SAE AS 4590-2001 HOSE ASSEMBLY PTFE PARA-ARAMID REINFORCED STANDARD DUTY 4000 PSI 275 F TITANIUM FITTINGS BEAM SEAL 45 TO 90 《45对90角定向密封的钛配件、4000psi、275F标准型对位芳族增强聚四氟乙烯软管组件》.pdf

《SAE AS 4590-2001 HOSE ASSEMBLY PTFE PARA-ARAMID REINFORCED STANDARD DUTY 4000 PSI 275 F TITANIUM FITTINGS BEAM SEAL 45 TO 90 《45对90角定向密封的钛配件、4000psi、275F标准型对位芳族增强聚四氟乙烯软管组件》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 4590-2001 HOSE ASSEMBLY PTFE PARA-ARAMID REINFORCED STANDARD DUTY 4000 PSI 275 F TITANIUM FITTINGS BEAM SEAL 45 TO 90 《45对90角定向密封的钛配件、4000psi、275F标准型对位芳族增强聚四氟乙烯软管组件》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD HOSE ASSEMBLY, PTFE, PARA-ARAMID REINFORCED, STANDARD DUTY, 4000 PSI, 275 F, TITANIUM FITTINGS, BEAM SEAL, 45 TO 90 AS4590Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form

2、or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/

3、www.sae.org ISSUED 2001-03REAFFIRMED2015-04THIRD ANGLE PROJECTION CUSTODIAN: G-3/G-3D FEDERAL SUPPLY CLASS 4720AS4590 SHEET 1 OF 6 PROCUREMENT SPECIFICATION: AS1975 /2/SAE Technical Standards Board Rules provide that: “This report ispublished by SAE toadvance thestate of technicalandengineering scie

4、nces. Theuse ofthisreport is entirelyvoluntary, andits applicability and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabi

5、lized, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS4590 RATIONALE AS4590 HAS BEEN REAFFIRMED TO COMPLY WITH THE SAE FIVE-YEAR REVIEW POLICY. FIGURE 1 - ENLARGED V

6、IEW - 45 END FITTINGFIGURE 2 - ASSEMBLY ORIENTATIONAEROSPACE STANDARD AS4590 SHEET 2 OF 6 HOSE ASSEMBLY, PTFE, PARA-ARAMID REINFORCED, STANDARD DUTY, 4000 PSI, 275 F, TITANIUM FITTINGS, BEAM SEAL, 45 TO 90 FIGURE 3 - ENLARGED VIEW - 90 END FITTINGAEROSPACE STANDARD AS4590 SHEET 3 OF 6 HOSE ASSEMBLY,

7、 PTFE, PARA-ARAMID REINFORCED, STANDARD DUTY, 4000 PSI, 275 F, TITANIUM FITTINGS, BEAM SEAL, 45 TO 90 TABLE 1 - ASSEMBLY DIMENSIONSHOSEASSEMBLYNO. & SIZECODE /21/HOSESIZE(REF)THREAD TPER AS8879(REF)HOSEID MINA1 MAXA2 MAXC HEX(REF)D /8/DIA MAXWITHOUTSLEEVINGE1 MINE1 MAXE2 MINE2 MAXSPHERICALBALL SIZEF

8、ORDETERMININGMINIMUMHOSEASSEMBLY ID /7/INAS4590E.250.4375-24UNJS-3B.2122.1051.880.56.69.310.435.576.701.115AS4590G.375.5625-20UNJS-3B.2982.3802.180.69.80.310.435.610.735.204AS4590H.500.7188-20UNJS-3B.3912.6352.530.88.97.314.439.693.818.289AS4590J.625.8438-18UNJS-3B.4853.5003.3751.001.15.357.482.834.

9、959.349AS4590K.7501.000-16UNJ-3B.6023.8903.9401.251.38.385.510.9881.113.434AS4590M1.0001.250-14UNJS-3B.8524.4054.4851.501.66.480.6051.1671.292.646TABLE 2 - HOSE OR SLEEVE OUTSIDE DIAMETERSLEEVECODE /22/SLEEVE MATERIALTEMPLIMITFTOLERANCEHOSESIZE/10/.250HOSESIZE/10/.375HOSESIZE/10/.500HOSESIZE/10/.625

10、HOSESIZE/10/.750HOSESIZE/10/1.000-(-) INDICATES BRAIDED HOSEONLY PER AS1975275MAXMIN.465.405.555.495.715 .655.920 .8501.075 .9951.3651.285AFIRESLEEVE (AS1072 SIL - FG)(5 min) /11/ /12/275MAXMIN.840.658.970.7881.150 .9681.3801.1981.5901.3181.7501.568BFIRESLEEVE INTEGRAL SILICONE(5 min) /13/275MAXMINC

