SAE AS 4675B-2017 TEE ASSEMBLY RETAINED NUT ON SIDE SHORT FLARELESS.pdf

《SAE AS 4675B-2017 TEE ASSEMBLY RETAINED NUT ON SIDE SHORT FLARELESS.pdf》由会员分享，可在线阅读，更多相关《SAE AS 4675B-2017 TEE ASSEMBLY RETAINED NUT ON SIDE SHORT FLARELESS.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD TEE ASSEMBLY, RETAINED NUT ON SIDE, SHORT FLARELESS AS4675Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording

2、, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED1992-07REAFFIRMED 2004-07REVISED2017-09THIRD A

3、NGLE PROJECTION CUSTODIAN: G-3/G-3B REV.B FEDERAL SUPPLY CLASS 4730 AS4675 SHEET 1 OF 4 REV. B PROCUREMENT SPECIFICATION: AS18280 /4/ SAE Technical Standards Board Rules provide that: “This report is published by SAEtoadvance thestate of technicaland engineering sciences. The useof this report is en

4、tirely voluntary, and its applicability andsuitability for any particularuse, includingany patent infringement arisingtherefrom,is the sole responsibility of theuser.” SAE reviews eachtechnical reportatleast every fiveyears at whichtime it may be revised, reaffirmed, stabilized, or cancelled. SAE in

5、vites your written comments and suggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS4675B RATIONALE ADDED CONDUCTIVE HIGH PURITY ALUMINUM COATING FOR ALUMINUM ALLOY FITTINGS. . FIGURE 1 - TEE ASSEMBLY FIGURE 2 - INSTALLATION, RETAIN

6、ED NUT AND RETAINING WIRE AEROSPACE STANDARD AS4675 SHEET 2 OF 4 REV. B TEE ASSEMBLY, RETAINED NUT ON SIDE, SHORT FLARELESS TABLE 1 - DIMENSIONS AND WEIGHTS BASIC NO. AS4675 /10/ /18/ SIZE CODE (NOMINAL TUBE SIZE) T THREAD PER AS8879 CLASS 3A AND CLASS 3B A B C D H J +.005 -.020 LB/EA APPROX REF ALU

7、M LB/EA APPROX REF CRES LB/EA APPROX REF TI 20 1.250 1.5625-12UNJ 1.678 1.603 .155 .517 .124 1.375 .395 1.146 .666 24 1.500 1.8125-12UNJ 1.803 1.756 .160 .614 .156 1.688 .570 1.651 .954 NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIAL

8、S IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. /1/ MATERIAL: a. CODE LETTER T: (1) BODY: TYPE 6AL-4V TITANIUM ALLOY PER AMS4928 (2) NUT: CODE LETTER T OF AS4702 REFERENCE (TYPE 6AL-4V TITANIUM ALLOY) (3) WIRE: PER AS4701 REFERENCE (CLASS 302 OR 305 CORROSION RESISTANT STEEL) b. CODE LETTER V: (1)

9、BODY: TYPE 15-5PH CORROSION RESISTANT STEEL PER AMS5659 (2) NUT: CODE LETTER V OF AS4702 REFERENCE (TYPE 15-5PH CORROSION RESISTANT STEEL) (3) WIRE: PER AS4701 REFERENCE (CLASS 302 OR 305 CORROSION RESISTANT STEEL) c. CODE LETTER W: (1) BODY: TYPE 7075-T73 ALUMINUM ALLOY FORGING PER AMS4141 OR TYPE

10、7075-T7351 ALUMINUM ALLOY BAR PER AMS4124 (2) NUT: CODE LETTER W OF AS4702 REFERENCE (TYPE 7075-T7351 ALUMINUM ALLOY) (3) WIRE: PER AS4701 REFERENCE (CLASS 302 OR 305 CORROSION RESISTANT STEEL) 2. HEAT TREATMENT: a. MATERIAL CODE LETTER T: (1) BODY, NUT, AND WIRE: NONE b. MATERIAL CODE LETTER V: (1)

11、 BODY: HEAT TREAT TO CONDITION H-1075 PER AMS2759/3 (2) NUT: MATERIAL CODE LETTER V OF AS4702 REFERENCE (HEAT TREAT TO CONDITION H-1075) (3) WIRE: NONE c. MATERIAL CODE LETTER W: (1) BODY, NUT, AND WIRE: NONE AEROSPACE STANDARD AS4675 SHEET 3 OF 4 REV. B TEE ASSEMBLY, RETAINED NUT ON SIDE, SHORT FLA

12、RELESS /3/ FINISH: a. MATERIAL CODE LETTER T: (1) BODY: FLUORIDE PHOSPHATE CONVERSION COAT PER AMS2486. (2) NUT: CODE LETTER T OF AS4702 REFERENCE (FLUORIDE PHOSPHATE CONVERSION COAT AND COAT WITH DRY LUBRICANT ON ID) (3) WIRE: PER AS4701 REFERENCE (PASSIVATE AND COAT WITH DRY LUBRICANT) b. MATERIAL

13、 CODE LETTER V: (1) BODY: (a) V CODE PARTS TO BE PASSIVATED ONLY WILL HAVE NO FINISH CODE LETTER AFTER THE PART NUMBER. THE FINISH WILL BE: PASSIVATE PER AMS2700 TYPE 2 OR 8. (b) V CODE PARTS TO BE CADMIUM PLATED ONLY WILL HAVE THE FINISH CODE LETTER “P” AFTER THE SIZE CODE IN THE PART NUMBER. THE F

