SAE AS 81914 7-2011 TUBING PLASTIC FLEXIBLE CONVOLUTED WITH INTEGRAL BRAID (S)《一体化编织(S)回旋状柔性塑料管》.pdf

《SAE AS 81914 7-2011 TUBING PLASTIC FLEXIBLE CONVOLUTED WITH INTEGRAL BRAID (S)《一体化编织(S)回旋状柔性塑料管》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 81914 7-2011 TUBING PLASTIC FLEXIBLE CONVOLUTED WITH INTEGRAL BRAID (S)《一体化编织(S)回旋状柔性塑料管》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD TUBING, PLASTIC, FLEXIBLE, CONVOLUTED WITH INTEGRAL BRAID (S) AS81914/7Copyright 2011 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopyi

2、ng, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED2011-01THIRD ANGLE PROJECTION CUS

3、TODIAN: AE-8/AE-8C1 FEDERAL SUPPLY CLASS 9330 AS81914/7SHEET 1 OF 3 PROCUREMENT SPECIFICATION: AS81914SAE Technical Standards Board Rules provide that: “This report ispublished by SAE toadvance thestate of technicalandengineering sciences. Theuse ofthisreport is entirelyvoluntary, andits applicabili

4、ty and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirmed, revised,orcancelled.SAE invites yourwrittencomments andsuggestions. SAE VALUES

5、YOUR INPUT. TO PROVIDE FEEDBACK ON THIS TECHNICAL REPORT, PLEASE VISIT http:/www.sae.org/technical/standards/AS81914/7 RATIONALE THIS DOCUMENT COMPLETELY REVISED, INCLUDING RE-FORMATTING TO AN AEROSPACE STANDARD (AS) UNDER THE JURISDICTION OF SAE AE8-C1 FROM AN AEROSPACE MATERIAL SPECIFICATION UNDER

6、 THE JURISDICTION OF SAE AMS P COMMITTEE, TO PROPERLY CLASSIFY AND SUPERSEDE AMS-T-81914/7 MATERIAL SPECIFICATION INCLUDING THE INCORPORATION OF COMMENTS RECEIVED FROM GOVERNMENT AND INDUSTRY, UP-DATE SPECIFICATION REFERENCES, ALIGN WITH SAE GUIDELINES AS NEEDED, INCORPORATE MATERIAL UPDATES, CLARIF

7、Y PART NUMBERING, ADD METRICS AND REVIEW FOR KNOWN TECHNICAL PROBLEMS. NOTICE THE REQUIREMENTS FOR ACQUIRING THE TUBING DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE IN EFFECT OF SAE AS81914. FIGURE 1 DIMENSIONS AND CONFIGURATION Copyright SAE International Provided by IHS und

8、er license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS81914/7SHEET 2 OF 3 TUBING, PLASTIC, FLEXIBLE, CONVOLUTED WITH INTEGRAL BRAID (S) TABLE 1 FIGURE 1 DIMENSIONS Dash Number Inside Diameter (I.D.) Ref. (see note 5) MAX Outer Dia.

9、 (O.D.) Single Braid MAX Outer Dia. (O.D.) Double Braid MIN Bend Radius Single Braid MIN Bend Radius Double Braid Approx. Weight Lbs (kg) per 100 Feet (30.5m) Ref. Single Braid Approx. Weight Lbs (kg) per 100 Feet (30.5m) Ref. Double Braid 01 3/16 .390 (9.91) .450 (11.43) .500 (12.70) .75 (19.05) 5.

10、5 (2.49) 8.7 (3.95) 02 29/32 .485 (12.32) .540 (13.72) .750 (19.05) 1.00 (25.40) 7.7 (3.49) 11.7 (5.31) 03 5/16 .510 (12.95) .570 (14.48) .875 (22.23) 1.25 (31.75) 8.7 (3.95) 12.7 (5.76) 04 3/8 .590 (14.99) .650 (16.51) 1.000 (25.40) 1.50 (38.10) 10.4 (4.72) 15.1 (6.85) 05 7/16 .660 (16.77) .720 (18

11、.29) 1.250 (31.75) 2.00 (50.80) 11.3 (5.13) 16.0 (7.26) 06 1/2 .730 (18.54) .780 (19.81) 1.500 (38.10) 2.25 (57.15) 12.8 (5.81) 18.8 (8.53) 07 5/8 .850 (21.59) .900 (22.86) 1.750 (44.45) 2.50 (63.50) 16.3 (7.39) 23.5 (10.66) 08 3/4 1.045 (26.54) 1.095 (27.81) 1.875 (47.63) 2.87 (72.90) 21.1 (9.57) 2

