书签分享收藏举报版权申诉 / 17

立即下载加入VIP,交流精品资源

当前位置：首页 > 标准规范 > 国际标准 > 其他 > SAE AS 5861A-2015 Retainers (Back-Up Rings) Hydraulic and Pneumatic Polytetrafluoroethylene Resin Solid Static Gland.pdf

SAE AS 5861A-2015 Retainers (Back-Up Rings) Hydraulic and Pneumatic Polytetrafluoroethylene Resin Solid Static Gland.pdf

上传人：figureissue185

文档编号：1024975

上传时间：2019-03-21

格式：PDF

页数：17

大小：89.52KB

《SAE AS 5861A-2015 Retainers (Back-Up Rings) Hydraulic and Pneumatic Polytetrafluoroethylene Resin Solid Static Gland.pdf》由会员分享，可在线阅读，更多相关《SAE AS 5861A-2015 Retainers (Back-Up Rings) Hydraulic and Pneumatic Polytetrafluoroethylene Resin Solid Static Gland.pdf（17页珍藏版）》请在麦多课文档分享上搜索。

1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there

2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2015 SAE International All rights reserved. No part of this p

3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497

4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AS5861A AEROSPACE STANDARD AS5861 REV. A Issued 2005-12 Revised 2015-07Supersedin

5、g AS5861 Retainers, (Back-Up Rings), Hydraulic and Pneumatic, Polytetrafluoroethylene Resin, Solid, Static Gland RATIONALE Revision A adds tables in metric units and adds complete part numbers in tables and the ASME reference publication. 1. SCOPE This SAE Aerospace Standard (AS) covers solid polyte

6、trafluoroethylene (PTFE) retainers (back-up rings) for use in static glands in accordance with AS5857. They are for use in hydraulic and pneumatic system components as anti-extrusion devices in conjunction with O-rings, packings and other elastomeric seals. Because of the construction of groove dime

7、nsions, back-ups specific to rod applications are designated “R” - Rod (Female), back-ups specific to piston applications are designated “P” - Piston (Male). Retainers specified herein have been designed for a temperature range of -65 to 275 F (-54 to 135 C) and a nominal operating pressure of 3000

8、psi (20 684 kPa) for code 09 material and 5000 psi (34 474 kPa) for code 10 material. Material codes are based on AMS3678 material types. 2. REFERENCES 2.1 Applicable Documents The following publications form a part of this document to the extent specified herein. The latest issue of SAE publication

9、s shall apply. The applicable issue of other publications shall be the issue in effect on the date of the purchase order. In the event of conflict between the text of this document and references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes

10、applicable laws and regulations unless a specific exemption has been obtained. 2.1.1 SAE Publications Available from SAE International, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or +1 724-776-4970 (outside USA), www.sae.org. AS5857 Gland Design, O-r

11、ing and Other Elastomeric Seals, Static Applications AS5860 Retainers, (Back-Up Rings), Hydraulic and Pneumatic, Polytetrafluoroethylene Resin, Single Turn, Static Gland SAE INTERNATIONAL AS5861A Page 2 of 17 AMS3678/9 Type 9 Virgin Polytetrafluoroethylene (PTFE) Moldings with Pigment for AS4716 and

12、 AS5857 Backup Rings AMS3678/10 Type 10 Virgin Polytetrafluoroethylene (PTFE) Moldings or Extrusions with 15% Carbon Fiber 2.1.2 ASME Publications Available from ASME, P.O. Box 2900, 22 Law Drive, Fairfield, NJ 07007-2900, Tel: 800-843-2763 (U.S./Canada), 001-800-843-2763 (Mexico), 973-882-1170 (out

13、side North America), www.asme.org. ASME Y 14.5-2009 Dimensioning and Tolerancing 2.1.3 U.S. Government Publications Copies of these documents are available online at http:/quicksearch.dla.mil. MIL-STD-2073-1 Standard Practice for Military Packaging 3. TECHNICAL REQUIREMENTS 3.1 Material 3.1.1 Code 0

14、9, Virgin PTFE with Pigment Parts made to material code 09 of this standard shall conform to AMS3678/9, Pigmented Virgin PTFE, Molded. “R” (Rod) applications shall be green per AMS3678/9. “P” (Piston) applications shall be brown per AMS3678/9. 3.1.2 Code 10, PTFE With 15% Carbon Fiber Parts made to

15、material code 10 of this standard shall conform to AMS3678/10, Virgin PTFE Moldings or Extrusions with 15% Carbon Fiber. Color shall be black or dark gray. 3.2 Dimensional Requirements Parts shall conform to Figure 1 and the dimensions listed in Table 1. NOTE: Dimensions are based on nominal ring “O

16、D” equal to minimum A for piston back-up rings and nominal ring “ID” equal to maximum B for rod back-up rings. A and B dimensions are from AS5857. Radial width “W” is based on a net fit in the gland at maximum material condition with all features concentric. IDTW ODSee Tables 1A and 1B for dimension

17、s Figure 1 - Controlled features SAE INTERNATIONAL AS5861A Page 3 of 17 3.2.1 Surfaces and Edges All surfaces shall be smooth and free from irregularities. Edges shall be clean and sharp. 3.3 Part Number The part number consists of the standard number, the piston or rod code, the material code follo

18、wed by the appropriate three digit dash number taken from Tables 1A or 1B. AS5861 P 10 -123Material CodeDash Number“R“ for RodStandard Number“P“ for PistonExample:Table 1A - AS5861 back up ring dimensions (in inches) Male (Piston) Applications Female (Rod) Applications Part No. OD 0.001 T 0.002 W 0.

19、001 Part No. ID 0.001 T 0.002 W 0.001 AS5861P(XX)-004 0.185 0.054 0.052 AS5861R(XX)-004 0.076 0.054 0.053 AS5861P(XX)-005 0.217 0.054 0.052 AS5861R(XX)-005 0.108 0.054 0.053 AS5861P(XX)-006 0.230 0.054 0.052 AS5861R(XX)-006 0.123 0.054 0.053 AS5861P(XX)-007 0.261 0.054 0.052 AS5861R(XX)-007 0.154 0.

20、054 0.053 AS5861P(XX)-008 0.293 0.054 0.052 AS5861R(XX)-008 0.185 0.054 0.053 AS5861P(XX)-009 0.326 0.054 0.052 AS5861R(XX)-009 0.217 0.054 0.053 AS5861P(XX)-010 0.357 0.054 0.052 AS5861R(XX)-010 0.248 0.054 0.053 AS5861P(XX)-011 0.420 0.054 0.052 AS5861R(XX)-011 0.310 0.054 0.053 AS5861P(XX)-012 0.

21、485 0.054 0.052 AS5861R(XX)-012 0.373 0.054 0.053 AS5861P(XX)-013 0.550 0.054 0.052 AS5861R(XX)-013 0.435 0.054 0.053 AS5861P(XX)-014 0.613 0.054 0.052 AS5861R(XX)-014 0.498 0.054 0.053 AS5861P(XX)-015 0.675 0.054 0.052 AS5861R(XX)-015 0.560 0.054 0.053 AS5861P(XX)-016 0.738 0.054 0.052 AS5861R(XX)-

22、016 0.623 0.054 0.053 AS5861P(XX)-017 0.800 0.054 0.052 AS5861R(XX)-017 0.685 0.054 0.053 AS5861P(XX)-018 0.863 0.054 0.052 AS5861R(XX)-018 0.748 0.054 0.053 AS5861P(XX)-019 0.925 0.054 0.052 AS5861R(XX)-019 0.810 0.054 0.053 AS5861P(XX)-020 0.991 0.054 0.052 AS5861R(XX)-020 0.873 0.054 0.053 AS5861