14、INISH WILL BE: CADMIUM PLATE PER AMS-QQ-P-416, TYPE II, CLASS 2. (2) NUT: CODE LETTER V OF AS4702 REFERENCE (a) NO FINISH CODE LETTER AT END OF PART NUMBER: PASSIVATE AND COAT WITH DRY FILM LUBRICANT ON ID (b) FINISH CODE LETTER P AT END OF PART NUMBER: CADMIUM PLATE (3) WIRE: PER AS4701 REFERENCE (

15、PASSIVATE AND COAT WITH DRY FILM LUBRICANT) c. MATERIAL CODE LETTER W: (1) BODY: (a) W CODE PARTS TO BE ANODIZED ONLY WILL HAVE NO FINISH CODE LETTER AFTER THE SIZE CODE IN THE PART NUMBER. THE FINISH WILL BE ANODIZE PER AMS2472 OR PER MIL-A-8625, TYPE II, CLASS 2 DYED BROWN, SIMILAR TO COLOR 10080

16、OF AMS-STD-595. (b) W CODE PARTS TO BE COATED WITH HIGH PURITY ALUMINUM ONLY WILL HAVE THE FINISH CODE LETTER “V” AFTER THE SIZE CODE IN THE PART NUMBER. SEE PROCUREMENT SPECIFICATION FOR REQUIREMENTS. (2) NUT: CODE LETTER W OF AS4702 REFERENCE (ANODIZE DYED BROWN AND COAT WITH DRY FILM LUBRICANT) (

17、3) WIRE: PER AS4701 REFERENCE. (PASSIVATE AND COAT WITH DRY FILM LUBRICANT). /4/ PROCUREMENT SPECIFICATION: AS18280 EXCEPT AS SPECIFIED ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER AS LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUA

18、LIFIED PRODUCTS LIST (QPL) PRI-QPL-AS18280 FOR THIS STANDARD. SEE www.eAuditN FOR CURRENT QPL ONLINE. /5/ IDENTIFICATION AT LOCATION SHOWN: MARK PER AS478 CLASS C OR D OR METHOD 7A3, 15A3, OR 15B. MANUFACTURERS NAME, TRADEMARK OR CAGE CODE, BASIC PART NUMBER AND MATERIAL CODE LETTER. 6. INTENDED USE

19、: THIS PART IS DESIGNED FOR USE IN TUBE CONNECTION SYSTEMS WITH NOMINAL OPERATING PRESSURES AS FOLLOWS: a. SIZES -20 AND -24 TITANIUM ALLOY AND CORROSION RESISTANT STEEL AT 3000 psi b. SIZES -20 AND -24 ALUMINUM ALLOY AT 600 psi. 7. WHEN MACHINED FROM BAR OR OVERSIZED FORGINGS THE CENTER BODY SECTIO

20、N SHALL CONFORM TO AS1376, TABLE 10 /8/ RADIUS APPLICABLE FOR TITANIUM PARTS ONLY. /9/ ASSEMBLE AS4702 RETAINED NUT TO FITTING BODY WITH AS4701 RETAINING WIRE AS SHOWN IN FIGURE 2. THE NUT SHALL BE FREE TO ROTATE AFTER ASSEMBLY. /10/ THIS IS A NONREDUCER FITTING. ALL PORTS OF ANY GIVEN PART WILL BE

21、THE SAME SIZE. FOR REDUCERS USE AS4692. AEROSPACE STANDARD AS4675 SHEET 4 OF 4 REV. B TEE ASSEMBLY, RETAINED NUT ON SIDE, SHORT FLARELESS /10/PMA TE RI AL CO DE LE TTE R /1/FI NI SH CO DE LE TTE R / 3/ /11 /SI ZE CO DE , T UB E S I ZE OF PO RT #3 I N . 06 2 I NCR EM EN TSSI ZE CO DE , T UB E S I ZE

22、OF PO RT #1 I N . 06 2 I NCR EM EN TSSI ZE CO DE , T UB E S I ZE OF PO RT #2 I N . 06 2 I NCR EM EN TSBA SI C P AR T N UM BE RAS4675 V 20 20 20/11/ FINISH CODE LETTER “P” SHALL BE PLACED AFTER SIZE CODES ONLY FOR MATERIAL CODE “V” PARTS THAT ARE TO BE CADMIUM PLATED. FINISH CODE LETTER “V” SHALL BE

23、PLACED AFTER SIZE CODES ONLY FOR MATERIAL CODE “W” PARTS THAT ARE TO BE COATED WITH HIGH PURITY ALUMINUM TO PROVIDE LOW ELECTRICAL CONTACT RESISTANCE. NO OTHER LETTERS ARE TO FOLLOW THE SIZE CODES. 12. REVISION INDICATOR: A CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE US

24、ER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUB

25、LICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. 13. INTERPRETATION OF DRAWING PER AS4296. 14. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 MICROINCHES Ra. FORGED SURFACES MAY BE 250 MICROINCHES Ra. 15. BREAK EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED. 16. DIMENSIONING AND TOLERANCING: ANSI Y14.5M-1982 17. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .010, ANGULAR DIMENSIONS 5 DEGREES. /18/ EXAMPLE OF PART NUMBER: