型安装设备电连接器配件》.pdf

《SAE AS 85049 94C-2011 CONNECTOR ACCESSORIES ELECTRICAL MOUNTING DEVICE FLANGE TYPE CATEGORY 7 FULL PERIMETER《全周长类7法兰型安装设备电连接器配件》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 85049 94C-2011 CONNECTOR ACCESSORIES ELECTRICAL MOUNTING DEVICE FLANGE TYPE CATEGORY 7 FULL PERIMETER《全周长类7法兰型安装设备电连接器配件》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD CONNECTOR ACCESSORIES, ELECTRICAL, MOUNTING DEVICE, FLANGE TYPE, CATEGORY 7, FULL PERIMETER AS85049/94Copyright 2016 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, ele

2、ctronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED20

3、01-07 REVISED2011-05 REAFFIRMED2016-08 THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C1 REV.C FEDERAL SUPPLY CLASS 5935 AS85049/94 SHEET 1 OF 4 REV. C PROCUREMENT SPECIFICATION: AS85049 SAE Technical StandardsBoardRulesprovidethat:“ThisreportispublishedbySAE toadvancethestateoftechnicalandengineering s

4、ciences. The use of thisreport isentirelyvoluntary, andits applicability andsuitability for any particularuse, includingany patentinfringement arising therefrom,is the soleresponsibility of theuser.”SAE reviewseachtechnical reportatleasteveryfiveyearsatwhichtimeitmayberevised,reaffirmed,stabilized,o

5、rcancelled. SAEinvites yourwritten comments andsuggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AS85049/94C RATIONALE AS85049/94C HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. NOTICE THE REQUIREM

6、ENTS FOR ACQUIRING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION SHEET AND THE LATEST ISSUE OF SAE AS85049. FIGURE 1 MOUNTING DEVICE CONFIGURATION AEROSPACE STANDARD AS85049/94 SHEET 2 OF 4 CONNECTOR ACCESSORIES, ELECTRICAL, MOUNTING DEVICE, FLANGE TYPE, CATEGORY 7, FULL PERIMETER

7、 REV. C TABLE 1 - DIMENSIONS DASH NUMBER THRD UNJC-3B A .015 B MAX C D 8 4-40 .594 (15.09) .900 (22.86) .555 (14.10) .585 (14.86) .106 (2.69) .166 (4.22) 10 4-40 .719 (18.26) 1.034 (26.26) .685 (17.40) .735 (18.67) .106 (2.69) .166 (4.22) 12 4-40 .812 (20.62) 1.119 (28.42) .820 (20.83) .860 (21.84)

8、.106 (2.69) .166 (4.22) 14 4-40 .906 (23.01) 1.213 (30.81) .945 (24.00) .990 (25.15) .106 (2.69) .166 (4.22) 16 4-40 .969 (24.61) 1.295 (32.89) 1.070 (27.18) 1.100 (27.94) .106 (2.69) .166 (4.22) 18 4-40 1.062 (26.97) 1.421 (36.09) 1.195 (30.35) 1.225 (30.99) .106 (2.69) .166 (4.22) 20 4-40 1.156 (2

9、9.36) 1.550 (39.37) 1.320 (33.53) 1.350 (34.29) .106 (2.69) .166 (4.22) 22 4-40 1.250 (31.75) 1.680 (42.67) 1.440 (36.58) 1.485 (37.72) .106 (2.69) .166 (4.22) 24 6-32 1.375 (34.93) 1.800 (45.72) 1.570 (39.88) 1.600 (40.64) .123 (3.12) .183 (4.65) 25 6-32 1.500 (38.10) 1.910 (48.51) 1.643 (41.73) 1.

10、673 (42.49) .123 (3.12) .183 (4.65) NOTES: 1. DIMENSIONS ARE INCHES. 2. UNLESS OTHERWISE SPECIFIED, TOLERANCE IS .010. 3. FOR MOUNTING FLANGE APPLICATION INFORMATION, SEE TABLE 2. REQUIREMENTS: DESIGN AND CONSTRUCTION: 1. DIMENSIONS AND CONFIGURATION SHALL BE IN ACCORDANCE WITH FIGURE 1, TABLE 1. 2.

11、 FIGURE 1, MOUNTING FLANGES SHALL BE OF A CONSTRUCTION WITH PREDRILLED OR PUNCHED HOLES IN ALUMINUM ALLOY INCORPORATING SELF LOCKING NUTS, CLINCH TYPE. 3. MATERIAL AND FINISH: FLANGES, ALUMINUM ALLOY IN ACCORDANCE WITH SAE AS85049, CHEMICAL CONVERSION COATING PER MIL-DTL-5541, CLASS 1A. WHEN SPECIFI

12、ED IN THE PART NUMBER, BY LETTER A DESIGNATOR, 2 COATS OF EPOXY POLYAMIDE PRIMER PER MIL-PRF-23377, TYPE I, SHALL BE APPLIED EITHER BEFORE OR AFTER NUT INSTALLATION AND OVERSPRAY IS ALLOWED PROVIDED THE PERFORMANCE CHARACTERISTICS OF THE NUT ARE NOT DEGRADED AND ALL OTHER REQUIREMENTS ARE MET. 4. CL