23、P(XX)-021 1.053 0.054 0.052 AS5861R(XX)-021 0.935 0.054 0.053 OD ID 0.002 0.002 AS5861P(XX)-022 1.116 0.054 0.052 AS5861R(XX)-022 0.998 0.054 0.053 AS5861P(XX)-023 1.178 0.054 0.052 AS5861R(XX)-023 1.060 0.054 0.053 AS5861P(XX)-024 1.241 0.054 0.052 AS5861R(XX)-024 1.123 0.054 0.053 AS5861P(XX)-025

24、1.303 0.054 0.052 AS5861R(XX)-025 1.185 0.054 0.053 AS5861P(XX)-026 1.366 0.054 0.052 AS5861R(XX)-026 1.248 0.054 0.053 AS5861P(XX)-027 1.428 0.054 0.052 AS5861R(XX)-027 1.310 0.054 0.053 AS5861P(XX)-028 1.491 0.054 0.052 AS5861R(XX)-028 1.373 0.054 0.053 SAE INTERNATIONAL AS5861A Page 4 of 17 Table

25、 1A - AS5861 back up ring dimensions (in inches) (continued) Male (Piston) Applications Female (Rod) Applications Part No. OD 0.001 T 0.002 W 0.001 Part No. ID 0.001 T 0.002 W 0.001 AS5861P(XX)-104 0.286 0.058 0.081 AS5861R(XX)-104 0.123 0.058 0.081 AS5861P(XX)-105 0.317 0.058 0.081 AS5861R(XX)-105

26、0.154 0.058 0.081 AS5861P(XX)-106 0.349 0.058 0.081 AS5861R(XX)-106 0.185 0.058 0.081 AS5861P(XX)-107 0.382 0.058 0.081 AS5861R(XX)-107 0.217 0.058 0.081 AS5861P(XX)-108 0.414 0.058 0.081 AS5861R(XX)-108 0.248 0.058 0.081 AS5861P(XX)-109 0.477 0.058 0.081 AS5861R(XX)-109 0.310 0.058 0.081 AS5861P(XX

27、)-110 0.541 0.058 0.081 AS5861R(XX)-110 0.373 0.058 0.081 AS5861P(XX)-111 0.604 0.058 0.081 AS5861R(XX)-111 0.435 0.058 0.081 AS5861P(XX)-112 0.668 0.058 0.081 AS5861R(XX)-112 0.498 0.058 0.081 AS5861P(XX)-113 0.734 0.058 0.081 AS5861R(XX)-113 0.560 0.058 0.081 AS5861P(XX)-114 0.800 0.058 0.081 AS58

28、61R(XX)-114 0.623 0.058 0.081 AS5861P(XX)-115 0.863 0.058 0.081 AS5861R(XX)-115 0.685 0.058 0.081 AS5861P(XX)-116 0.925 0.058 0.081 AS5861R(XX)-116 0.748 0.058 0.081 AS5861P(XX)-117 0.991 0.058 0.081 AS5861R(XX)-117 0.810 0.058 0.081 AS5861P(XX)-118 1.053 0.058 0.081 AS5861R(XX)-118 0.873 0.058 0.08

29、1 AS5861P(XX)-119 1.116 0.058 0.081 AS5861R(XX)-119 0.935 0.058 0.081 OD ID 0.002 0.002AS5861P(XX)-120 1.178 0.058 0.081 AS5861R(XX)-120 0.998 0.058 0.081 AS5861P(XX)-121 1.241 0.058 0.081 AS5861R(XX)-121 1.060 0.058 0.081 AS5861P(XX)-122 1.303 0.058 0.081 AS5861R(XX)-122 1.123 0.058 0.081 AS5861P(X

30、X)-123 1.366 0.058 0.081 AS5861R(XX)-123 1.185 0.058 0.081 AS5861P(XX)-124 1.428 0.058 0.081 AS5861R(XX)-124 1.248 0.058 0.081 AS5861P(XX)-125 1.491 0.058 0.081 AS5861R(XX)-125 1.310 0.058 0.081 AS5861P(XX)-126 1.553 0.058 0.081 AS5861R(XX)-126 1.373 0.058 0.081 AS5861P(XX)-127 1.616 0.058 0.081 AS5

