SAE AS 7106 5-1995 National Aerospace and Defense Contractors Accreditation Program Self-Release Agreements - Requirements《国家航空航天和国防合同方授信项目自动解除协议的要求》.pdf

《SAE AS 7106 5-1995 National Aerospace and Defense Contractors Accreditation Program Self-Release Agreements - Requirements《国家航空航天和国防合同方授信项目自动解除协议的要求》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 7106 5-1995 National Aerospace and Defense Contractors Accreditation Program Self-Release Agreements - Requirements《国家航空航天和国防合同方授信项目自动解除协议的要求》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、The Engineering Society For Advancing Mobility Land Sea Air and Space I N T E R N A T I O N A L400 Commonwealth Drive, Warrendale, PA 15096-0001AEROSPACESTANDARDCopyright 1995 Society of Automotive Engineers, Inc.All rights reserved.Printed in U.S.ASAE Technical Standards Board Rules provide that: “

2、This report is published by SAE to advance the state of technical andengineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use ,including any patent infringement arising therefrom, is the sole responsibility of the user.”SAE revi

3、ews each technical report at least every five years at which time it may be reaffirmed, revised, or cancelled. SAE invit esyour written comments and suggestions.Submitted for recognition as an American National StandardAS7106/5Issued 1995-03NATIONAL AEROSPACE AND DEFENSECONTRACTORS ACCREDITATION PRO

4、GRAMSELF-RELEASE AGREEMENTS - REQUIREMENTS1.SCOPEThis Aerospace Standard is to be used as a supplement to either PRI AC7106 or PRI AC7107 by suppliers that have customer approval for self-release of finished product. This standard applies to suppliers seeking NADCAP General Quality Systems accredita

5、tion who are required by contract to conform to the requirements of Self-Release Agreements.2.APPLICABLE DOCUMENTSThe following publications form a part of this specification to the extent specified herein. The latest issue of SAE and PRI publications shall apply.2.1SAE Publications:Available from S

6、AE, 400 Commonwealth Drive, Warrendale, PA 15086-0001.AS7106National Aerospace and Defense Contractors Accreditation Program (NADCAP) - Quality Program RequirementsAS7107National Aerospace and Defense Contractors Accreditation Program (NADCAP) - Inspection System RequirementsCopyright SAE Internatio

7、nal Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-SAE AS7106/5- 2 -2. 2 PRI Publications:Available from Performance Review Institute, 163 Thornhill Road, Warrendale, PA 15086-7527.AC710 6 NADCAP - Quality Program Audit Criteria

8、AC710 7 NADCAP - Inspection System Audit Criteria3 .REQUIREMENTS3. 1 The self-release privileges shall be formalized through a mutual supplier/customer agreement, plan, or procedure.3. 2 The supplier shall maintain a copy of their customer(s) self-release agreement, plan, or procedure.3. 3 The suppl

9、ier shall release material in accordance with criteria specified in the self-release agreement, plan, or procedure.3. 4 If required by the self-release agreement, plan, or procedure, the supplier personnel shall be certified or approved to release product.3.4. 1 Supplier personnel certifications sha

10、ll be current.3.4. 2 Self-release stamps/signatures shall be under a system of control.3. 5 If required by the self-release agreement, plan, or procedure, the supplier shall qualify their product(s) prior to initial and/or follow-on shipments.3. 6 There shall be documented evidence available to atte

11、st that product qualification requirements are being adhered to.3. 7 The supplier shall maintain documentation that reflects compliance to all the procedural aspects of the self-release agreement, plan, or procedure.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-