SAE AS 8004-1975 Minimum Performance Standard for Turn and Slip Instrument《转弯倾斜指示仪的最低性能标准》.pdf

《SAE AS 8004-1975 Minimum Performance Standard for Turn and Slip Instrument《转弯倾斜指示仪的最低性能标准》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 8004-1975 Minimum Performance Standard for Turn and Slip Instrument《转弯倾斜指示仪的最低性能标准》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising therefr

2、om, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invites your written comments and suggestions. Copyright 2008 SAE International All rights reserved. No part of this publication may

3、 be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) F

4、ax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org AS 8004 - 2 -3.7 Visibility: Turn and slip indications must be visible from any point within the frustum of a cone the side of which makes an angle of at least 30 degrees with the perpendicular to the dial and the smal

5、l diameter of which is the aperture of the instrument case.3.8 Power Malfunction Indication: For Types II and III instruments, means must be incorporated in the instrument to indicate the loss of adequate power to the rate-of-turn gyro and primary signal voltages to the pointer in remote instruments

6、. The indicating means must indicate a failure or malfunction in a positive manner.3.9 Reflectance, Cover Glass: The total reflectance of the instrument cover glass including the integral lighting wedge, if applicable, shall not exceed 10% of the incident light. This reflectance applies over the vis

7、ible light spectrum from 450 milli-microns to 600 milli-microns, and over an incident solid angle of 60 perpendicular to the viewing plane.4. PERFORMANCE STANDARDS UNDER STANDARD CONDITIONSThe test conditions applicable to a determination of the performance of turn and slip instruments are set forth

8、 in Appendix A of this standard. All instruments shall be tested in accordance with the manufacturers recommendations. The manufacturer shall conduct sufficient tests to prove compliance with these Minimum Performance Standards.4.1 Turn Indicator Starting: Instrument performance must be achieved wit

9、hin three (3) minutes after normal rated power is applied for both air and electric operated instruments. By application of 50% of rated suction of air operated indicators and 80% of rated voltage for electrically operated indicators, the gyro must start, continue to rotate, and provide an adequate

10、indication of turning motions. However, under the reduced power conditions, the turn indicator sensitivity and damping requirements do not apply. If the instrument incorporates a gyro speed monitoring device which provides a positive indication when the gyro speed is below that necessary to meet ins

11、trument performance, the starting time may exceed three minutes.4.2 Turn Indicator Characteristics:(a) Sensitivity When the instrument is operating under rated power and subjected to the turning rates specified about the vertical axis, the turn instrument deflection, in inches or millimetres, must b

12、e within the limits of either Column A or B. The indicator movement must be smooth.Column A values pertain to instruments set to indicate a standard rate of turn (180 per minute)with one indicator unit deflection. Column B provides double this displacement for indicators providing increased sensitiv

13、ity.For instruments possessing display features such that the dimensional characteristics prescribed by Columns A and B do not apply, the applicant may demonstrate that the indicator can reliably indicate the prescribed rates of turn with clarity and accuracy equivalent to that specified in Column A

14、 or B.Rate of Turn (Degrees per Minute)Deflection of IndicatorColumn A Column BInches mm Inches mm036901803600 0.0151/32 1/645/64 1/325/32 1/325/16 1/160 0.40.8 0.42.0 0.84.0 0.87.9 1.60 0.0151/16 1/645/32 1/325/16 1/169/16 1/80 0.41.6 0.44.0 0.87.9 1.614.3 3.2AS 8004- 3 -(b) Damping The time for th

15、e turn indicator or index to return to the zero mark without crossing the zero mark must be at least two but not more than four seconds, when the instrument is suddenly stopped after being rotated about its vertical axis at a rate that causes full-scale pointer or index deflection.4.3 Slip Indicator

16、 Characteristics: The slip indicator must operate freely when the instrument is rotated about its longitudinal axis with the dial vertical. The range of slip indicators must be at least 7 degrees either side of vertical. With the instrument in its normal position for mounting, the position of the in

17、dicator must be zero (0) 1/32 inch (0 0.8 mm).(a) Damping. The time for the slip indicator to move from the zero position of the slip indication to the test position must not be less than 0.2 seconds following a sudden rotation of the instrument from a position of 12 degrees bank through the vertica

18、l to 12 degrees of opposite bank.(b) Slip Indicator Filling. Instruments using a liquid as a damping medium for the slip indicator must be so designed and filled that no part of an air bubble will be visible from a point 12 inches (30.5 cm) directly in front of the instrument when the instrument is

19、rotated to an angle of roll of 45 degrees.5. PERFORMANCE STANDARDS UNDER ENVIRONMENTAL CONDITIONSUnless otherwise specified herein, the measurement procedures applicable to a determination of the performance of turn and slip instruments under environmental conditions are set forth in Radio Technical

20、 Commission for Aeronautics (RTCA) Document No. DO-138, entitled “Environmental Conditions and Test Procedures for Airborne Electronic/Electrical Equipment and Instruments” dated 27 June 1968. Performance tests which must be made after subjection to test environments may be made after exposure to se

21、veral environmental conditions. The order of tests must be in accordance with DO-138. The test procedures specified or referenced are satisfactory for use in determining the performance of turn and slip instruments under normal and extreme environmental conditions. Alternate approved test procedures

22、 that provide equivalent results may be used.5. 1 Temperature:(a) Low temperature. When subjected to the tests of DO-138, the instrument must operate electrically and mechanically and the requirements of paragraphs 4.1 through 4.3 of this standard must be met. The time required for the slip indicato