31、861R(XX)-127 1.435 0.058 0.081 AS5861P(XX)-128 1.678 0.058 0.081 AS5861R(XX)-128 1.498 0.058 0.081 AS5861P(XX)-129 1.741 0.058 0.081 AS5861R(XX)-129 1.560 0.058 0.081 AS5861P(XX)-130 1.805 0.058 0.081 AS5861R(XX)-130 1.623 0.058 0.081 AS5861P(XX)-131 1.867 0.058 0.081 AS5861R(XX)-131 1.685 0.058 0.0

32、81 AS5861P(XX)-132 1.930 0.058 0.081 AS5861R(XX)-132 1.748 0.058 0.081 AS5861P(XX)-133 1.992 0.058 0.081 AS5861R(XX)-133 1.810 0.058 0.081 AS5861P(XX)-134 2.055 0.058 0.081 AS5861R(XX)-134 1.873 0.058 0.081 SAE INTERNATIONAL AS5861A Page 5 of 17 Table 1A - AS5861 back up ring dimensions (in inches)

33、(continued) Male (Piston) Applications Female (Rod) Applications Part No. OD 0.002 T 0.002 W 0.001 Part No. ID 0.002 T 0.002 W 0.001 AS5861P(XX)-135 2.118 0.058 0.081 AS5861R(XX)-135 1.936 0.058 0.081 AS5861P(XX)-136 2.180 0.058 0.081 AS5861R(XX)-136 1.998 0.058 0.081 AS5861P(XX)-137 2.243 0.058 0.0

34、81 AS5861R(XX)-137 2.061 0.058 0.081 AS5861P(XX)-138 2.305 0.058 0.081 AS5861R(XX)-138 2.123 0.058 0.081 AS5861P(XX)-139 2.368 0.058 0.081 AS5861R(XX)-139 2.186 0.058 0.081 AS5861P(XX)-140 2.430 0.058 0.081 AS5861R(XX)-140 2.248 0.058 0.081 AS5861P(XX)-141 2.493 0.058 0.081 AS5861R(XX)-141 2.311 0.0

35、58 0.081 AS5861P(XX)-142 2.555 0.058 0.081 AS5861R(XX)-142 2.373 0.058 0.081 AS5861P(XX)-143 2.618 0.058 0.081 AS5861R(XX)-143 2.436 0.058 0.081 AS5861P(XX)-144 2.680 0.058 0.081 AS5861R(XX)-144 2.498 0.058 0.081 AS5861P(XX)-145 2.743 0.058 0.081 AS5861R(XX)-145 2.561 0.058 0.081 AS5861P(XX)-146 2.8

36、05 0.058 0.081 AS5861R(XX)-146 2.623 0.058 0.081 AS5861P(XX)-147 2.868 0.058 0.081 AS5861R(XX)-147 2.686 0.058 0.081 AS5861P(XX)-148 2.930 0.058 0.081 AS5861R(XX)-148 2.748 0.058 0.081 AS5861P(XX)-149 2.993 0.058 0.081 AS5861R(XX)-149 2.811 0.058 0.081 OD ID 0.001 0.001 AS5861P(XX)-210 0.991 0.062 0

37、.111 AS5861R(XX)-210 0.748 0.062 0.112 AS5861P(XX)-211 1.053 0.062 0.111 AS5861R(XX)-211 0.810 0.062 0.112 AS5861P(XX)-212 1.116 0.062 0.111 AS5861R(XX)-212 0.873 0.062 0.112 AS5861P(XX)-213 1.178 0.062 0.111 AS5861R(XX)-213 0.935 0.062 0.112 OD ID 0.002 0.002 AS5861P(XX)-214 1.241 0.062 0.111 AS586