12、8.5 (12.93) 09 7/8 1.170 (29.72) 1.220 (30.98) 2.250 (57.15) 3.25 (82.55) 22.3 (10.10) 29.7 (13.47) 10 1 1.330 (33.78) 1.380 (35.05) 2.500 (63.50) 3.62 (91.95) 25.3 (11.48) 33.8 (15.33) 11 1 1/8 1.460 (37.08) 1.510 (38.35) 2.750 (69.85) 4.00 (101.60) 36.7 (16.65) 55.9 (25.36) 12 1 1/4 1.609 (40.87)

13、1.659 (42.14) 3.000 (76.20) 4.25 (107.95) 38.8 (17.60) 58.0 (26.31) 13 1 1/2 1.920 (48.77) 1.970 (50.04) 3.750 (95.25) 4.37 (111.00) 46.1 (20.91) 66.2 (30.03) 14 1 3/4 2.170 (55.12) 2.220 (56.39) 4.250 (107.95) 4.62 (117.35) 50.6 (22.95) 71.6 (32.48) 15 2 2.420 (61.47) 2.470 (62.74) 4.750 (120.65) 5

14、.25 (133.35) 56.1 (25.45) 78.9 (35.79) NOTES: 1. DIMENSIONS ARE IN INCHES. 2. UNLESS OTHERWISE SPECIFIED TOLERANCES SHALL BE: .XX = .010 (0.25 MM), .XXX = .005 (0.13 MM). 3. METRIC EQUIVALENTS ARE GIVEN FOR GENERAL INFORMATION ONLY AND ARE BASED ON 25.4 MM = 1 INCH. 4. METRIC DIMENSIONS IN PARENTHES

15、ES ARE SHOWN IN MILLIMETERS. REQUIREMENTS: 1. CONVOLUTION TYPE: SEE INDIVIDUAL TUBING DETAIL SHEET AND PART NUMBER EXAMPLE. 2. CONSTRUCTION DETAILS: BRAIDED CONVOLUTED TUBING SHALL CONSIST OF AN INNER CORE AND ONE OR TWO LAYERS OF BRAID. AVAILABLE SIZES, DIMENSIONS AND TOLERANCES, ARE LOCATED IN TAB

16、LE 1. 3. LENGTHS SHALL BE SPECIFIED IN FEET BY THE PROCURING ACTIVITY AND DOES NOT FORM A PART OF THE IDENTIFYING PART NUMBER. MINIMUM ORDER LENGTH SHALL BE 3 FEET (0.914 M) AND THE TUBING ORDER LENGTH TOLERANCES SHALL BE AS SPECIFIED IN TABLE 2. TUBING SHALL BE PROCURED AS COILS. Copyright SAE Inte

17、rnational Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS81914/7SHEET 3 OF 3 TUBING, PLASTIC, FLEXIBLE, CONVOLUTED WITH INTEGRAL BRAID (S) TABLE 2 ORDER LENGTH TOLERANCE ORDER LENGTH RANGE LENGTH IN FEET (

18、METERS) TOLERANCE IN INCHES (MM) 3 12 (0.914 M 3.66 M) + 2.0 / - 0.0 (+ 50.8 MM / - 0.0 MM) 13 50 (3.96 M 15.24 M) + 4.0 / - 0.0 (+ 101.6 MM / - 0.0 MM) 51 AND UP (15.55 M AND UP) + 6.0 / - 0.0 (+ 152.4 MM / - 0.0 MM) 4. BRAID: THE INTEGRAL BRAID SHALL CONSIST OF ONE OR TWO LAYERS OF NICKEL/COPPER O

19、R TIN/COPPER WIRE, 34 AWG IN ACCORDANCE WITH A-A-59569 OR EQUIVALENT. EACH LAYER OF BRAID SHALL HAVE A MINIMUM OPTICAL COVERAGE OF 90%. 5. CONTINUOUS OPERATING TEMPERATURE: SEE INDIVIDUAL TUBING DETAIL SHEETS. 6. COLOR: SEE INDIVIDUAL TUBING DETAIL SHEETS. 7. PHYSICAL PROPERTIES: SEE INDIVIDUAL TUBI

20、NG DETAIL SHEETS. 8. SHELF LIFE: SEE INDIVIDUAL TUBING DETAIL SHEETS. NUMBER OR IDENTIFING NUMBER (PIN). EXAMPLE : M81914 / 7 3 T 2 06 D H HELIX WIRE, OMIT FOR NONE DRAIN HOLES, OMIT FOR NONE DASH NUMBER, TABLE 1 1 = SINGLE LAYER BRAID, 2 = DOUBLE LAYER BRAID T = TIN/COPPER BRAID N = NICKEL/COPPER B

21、RAID TUBING DETAIL SHEET DESIGNATOR (3 = M81914/3 TUBING) SPECIFICATION SHEET BASIC PART NUMBER QUALIFICATION: SEE SAE AS81914 SPECIFICATION NOTES: NOTICE A CHANGE BAR (L) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES

22、, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-