11、PROTECTIVE SLEEVESHRINK-ON (POLYOLEFIN AS1073CODE B)275MAXMIN.520.450.620.550.795 .7251.000 .9201.1701.0601.4601.350AEROSPACE STANDARD AS4590 SHEET 4 OF 6 HOSE ASSEMBLY, PTFE, PARA-ARAMID REINFORCED, STANDARD DUTY, 4000 PSI, 275 F, TITANIUM FITTINGS, BEAM SEAL, 45 TO 90 NOTES:1. MATERIALS:a. HOSE AN

12、D FITTINGS - PER AS1975b. SLEEVES - SEE APPLICABLE STANDARDS, TABLE 2/2/ THIS PRODUCT SHALL BE QUALIFIED IN ACCORDANCE WITH PROCUREMENT SPECIFICATION AS1975 CLASS 4000. USERS OF THIS STANDARD SHALL PROCURE THIS PRODUCT FROM ACCREDITED MANUFACTURER(S), OR THEIR ACCREDITED DISTRIBUTOR(S), AS LISTED IN

13、 THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST PRI-QPL-AS1975 CLASS 4000 FOR THIS STANDARD. CHANGE-OVER FROM USER-QPL TO PRI-QPL SHALL BE IN ACCORDANCE WITH AS1975 REVISION C OR HIGHER AND BE COMPLETED WITHIN SIX MONTHS FROM THE DATE OF ISSUE OF THIS STANDARD.3. CONSTRUCTION AND PER

14、FORMANCE PER AS1975 CLASS 4000. FITTINGS SHALL BE PERMANENTLY ATTACHED TO THE HOSE.4. OPERATING CHARACTERISTICS PER AS1975./5/ MARKING: MARKING SHALL BE PER AS1975 ON A STAINLESS STEEL BAND NOT OVER 1.0 in WIDE OR ON THE COLLAR. THE CHARACTERS SHALL BE A MINIMUM OF .06 in HIGH. THE BAND SHALL BE SO

15、DESIGNED AS TO REMAIN TIGHT ON THE HOSE TO PREVENT RELATIVE MOVEMENT AND RESULTANT CHAFING. IT SHALL BE OF SUFFICIENT STRENGTH TO PREVENT REMOVAL BY HAND. HOSE ASSEMBLY DATE AND “PT” SYMBOL SHALL BE PERMANENTLY MARKED ON THE BAND OR ON AN END FITTING OR A FIRESLEEVE CLAMP. MARKING BAND SHALL BE COVE

16、RED WITH TRANSPARENT POLYOLEFIN SHRINK SLEEVE PER AS1073 CODE A.TABLE 3 - ASSEMBLY LENGTH TOLERANCESHOSE ASSEMBLY LENGTH TOLERANCEUNDER 18 in .125 in18 TO 36 in EXCLUSIVE .250 in36 TO 50 in EXCLUSIVE .500 in50 in AND OVER 1%TABLE 4 - HOSE AND FITTING WEIGHTSHOSEOR SLEEVECODE /22/HOSE OR TYPESLEEVE U

17、NITSHOSESIZE.250HOSESIZE.375HOSESIZE.500HOSESIZE.625HOSESIZE.750HOSESIZE1.000- BRAIDED HOSE ONLY PER AS1975 LB/IN (MAX) .006 .008 .012 .020 .025 .040A FIRESLEEVE AS1072 (5 minPER AS1055) /15/LB/IN .012 .017 .018 .028 .030 .037B FIRESLEEVE INTEGRAL WITHHOSE (5 min PER AS1055) /15/LB/INC PROTECTIVE SL

18、EEVE SHRINK-ON(POLYOLEFIN AS1073, CODE B)LB/IN .001 .001 .001 .002 .002 .003NONE FIRESLEEVE CLAMP LB/EA (REF) .020 .020 .021 .021 .025 .025NONE FITTING END (45) TITANIUM /16/ LB/EA (REF) .060 .115 .188 .265 .470 .575NONE FITTING END (90) TITANIUM /16/ LB/EA (REF) .067 .121 .206 .290 .490 .627AEROSPA

19、CE STANDARD AS4590 SHEET 5 OF 6 HOSE ASSEMBLY, PTFE, PARA-ARAMID REINFORCED, STANDARD DUTY, 4000 PSI, 275 F, TITANIUM FITTINGS, BEAM SEAL, 45 TO 90 /6/ LENGTH “L” IS A THREE DIGIT NUMBER OF WHICH THE FIRST TWO DIGITS DESCRIBE THE HOSE ASSEMBLY LENGTH IN WHOLE INCHES, AND THE THIRD DIGIT, THE FRACTIO

20、NS OF AN INCH IN EIGHTHS. LENGTH “L” IS MEASURED FROM THE OUTER CORNER OF THE SEALING SURFACE TO OUTER CORNER OF SEALING SURFACE AS SHOWN IN FIGURE 1. FOR LENGTH TOLERANCES SEE TABLE 3./7/ A TRUE CIRCULAR CROSS SECTION IS NOT REQUIRED THROUGH THE FITTING ID. HOWEVER, THE APPLICABLE MINIMUM BALL DIAM

21、ETER LISTED IN TABLE 1 MUST BE CAPABLE OF PASSING THROUGH THE HOSE ASSEMBLY./8/ DISTANCE ACROSS CORNERS OF THE HEX MAY EXCEED THIS DIMENSION./9/ STANDARD COUPLING NUTS SHALL MATE WITH MIL-F-85421/1 OR AS4207 FITTING ENDS. NONSTANDARD COUPLING NUTS MAY BE USED PROVIDED THEY ARE FUNCTIONALLY EQUIVALEN

22、T AND PROVIDED THEY CANNOT BE REMOVED FROM THE FITTING. NUTS SHALL MEET THE TORQUE TEST REQUIREMENTS PER AS1975./10/ DIAMETERS ARE LISTED FOR CLAMP SELECTION. TUBULAR SLEEVES MAY NOT BE A PERFECT ROUND AND SHALL BE MEASURED WITH A DIAMETER TAPE RULE (OFTEN REFERRED TO AS A PI-TAPE)./11/ THE TABLE 2

23、SLEEVE DIAMETERS FOR AS1072 SLEEVES APPLY WHEN THE SLEEVE IS COMPRESSED OR CLAMPED TO CONTACT THE HOSE. IN THIS CASE A WRINKLE MAY OCCUR OVER APPROXIMATELY 10% OF THE SLEEVE CIRCUMFERENCE./12/ THE CUT ENDS OF THE FIRESLEEVE SHALL BE COATED WITH RTV SILICONE RUBBER PRIOR TO INSTALLATION TO PREVENT WI

24、CKING OF FLUIDS. THE FIRESLEEVE ENDS SHALL BE SECURED TO THE HOSE ASSEMBLY END FITTINGS WITH CORROSION RESISTANT STEEL BANDS. AFTER INSTALLATION, CRACKS OR VOIDS IN THE FIRESLEEVE WHICH EXPOSE FIBERGLASS SHALL BE COATED WITH RTV SILICONE RUBBER./13/ THE ENDS OF THE INTEGRAL FIRESLEEVE SHALL BE COVER

25、ED WITH SILICONE EXTENDING OVER THE END FITTING COLLAR.14. ADD “AS1055 TYPE IIb CLASS A-S/P” OR “AS150 TYPE XIII” TO IDENTIFICATION MARKING TO SHOW LEVEL OF COMPLIANCE, “FIRE RESISTANT” 275 F (5 min), WITH AS1055 OR AS150./15/ WHEN FIRESLEEVES ARE REQUIRED, WEIGHT LIMITS SHALL BE DEFINED BY THE PROC

26、URING ACTIVITY./16/ TITANIUM PARTS MAY BE REPLACED WITH STAINLESS STEEL IF MAXIMUM WEIGHT FOR FITTING IS NOT EXCEEDED AND THE STAINLESS STEEL COMPONENTS HAVE BEEN PREVIOUSLY QUALIFIED.17. DIMENSIONING AND TOLERANCING PER ASME Y14.5M-1994./18/ THE FITTING ORIENTATION DASH NUMBER IS A THREE DIGIT NUMB

27、ER DEFINING THE RELATIVE POSITION OF THE END FITTINGS IN 1 INCREMENTS (EXAMPLE 090 = 90). FITTING ORIENTATION SHALL BE MEASURED COUNTERCLOCKWISE FROM THE NEAREST END FITTING, WHICH SHALL BE IN THE RELATIVE 000 POSITION (SEE FIGURE 2). WHEN END FITTINGS ARE POINTED IN THE SAME DIRECTION, THIS DASH NU

28、MBER SHALL BE 000./19/ SAFETY WIRE HOLES LOCATION AND DIAMETER PER AS1043 CODED AS FOLLOWS:a. U = TWO HOLES 180 APARTb. W = THREE HOLES 120 APART20. THIS PART STANDARD TAKES PRECEDENCE IN CASES OF CONFLICT.21. THE SHRINK ON POLYOLEFIN SLEEVE SHALL COVER THE ENTIRE HOSE AND A MINIMUM OF 50% OF THE CO

29、LLARS ON BOTH ENDS OF THE ASSEMBLY.AEROSPACE STANDARD AS4590 SHEET 6 OF 6 HOSE ASSEMBLY, PTFE, PARA-ARAMID REINFORCED, STANDARD DUTY, 4000 PSI, 275 F, TITANIUM FITTINGS, BEAM SEAL, 45 TO 90 /22/ EXAMPLE OF PART NUMBER:23. THIS HOSE ASSEMBLY STANDARD IS SIMILAR TO AS4578 EXCEPT FOR PROCUREMENT PURPOSES. THIS PART STANDARD SHALL BE USED FOR ALL FUTURE PROCUREMENT OF CLASS 4000 HOSE ASSEMBLIES.