38、1R(XX)-214 0.998 0.062 0.112 AS5861P(XX)-215 1.303 0.062 0.111 AS5861R(XX)-215 1.060 0.062 0.112 AS5861P(XX)-216 1.366 0.062 0.111 AS5861R(XX)-216 1.123 0.062 0.112 AS5861P(XX)-217 1.428 0.062 0.111 AS5861R(XX)-217 1.185 0.062 0.112 AS5861P(XX)-218 1.491 0.062 0.111 AS5861R(XX)-218 1.248 0.062 0.112

39、 AS5861P(XX)-219 1.553 0.062 0.111 AS5861R(XX)-219 1.310 0.062 0.112 AS5861P(XX)-220 1.616 0.062 0.111 AS5861R(XX)-220 1.373 0.062 0.112 AS5861P(XX)-221 1.678 0.062 0.111 AS5861R(XX)-221 1.435 0.062 0.112 AS5861P(XX)-222 1.741 0.062 0.111 AS5861R(XX)-222 1.498 0.062 0.112 AS5861P(XX)-223 1.867 0.062

40、 0.111 AS5861R(XX)-223 1.623 0.062 0.112 SAE INTERNATIONAL AS5861A Page 6 of 17 Table 1A - AS5861 back up ring dimensions (in inches) (continued) Male (Piston) Applications Female (Rod) Applications Part No. OD 0.002 T 0.002 W 0.001 Part No. ID 0.002 T 0.002 W 0.001 AS5861P(XX)-224 1.992 0.062 0.111

41、 AS5861R(XX)-224 1.748 0.062 0.112 AS5861P(XX)-225 2.118 0.062 0.111 AS5861R(XX)-225 1.873 0.062 0.112 AS5861P(XX)-226 2.243 0.062 0.111 AS5861R(XX)-226 1.998 0.062 0.112 AS5861P(XX)-227 2.368 0.062 0.111 AS5861R(XX)-227 2.123 0.062 0.112 AS5861P(XX)-228 2.493 0.062 0.111 AS5861R(XX)-228 2.248 0.062

42、 0.112 AS5861P(XX)-229 2.618 0.062 0.111 AS5861R(XX)-229 2.373 0.062 0.112 AS5861P(XX)-230 2.743 0.062 0.111 AS5861R(XX)-230 2.498 0.062 0.112 AS5861P(XX)-231 2.868 0.062 0.111 AS5861R(XX)-231 2.623 0.062 0.112 AS5861P(XX)-232 2.993 0.062 0.111 AS5861R(XX)-232 2.748 0.062 0.112 AS5861P(XX)-233 3.118

43、 0.062 0.111 AS5861R(XX)-233 2.873 0.062 0.112 AS5861P(XX)-234 3.243 0.062 0.111 AS5861R(XX)-234 2.997 0.062 0.112 AS5861P(XX)-235 3.368 0.062 0.111 AS5861R(XX)-235 3.122 0.062 0.112 AS5861P(XX)-236 3.493 0.062 0.111 AS5861R(XX)-236 3.247 0.062 0.112 AS5861P(XX)-237 3.618 0.062 0.111 AS5861R(XX)-237

44、 3.372 0.062 0.112 AS5861P(XX)-238 3.743 0.062 0.111 AS5861R(XX)-238 3.497 0.062 0.112 AS5861P(XX)-239 3.868 0.062 0.111 AS5861R(XX)-239 3.622 0.062 0.112 AS5861P(XX)-240 3.993 0.062 0.111 AS5861R(XX)-240 3.747 0.062 0.112 AS5861P(XX)-241 4.118 0.062 0.111 AS5861R(XX)-241 3.872 0.062 0.112 AS5861P(X

45、X)-242 4.243 0.062 0.111 AS5861R(XX)-242 3.997 0.062 0.112 AS5861P(XX)-243 4.368 0.062 0.111 AS5861R(XX)-243 4.122 0.062 0.112 AS5861P(XX)-244 4.493 0.062 0.111 AS5861R(XX)-244 4.247 0.062 0.112 AS5861P(XX)-245 4.618 0.062 0.111 AS5861R(XX)-245 4.372 0.062 0.112 AS5861P(XX)-246 4.743 0.062 0.111 AS5

