SAE AS 85049 80C-2011 CONNECTOR ACCESSORIES ELECTRICAL DUMMY CONTACT SIZES 16 12 AND 8 CATEGORY 7 (FOR MIL-DTL-38999 CONNECTORS)《规格16 12和8类别7平衡触点电连接器配件(MIL-DTL-38999连接器)》.pdf

《SAE AS 85049 80C-2011 CONNECTOR ACCESSORIES ELECTRICAL DUMMY CONTACT SIZES 16 12 AND 8 CATEGORY 7 (FOR MIL-DTL-38999 CONNECTORS)《规格16 12和8类别7平衡触点电连接器配件(MIL-DTL-38999连接器)》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 85049 80C-2011 CONNECTOR ACCESSORIES ELECTRICAL DUMMY CONTACT SIZES 16 12 AND 8 CATEGORY 7 (FOR MIL-DTL-38999 CONNECTORS)《规格16 12和8类别7平衡触点电连接器配件(MIL-DTL-38999连接器)》.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARD CONNECTOR ACCESSORIES, ELECTRICAL, DUMMY CONTACT, SIZES 16, 12 AND 8, CATEGORY 7 (FOR MIL-DTL-38999 CONNECTORS) AS85049/80Copyright 2011 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form o

2、r by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/w

3、ww.sae.org ISSUED 2000-06REVISED 2011-07THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C1 REV.CFEDERAL SUPPLY CLASS 5935 AS85049/80SHEET 1 OF 5REV. CPROCUREMENT SPECIFICATION: NONESAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineeri

4、ng sciences. Theuse ofthis report is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirmed, rev

5、ised, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS85049/80CRATIONALE REVISION IS REQUIRED TO SPECIFY A SEALING BOOT FOR CERTAIN INSERTS TO MAINTAIN THE ENVIRONMEN

6、TAL SEALING CAPABILITY OF THE CONNECTOR. NOTICE THE REQUIREMENTS FOR ACQUIRING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION SHEET AND THE LATEST ISSUE OF SAE AS85049. INCH mm INCH mm .002.003.004.010.015.020.029.0400.050.080.100.250.380.510.741.02.050 .095 .130 .182 .205 .237 .27

7、1 1.506 1.27 2.41 3.30 4.62 5.21 6.02 6.88 38.25 FIGURE 1 - DIMENSIONS AND CONFIGURATION FOR SIZE 12 CONTACTS Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS85049/80SHEET 2 OF 5

8、REV. CCONNECTOR ACCESSORIES, ELECTRICAL, DUMMY CONTACT, SIZES 16, 12 AND 8, CATEGORY 7 (FOR MIL-DTL-38999 CONNECTORS) INCH mm INCH mm .003.004.010.015.020.029.040.141.151.1550.080.100.250.380.510.741.023.583.843.94.217 .219 .258 .271 .276 .313 .316 .810 .840 1.506 5.56 5.56 4.62 6.88 7.01 7.95 8.03

9、20.57 21.34 38.25 FIGURE 2 - DIMENSIONS AND CONFIGURATION FOR SIZE 8 CONTACTS Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS85049/80SHEET 3 OF 5REV. CCONNECTOR ACCESSORIES, ELE

10、CTRICAL, DUMMY CONTACT, SIZES 16, 12 AND 8, CATEGORY 7 (FOR MIL-DTL-38999 CONNECTORS) INCH mm INCH mm .003.004.010.015.020.029.040.141.151.1550.080.100.250.380.510.741.023.583.843.94.217 .219 .258 .271 .276 .313 .316 .810 .840 1.506 5.56 5.56 4.62 6.88 7.01 7.95 8.03 20.57 21.34 38.25 FIGURE 3 - DIM

11、ENSIONS AND CONFIGURATION FOR SIZE 16 CONTACTS NOTES: 1. DIMENSIONS ARE IN INCHES. 2. METRIC EQUIVALENTS ARE GIVEN FOR GENERAL INFORMATION ONLY. 3. BREAK ALL SHARP EDGES. 4. DUMMY CONTACT SHALL BE FREE OF FLASH AND BURRS. 5. UNLESS OTHERWISE SPECIFIED, TOLERANCES SHALL BE: XX = .01; XXX = .005; ANGU

