SAE AS 6173 2-2012 CUTTING TOOL ELECTRICAL WIRE CUTTING WITH GRIPPING TEETH HAND ACTUATED TYPE I WIRE SIZES 26 THROUGH 10《手动I型电线尺寸26至10带握齿电火花线切割的电气切削工具》.pdf

《SAE AS 6173 2-2012 CUTTING TOOL ELECTRICAL WIRE CUTTING WITH GRIPPING TEETH HAND ACTUATED TYPE I WIRE SIZES 26 THROUGH 10《手动I型电线尺寸26至10带握齿电火花线切割的电气切削工具》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 6173 2-2012 CUTTING TOOL ELECTRICAL WIRE CUTTING WITH GRIPPING TEETH HAND ACTUATED TYPE I WIRE SIZES 26 THROUGH 10《手动I型电线尺寸26至10带握齿电火花线切割的电气切削工具》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD CUTTING TOOL, ELECTRICAL, WIRE CUTTING WITHGRIPPING TEETH, HAND ACTUATED, TYPE I, WIRESIZES 26 THROUGH 10 AS6173/2Copyright 2012 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by an

2、y means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.

3、org ISSUED 2012-12THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C2 FEDERAL SUPPLY CLASS 5970 AS6173/2SHEET 1 OF 2 PROCUREMENT SPECIFICATION: AS6173SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis repor

4、t is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabilized, orcancelled. S

5、AE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS6173/2 RATIONALE THIS DOCUMENT PROVIDES THE REQUIREMENTS FOR A WIRE CUTTING TOOL TO CUT AIRCRAFT WIRING SIZES 10 THROUGH 26 AWG. NOT

6、ICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS DOCUMENT AND THE LATEST ISSUE OF SAE AS6173. FIGURE 1 - BASIC WIRE CUTTER TOOL 1.60 MAX.61 MAX1.28 6.00 MAX .25 MAX .58 TYP.7 MAXCopyright SAE International Provided by IHS under license with SAENot for Re

7、saleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS6173/2 SHEET 2 OF 2 CUTTING TOOL, ELECTRICAL, WIRE CUTTING WITH GRIPPING TEETH, HAND ACTUATED, TYPE I, WIRE SIZES 26 THROUGH 10 REQUIREMENTS: 1. DESIGN: OUTLINE CONFIGURATION OPTIONAL WITHIN MAXIMUM DIMENSI

8、ONS SHOWN FOR A CLOSED HANDLE POSITION. DIMENSIONS ARE IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES ARE .005 (0.13 MM) FOR THREE PLACE DECIMALS AND .01 (0.25 MM) FOR TWO PLACE DECIMALS. 2. MATERIALS: JAWS: 50 POINT CARBON MIN. ALLOY STEEL; HEAT TREAT ROCKWELL C43-54. CUTTER SURFACES: SHALL HAVE

9、 A MINIMUM HEAT TREAT OF ROCKWELL C53-C58. HANDLES: S 40 POINT CARBON MIN. ALLOY STEEL GRIPS: PLASTIC, RUBBER (COLOR - YELLOW). 3. FINISH: JAW - BLACK OXIDE HANDLES - BLACK OXIDE 4. TOOL ASSEMBLY WEIGHT: COMPLETE ASSEMBLY HANDLES, GRIPS, AND JAWS SHALL NOT WEIGH IN EXCESS OF 1.0 POUNDS (0.45 KG). 5.

10、 PART NUMBER: M6173/2-01 DESIGNATES THE ENTIRE ASSEMBLY INCLUDING THE HANDLE, GRIPS, AND JAWS. 6. TOOL OPERATIONAL CHARACTERISTICS: A SPRING SHALL BE PROVIDED TO FULLY OPEN THE JAWS AND HANDLES WHEN THE LOCK IS NOT ENGAGED. A MAXIMUM FORCE OF 35 POUNDS SHALL BE REQUIRED TO CLOSE THE CUTTER NOT INCLU

11、DING THE FORCE TO CUT INDIVIDUAL WIRES. 7. CUTTER COMPRESSION FORCE: REQUIRED. 8. CUTTING PERFORMANCE CHARACTERISTICS: REQUIRED. 9. SHOCK CHARACTERISTICS: REQUIRED 10. HUMIDITY CHARACTERISTICS: REQUIRED 11. LIFE CHARACTERISTICS: REQUIRED (CUTTING CYCLES SHALL BE 5000) 12. WORKMANSHIP: REQUIRED APPLI

12、CATION NOTES: 1. THIS WIRE CUTTER IS DESIGNED TO BE USED FOR CUTTING AIRCRAFT WIRING SUCH AS AS22759 WITH TIN, NICKEL AND SILVER COATED CONDUCTORS OF COPPER, AND HIGH STRENGTH OR ULTRA HIGH STRENGTH COPPER ALLOY. SPECIFICATION NOTES: 1. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIE

13、NCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-