13、INCH NUTS: IN ACCORDANCE WITH NASM45938, CLEAN AND DE-SCALE IN ACCORDANCE WITH ASTM A 380 AND/OR PASSIVATE IN ACCORDANCE WITH AMS-QQ-P-35, FOLLOWED BY A SOLID FILM LUBRICANT COATING PER MIL-PRF-46010. AEROSPACE STANDARD AS85049/94 SHEET 3 OF 4 CONNECTOR ACCESSORIES, ELECTRICAL, MOUNTING DEVICE, FLAN

14、GE TYPE, CATEGORY 7, FULL PERIMETER REV. C 5. PART NUMBER: SEE EXAMPLE BELOW: EXAMPLE: M85049/ 94 - 14 - A BASIC PART NUMBER SPECIFICATION SHEET DASH NUMBER (SEE TABLE 1) PART COAT REQUIRED (SEE REQUIREMENT 3) 6. QUALIFICATION: SEE SAE AS85049, CATEGORY 7, WITH THE FOLLOWING ADDITIONS: A. INSTALLATI

15、ON: WHEN TESTED AS SPECIFIED HEREIN EVIDENCE OF COCKING, LOOSENESS, SPLITS OR CRACKS SHALL BE CAUSE FOR REJECTION. B. SALT SPRAY: IN ACCORDANCE WITH SAE AS85049, STANDARD TEST, 96 HOUR DURATION FOR CHEMICAL CONVERSION COATED PARTS AND EXTENDED TEST, 500 HOUR DURATION FOR POLYAMIDE PRIMER COATED PART

16、S. C. VIBRATION: IN ACCORDANCE WITH SAE AS85049, RANDOM VIBRATION-MEDIUM DUTY, UNWIRED MOUNTED WITH FLANGE RECEPTACLE CONNECTOR ONLY. D. SHOCK: IN ACCORDANCE WITH SAE AS85049, SHOCK-MEDIUM AND LIGHT DUTY, UNWIRED MOUNTED WITH FLANGE RECEPTACLE CONNECTOR ONLY. 7. PERIODIC QUALIFICATION: SEE AS85049,

17、CATEGORY 7, WITH THE FOLLOWING ADDITIONS: A. LOCKING TORQUE: IN ACCORDANCE WITH NASM25027. B. TORQUE OUT: IN ACCORDANCE WITH NASM45938, EXCEPT THE REQUIREMENT SHALL BE 15 IN LB MINIMUM FOR 4-40 THREADED NUTS AND 20 IN LB MINIMUM FOR 6-32 THREADED NUTS. C. PUSH OUT: IN ACCORDANCE WITH NASM45938, EXCE

18、PT THE REQUIREMENT SHALL BE 88 LB MINIMUM FOR 4-40 THREADED NUTS AND 105 LB MINIMUM FOR 6-32 THREADED NUTS. D. POST EXAMINATION. TABLE 2 - MOUNTING FLANGE CONNECTOR APPLICATION DATA 1/ AS85049/94 DASH NO MIL-DTL-38999 AS50151 AS81703 SERIES 3 SERIES I SERIES II SERIES III SERIES IV CONNECTOR SHELL S

19、IZE 8 8 8S 10 9 10 9 (A) 10SL 7 12 11 12 11 (B) 11 (B) 12, 12S 12 14 13 14 13 (C) 13 (C) 14, 14S 19 16 15 16 15 (D) 15 (D) 16, 16S 27 18 17 18 17 (E) 17 (E) 18 20 19 20 19 (F) 19 (F) 20 22 21 22 21 (G) 21 (G) 22 24 23 24 23 (H) 23 (H) 24 25 25 25 (J) 25 (J) AEROSPACE STANDARD AS85049/94 SHEET 4 OF 4

20、 CONNECTOR ACCESSORIES, ELECTRICAL, MOUNTING DEVICE, FLANGE TYPE, CATEGORY 7, FULL PERIMETER REV. C TABLE 2 - MOUNTING FLANGE CONNECTOR APPLICATION DATA 1/ (CONTINUED) AS85049/94 DASH NO MIL-DTL-26482 SERIES 1 & 2 MIL-DTL-83723 SERIES III MIL-DTL-26500 NAS 1599 MIL-C-81511 MIL-DTL-27599CONNECTOR SHE

21、LL SIZE 8 8 8 8 8 8 10 10 10 10 10 10 12 12 12 12 12 14 14 14 14 14 14 16 16 16 16 16 16 18 18 18 18 18 18 20 20 20 20 20 20 22 22 22 22 22 22 24 24 24 24 24 24 25 1/ THE INFORMATION ABOVE IS SHOWN FOR REFERENCE ONLY. IT IS RECOMMEDED THE USER VERIFY THE CONNECTOR/MOUNTING FLANGE DETAIL SHEETS FOR C

22、OMPATIBILITY SINCE SOME CONNECTOR SHELL SIZES AND CLASSES MAY NOT BE APPLICABLE. SPECIFICATION NOTES: 1. A CHANGE BAR (|) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.