12、LAR X DEGREES = 1 DEGREE; X DEGREES XX = 0 DEGREES 30. REQUIREMENTS: DESIGN AND CONSTRUCTION: DIMENSIONS AND CONFIGURATION: SHALL BE IN ACCORDANCE WITH FIGURE 1 FOR SIZE 12, FIGURE 2 FOR SIZE 8 AND FIGURE 3 FOR SIZE 16. MATERIALS: PLASTIC ROD, MOLDED, AND EXTRUDED: TEMPERATURE LIMIT 200 C MINIMUM. P

13、OLYTETRAFLUOROETHYLENE PER ASTM D 1710. FLUORINATED ETHYLENE PROPYLENE (FEP). PERFLUOROALKOXY (PFA). Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS85049/80SHEET 4 OF 5REV. CCON

14、NECTOR ACCESSORIES, ELECTRICAL, DUMMY CONTACT, SIZES 16, 12 AND 8, CATEGORY 7 (FOR MIL-DTL-38999 CONNECTORS) COLOR: SIZE 16: BLUE, COLOR TO BE IN ACCORDANCE WITH EIA RS359. SIZE 12: YELLOW, COLOR TO BE IN ACCORDANCE WITH EIA RS359. SIZE 8: GREEN, COLOR TO BE IN ACCORDANCE WITH EIA RS359. INSULATION

15、RESISTANCE: SHALL BE 100 MEGOHMS MINIMUM AT 500 V DC WHEN TESTED IN ACCORDANCE WITH EIA 364-21, USING FLAT PROBES PLACED ON OPPOSITE ENDS OF THE DUMMY CONTACT. TOOLS: GAUGE SIZE INSTALLING TOOLS REMOVAL TOOLS SIZE 16 M81969/14-03 M81969/14-03 SIZE 12 M81969/14-04 M81969/14-04 SIZE 8 1/ M81969/14-06

16、M81969/14-06 1/ SEE APPLICATION NOTE 3 AND FIGURE 4. PART OR IDENTIFYING NUMBER (PIN): SEE EXAMPLE BELOW: EXAMPLE: M85049/ 80 -16 BASIC PART NUMBER SPECIFICATION SHEET DASH NUMBER APPLICATION NOTES: NOTE 1: -16 IS FOR USE IN MIL-DTL-38999, SERIES I, III, OR IV CONNECTORS IN SIZE 16 CONTACT CAVITIES,

17、 -12 IS FOR USE IN MIL-DTL-38999, SERIES I, III, OR IV CONNECTORS IN SIZE 12 CONTACT CAVITIES, -8 IS FOR USE IN MIL-DTL-38999, SERIES I, III, OR IV CONNECTORS IN SIZE 8 CAVITIES. NOTE 2: THE -16, -12 AND -8 DUMMY CONTACTS ARE TO BE USED IN LIEU OF CONTACTS AND SEALING PLUGS IN UNWIRED CONTACT CAVITI

18、ES FOR BOTH PIN AND SOCKET INSERTS. NOTE 3: THE SIZE 8 DUMMY CONTACT REQUIRES AN ADDITIONAL BOOT FOR THE FOLLOWING INSERT ARRANGEMENT 17-2, 19-18, 21-75, 25-7, 25-8, 25-46, AND 25-90 IN ORDER TO SEAL THE CAVITY. BOOT SUPPLIED BY THE CONNECTOR MANUFACTURER. (SEE FIGURE 4) Copyright SAE International

19、Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS85049/80SHEET 5 OF 5REV. CCONNECTOR ACCESSORIES, ELECTRICAL, DUMMY CONTACT, SIZES 16, 12 AND 8, CATEGORY 7 (FOR MIL-DTL-38999 CONNECTORS) FIGURE 4 SEALING BOO

20、T CONFIGURATION QUALIFICATION: SEE AS85049, CATEGORY 7. EXAMINATION OF PRODUCT IS THE ONLY APPLICABLE TEST. QUALIFICATION IS REQUIRED FOR U.S. GOVERNMENT PROCUREMENT. SPECIFICATION NOTES: 1. A CHANGE BAR (|) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNI

21、CAL REVISIONS, NOT EDITORIAL CHANGES HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-