46、861R(XX)-246 4.497 0.062 0.112 AS5861P(XX)-247 4.868 0.062 0.111 AS5861R(XX)-247 4.622 0.062 0.112 AS5861P(XX)-325 1.867 0.088 0.171 AS5861R(XX)-325 1.498 0.088 0.173 AS5861P(XX)-326 1.992 0.088 0.171 AS5861R(XX)-326 1.623 0.088 0.173 AS5861P(XX)-327 2.118 0.088 0.171 AS5861R(XX)-327 1.748 0.088 0.1

47、73 AS5861P(XX)-328 2.243 0.088 0.171 AS5861R(XX)-328 1.873 0.088 0.173 AS5861P(XX)-329 2.368 0.088 0.171 AS5861R(XX)-329 1.998 0.088 0.173 SAE INTERNATIONAL AS5861A Page 7 of 17 Table 1A - AS5861 back up ring dimensions (in inches) (continued) Male (Piston) Applications Female (Rod) Applications Par

48、t No. OD 0.002 T 0.002 W 0.001 Part No. ID 0.002 T 0.002 W 0.001 AS5861P(XX)-330 2.493 0.088 0.171 AS5861R(XX)-330 2.123 0.088 0.173 AS5861P(XX)-331 2.618 0.088 0.171 AS5861R(XX)-331 2.248 0.088 0.173 AS5861P(XX)-332 2.743 0.088 0.171 AS5861R(XX)-332 2.373 0.088 0.173 AS5861P(XX)-333 2.868 0.088 0.1

49、71 AS5861R(XX)-333 2.498 0.088 0.173 AS5861P(XX)-334 2.993 0.088 0.171 AS5861R(XX)-334 2.623 0.088 0.173 AS5861P(XX)-335 3.118 0.088 0.171 AS5861R(XX)-335 2.748 0.088 0.173 AS5861P(XX)-336 3.243 0.088 0.171 AS5861R(XX)-336 2.873 0.088 0.173 AS5861P(XX)-337 3.368 0.088 0.171 AS5861R(XX)-337 2.997 0.088 0.173 AS5861P(XX)-338 3.493 0.088 0.171 AS5861R(XX)-338 3.122 0.088 0.173 AS5861P(XX)-339 3

下载提示：本站仅提供存储空间/不修改/不编辑

1.请仔细阅读文档，确保文档完整性，对于不预览、不比对内容而直接下载带来的问题本站不予受理。
2.下载的文档，不会出现我们的网址水印。
3、该文档所得收入（下载+内容+预览）归上传者、原创作者；如果您是本文档原作者，请点此认领！既往收益都归您。

同意并开始全文预览

文档包含非法信息？点此举报后获取现金奖励！

文档加载中……请稍候！
如果长时间未打开，您也可以点击刷新试试。

下载文档到电脑，查找使用更方便

10000 积分 0人已下载

下载	加入VIP,交流精品资源

版权申诉 word格式文档无特别注明外均可编辑修改；预览文档经过压缩，下载后原文更清晰！ 立即下载

配套讲稿：: 如PPT文件的首页显示word图标，表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
特殊限制：: 部分文档作品中含有的国旗、国徽等图片，仅作为作品整体效果示例展示，禁止商用。设计者仅对作品中独创性部分享有著作权。
关键词：: SAEAS5861A2015RETAINERSBACKUPRINGSHYDRAULICANDPNEUMATICPOLYTETRAFLUOROETHYLENERESINSOLIDSTATICGLANDPDF

麦多课文档分享所有资源均是用户自行上传分享，仅供网友学习交流，未经上传用户书面授权，请勿作他用。

关于本文

本文标题：SAE AS 5861A-2015 Retainers (Back-Up Rings) Hydraulic and Pneumatic Polytetrafluoroethylene Resin Solid Static Gland.pdf
链接地址：http://www.mydoc123.com/p-1024975.html