SAE AS 6055-2001 Drum Metal Reusable Shipping and Storage (Cap from 88 to 510 Cubic Inches)《FSC8110可重复使用金属辊筒 运输和存储工具(第88至510立方英寸)》.pdf
《SAE AS 6055-2001 Drum Metal Reusable Shipping and Storage (Cap from 88 to 510 Cubic Inches)《FSC8110可重复使用金属辊筒 运输和存储工具(第88至510立方英寸)》.pdf》由会员分享,可在线阅读,更多相关《SAE AS 6055-2001 Drum Metal Reusable Shipping and Storage (Cap from 88 to 510 Cubic Inches)《FSC8110可重复使用金属辊筒 运输和存储工具(第88至510立方英寸)》.pdf(17页珍藏版)》请在麦多课文档分享上搜索。
1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there
2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2017 SAE International All rights reserved. No part of this p
3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497
4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS6055 AEROSPACE STANDARD AS6055 Issued 2001-12 Reaffirmed 2017-11 Drum, Metal Reusable, Shippi
5、ng and Storage (Cap. from 88 to 510 Cubic Inches) FSC 8110 RATIONALE AS6055 has been reaffirmed to comply with the SAE Five-Year Review policy. NOTICEThis document has been taken directly from U.S. Military Specification MIL-D-6055D, Amendment 1 and contains only minor editorial and format changes r
6、equired to bring it into conformance with the publishing requirements of SAE technical standards. The initial release of this document is intended to replace MIL-D-6055D, Amendment 1. Any part numbers established by the original specification remain unchanged.The original Military Specification was
7、adopted as an SAE standard under the provisions of the SAE Technical Standards Board (TSB) Rules and Regulations (TSB 001) pertaining to accelerated adoption of government specifications and standards. TSB rules provide for (a) the publication of portions of unrevised government specifications and s
8、tandards without consensus voting at the SAE Committee level, and (b) the use of the existing government specification or standard format.Under Department of Defense policies and procedures, any qualification requirements and associated qualified products lists are mandatory for DOD contracts. Any r
9、equirement relating to qualified products lists (QPLs) has not been adopted by SAE and is not part of this SAE technical document.1. SCOPE:1.1 Scope:This specification covers the requirements for new reusable cylindrical drums consisting of body, cover, gasket, and closing device(s) to be used as in
10、terior and exterior shipping containers.1.2 Classification:Drums, metal, shipping, and storage, shall be of the following types, classes, and sizes as specified (see MS24347 and 6.2).Type I - Formed DrumType II - Drawn DrumClass A - Aluminum Alloy DrumClass S - Steel DrumStyle D - Dome CoverStyle R
11、- Recessed CoverSize No. 1 - 88 Cubic Inch CapacitySize No. 2 - 167 Cubic Inch CapacitySize No. 3 - 149 Cubic Inch CapacitySize No. 4 - 224 Cubic Inch CapacitySize No. 5 - 282 Cubic Inch CapacitySize No. 6 - 340 Cubic Inch CapacitySize No. 7 - 425 Cubic Inch CapacitySize No. 8 - 510 Cubic Inch Capac
12、ity2. REFERENCED DOCUMENTS:2.1 Government documents:2.1.1 Specifications, standards, and handbooks: The following specifications, standards, and handbooks form a part of this specification to the extent specified herein. Unless otherwise specified, the issues of these documents shall be those listed
13、 in the issue of the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation.SPECIFICATIONSFederalTT-P-1757 Primer Coating, Zinc Chromate, Low Moisture SensitivityTT-E-485 Enamel; Semi-Gloss, Rust-InhibitingPPP-B-636 Box, FiberboardSAE I
14、NTERNATIONAL AS6055 Page 2 of 17_ 2.1.1 (Continued):PPP-C-1120 Cushioning Material, Uncompressed Bound Fiber for PackagingPPP-C-1752 Cushioning Material, Packaging, (Unicellular Polyethylene Foam, Flexible)MilitaryMIL-P-116 Preservation, Methods ofMIL-R-6855 Synthetic Rubber Sheet, Strips, Molded or
15、 Extruded ShapesMIL-A-8625 Anodic Coatings, For Aluminum and Aluminum AlloysMIL-I-26860 Indicator, Humidity, Plug, Color ChangeSTANDARDSFederalFED STD-101 Test Procedures for Packaging MaterialsFED-STD-595 ColorsMilitaryMIL-STD-105 Sampling Procedures and Tables for Inspection by AttributesMIL-STD-1
16、29 Marking for Shipment and StorageMIL-STD-130 Identification Marking of US Military PropertyMIL-STD-147 Palletized Unit LoadsMIL-STD-2073 DOD Material Procedures for Development and Application of Packaging RequirementsMS24347 Drum, Metal, Reusable Shipping and Storage(Copies of specifications, sta
17、ndards, handbooks, drawings, publications, and other Government documents required by contractors in connection with specific acquisition _ should be obtained from the contracting activity or as directed by the contracting activity.)2.2 Other publications:The following document(s) form a part of thi
18、s specification to the extent specified herein. Unless otherwise specified, the issues of the documents which are DOD adopted shall be those listed in the issue of the DODISS specified in the solicitation. Unless otherwise specified, the issues of documents not listed in the DODISS shall be the issu
19、e of the nongovernment documents which is current on the date of the solicitation.American Society for Testing and Materials (DOD adopted)ASTM A109 Steel, Strip, Carbon, Cold Rolled, Spec. forASTM A366 Steel, Sheet, Carbon, Cold Rolled, Commercial Quality, Spec. forSAE INTERNATIONAL AS6055 Page 3 of
20、 17_ 2.2 (Continued):ASTM D3951 Commercial Packaging, Practice forASTM B117 Salt Spray (Fog) Testing, Standard forASTM D610 Evaluating Degree of Rusting on Painted Steel Surfaces(Application for copies should be addressed to American Society for Testing and Materials, 1916 Race Street, Philadelphia,
21、 PA 19103)(Nongovernment standards and other publications are normally available from the organizations which prepare or which distribute the documents. These documents also may be available in or through libraries or other informational service.)2.3 Order of precedence:In the event of a conflict be
22、tween the text of this specification and the references cited herein (except for associated detail specifications, specification sheets or MS standards), the text of this specification shall take precedence. Nothing in this specification, however, shall supersede applicable laws and regulations unle
23、ss a specific exemption has been obtained.3. REQUIREMENTS:3.1 MS sheets:The individual item requirements shall be as specified herein and in accordance with the applicable MS sheet. In the event of any conflict between the requirements of this specification and the MS sheet, the latter shall govern.
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SAEAS60552001DRUMMETALREUSABLESHIPPINGANDSTORAGECAPFROM88TO510CUBICINCHESFSC8110 重复使用 金属 运输 存储 工具 88

链接地址:http://www.mydoc123.com/p-1025058.html