23、r to come to the rest position must not exceed four seconds as required by paragraph 4.3(a).(b) High temperature. When subjected to the tests of DO-138, the instrument must operate electrically and mechanically and the requirements of paragraph 4.1 through 4.3 of this standard must be met.5.2 Altitu

24、de: When subjected to the tests of DO-138, the instrument must operate electrically and mechanically and the requirements of 4.1 through 4.3 of this standard must be met.5.3 Humidity: When subjected to the tests of DO-138, standard humidity environment, the requirements of 4.1 through 4.3 of this st

25、andard must be met.5.4 Vibration: When the instrument is tested in accordance with DO-138, standard vibration requirements, it must operate electrically and mechanically and the requirements of 4.1 through 4.3 must be met. After subjection to this test, the requirements of 4.1 through 4.3 of this st

26、andard must be met.AS 8004 - 4 -5.5 Power Input:(a) Electrical input variation test(1) When the instrument is subjected to the tests in DO-138, it must meet the requirements of 4.1 through 4.3 of this standard.(b) Low voltage test(1) When the instrument is subjected to the tests in DO-138, it must o

27、perate electrically and mechanically and degradation of performance is permissible. The degree of performance degradation shall be specified by the manufacturer.(c) Hydraulic/pneumatic input variation test(1) When the instrument is subjected to the tests in DO-138, it must operate and degradation of

28、 performance is permissible. The degree of performance degradation shall be specified by the manufacturer.5. 6 Conducted Voltage Transients:.(a) Intermittent transients - The instrument shall be subjected to the tests of DO-138, and shall meet the requirements of 4.1 through 4.3 of this standard.(b)

29、 Repetitive transients - The instrument shall be subjected to the tests of DO-138, and shall meet the requirements of 4. 1 through 4.3 of this standard.(c) Interconnecting wiring induced transients - The instrument shall be subjected to the tests ofDO-138, and shall meet the requirements of 4.1 thro

30、ugh 4.3 of this standard.(d) Instruments operated from AC power - The instrument shall be subjected to the tests of DO-138, and shall meet the requirements of 4.1 through 4.3 of this standard.5.7 Conducted Audio Frequency Suseptibility Test: The instrument shall be subjected to the tests of DO-138,

31、and shall meet the requirement of 4.1 through 4.3 of this standard.5.8 Audio Frequency Magnetic Field Susceptibility: The instrument shall be subjected to the tests of DO-138, and shall meet the requirements of 4.1 through 4.3 of this standard.5.9 Radio Frequency Susceptibility: The instrument shall

32、 be subjected to the tests of DO-138, and shall meet the requirements of 4.1 through 4.3 of this standard.5.10 Emission of Radio Frequency Energy and Magnetic Effect: The instrument shall be tested in accordance with radio frequency interference and magnetic effect requirements of DO-138, for the ca

33、tegory to which the instrument is designed. As applicable, the instrument shall be tested in accordance with the magnetic effect paragraph.5.11 Explosion: Instruments which are to be marked Explosion Category E must be tested in accordance with DO-138.5.12 Waterproofness: Instruments which are to be

34、 marked Waterproofness Category W must be tested in accordance with DO-138. Following this test, the instrument must meet the requirements of 4.1 through 4.3 of this standard.AS 8004- 5 -5.13 Hydraulic Fluid: Instruments which are to be marked Hydraulic Fluid Category H must be tested in accordance

35、with DO-138. Following this test, the instrument must meet the requirements of 4.1 through 4.3 of this standard.5.14 Sand and Dust: Instruments which are to be marked Sand and Dust Category D must be tested in accordance with DO-138. Following this test, the instrument must meet the requirements of

36、4.1 through 4.3 of this standard.5.15 Fungus Resistance: Instruments which are to be marked Fungus Resistance Category F must be tested in accordance with DO-138. Following this test, the instrument must meet the requirement of 4.1 through 4.3 of this standard.5.16 Salt Spray: Instruments which are

37、to be marked Salt Spray Category S must be tested in accordance with DO-138. Following this test, the instrument must meet the requirements of 4.1 through 4.3 of this standard.PREPARED BYSAE COMMITTEE A-4, AIRCRAFT INSTRUMENTSAS 8004 - 6 -APPENDIX AStandard Test ConditionsThe following conditions of

38、 tests are applicable to the instrument tests specified herein:Atomopheric Conditions Unless otherwise specified, all tests required by this standard must be conducted at an atmospheric pressure of approximately 29.92 inches (760 mm) of mercury, an ambient temperature of approximately +77F (+25C), a

39、nd a relative humidity of not greater than 85 percent. When tests are conducted with the atmospheric pressure of temperature substantially different from these valves, allowance must be made for the variation from the specified conditions.Vibration to Minimize Friction Unless otherwise specified, al

40、l tests for performance may be conducted with the instrument subjected to a vibration of 0.002 to 0.005 inches (0.05 to 0.13 mm) double amplitude at a frequency of 25 to 33 Hertz. The term double amplitude as used herein indicates the total displacement from positive maximum to negative maximum.Power Conditions Unless otherwise specified, all tests must be conducted at the power rating recommended by the manufacturer.Mounting Position Unless otherwise specified, all tests must be made with the instrument (indicator, gyroscope, etc.) mounted in their normal operating position.