SAE AS 4227C-2017 FITTING ASSEMBLY ADAPTER INTERNAL THREAD BEAM SEAL TO INTEGRAL WELD RING.pdf

《SAE AS 4227C-2017 FITTING ASSEMBLY ADAPTER INTERNAL THREAD BEAM SEAL TO INTEGRAL WELD RING.pdf》由会员分享，可在线阅读，更多相关《SAE AS 4227C-2017 FITTING ASSEMBLY ADAPTER INTERNAL THREAD BEAM SEAL TO INTEGRAL WELD RING.pdf（5页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD FITTING ASSEMBLY, ADAPTER, INTERNAL THREAD, BEAM SEAL TO INTEGRAL WELD RING AS4227Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical,

2、 photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED1996-05REAFFIRMED 2007

3、-10REVISED2017-11THIRD ANGLE PROJECTION CUSTODIAN: G-3/G-3B REV.C FEDERAL SUPPLY CLASS 4730 AS4227 SHEET 1 OF 5 REV. C PROCUREMENT SPECIFICATION: AS85421 OR AS85720 /5/ SAE Technical Standards Board Rules provide that: “This report is published by SAEtoadvance thestate of technicaland engineering sc

4、iences. The useof this report is entirely voluntary, and its applicability andsuitability for any particularuse, includingany patent infringement arisingtherefrom,is the sole responsibility of theuser.” SAE reviews eachtechnical reportatleast every fiveyears at whichtime it may be revised, reaffirme

5、d, stabilized, or cancelled. SAE invites your written comments and suggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS4227C RATIONALE 1. REVISE NOTE /4/ TO REMOVE REQUIREMENT FOR DRY FILM LUBRICANT ON FEMALE BEAM SEAL END. FEMALE B

6、EAM SEAL END DOES NOT REQUIRE DRY FILM LUBRICANT. 2. CORRECT TYPO ON TABLE 1A CHANGING SIZE CODE 16-078 TO 16-089 AND TABLE 2A/2B CHANGING AS4229 TO AS4227. 3. REVISE NOTE /5/ TO CLARIFY PROCUREMENT SPECIFICATION AND APPLICABLE SIZE AND TUBE WALL CODES. FIGURE 1 - FITTING ASSEMBLY, ADAPTER I N T E G

7、 R A L A T T A C H M E N T A R E A .D E S IG N A T M A N U F A C T U R E R SO P T IO NI N T E G R A L A T T A C H M E N T A R E A .I N C LU D I N G T H E P O S IT IO N O FT H E N U T M A Y E X T E N D T O T H EP O R T # 2F IT T IN G E N D P E R A S 4 69 7F O R T U B E S I Z E , W A LLT H I C K N E S

8、 S R A N G E A N DE N D S T Y LE S P E C I F IE D(S T Y L E A S H O W N )L O C A T IO N O FI D E N T IF IC A T IO N /6 /NUTP O R T # 1F IT T IN G E N DP E R A S 4 20 9.3 00M INC/ 8/(T T H R E A D )/ 4/AA D A P T E R( D )/ 8/L IM IT A S S H O W NEM IN(H)AEROSPACE STANDARD AS4227 SHEET 2 OF 5 REV. C F

9、ITTING ASSEMBLY, ADAPTER, INTERNAL THREAD, BEAM SEAL TO INTEGRAL WELD RING TABLE 1 TABLE 1A - DIMENSIONS BASIC NO. AS4227 /14/ SIZE AND TUBE WALL CODES RANGE OF NOMINAL TUBE WALL FOR PORT #2 /7/ /14/ (NOMINAL TUBE SIZE) T THREAD PER AS8879 CLASS 3B PORT #2 STYLE /8/ A 03-018 .016-.018 .188 .3750-28

10、UNJS A .635 03-022 .019-.022 .188 .3750-28 UNJS A .635 04-022 .019-.022 .250 .4375-24 UNJS B .747 05-022 .019-.022 .312 .5000-24 UNJS B .675 05-028 .023-.028 .312 .5000-24 UNJS B .675 06-022 .019-.022 .375 .5625-20 UNJS B .781 06-028 .023-.028 .375 .5625-20 UNJS B .781 06-032 .029-.032 .375 .5625-20

11、 UNJS B .781 08-022 .019-.022 .500 .7188-20 UNJS B .788 08-043 .033-.043 .500 .7188-20 UNJS A .788 10-028 .023-.028 .625 .8438-18 UNJS B .857 10-043 .033-.043 .625 .8438-18 UNJS B .857 10-055 .044-.055 .625 .8438-18 UNJS A .857 12-028 .023-.028 .750 1.0000-16 UNJ B .898 12-055 .044-.055 .750 1.0000-

12、16 UNJ B .899 12-065 .056-.065 .750 1.0000-16 UNJ A .899 14-032 .029-.032 .875 1.1250-16 UNJ B .944 14-065 .056-.065 .875 1.1250-16 UNJ A .944 16-043 .033-.043 1.000 1.2500-14 UNJ B .997 16-078 .066-.078 1.000 1.2500-14 UNJS A .997 16-089 .079-.089 1.000 1.2500-14 UNJS A .997 20-055 .044-.055 1.250

13、1.5781-14 UNJS B 1.043 20-089 .079-.089 1.250 1.5781-14 UNJS A 1.043 24-055 .044-.055 1.500 1.8438-14 UNJS B 1.450 AEROSPACE STANDARD AS4227 SHEET 3 OF 5 REV. C FITTING ASSEMBLY, ADAPTER, INTERNAL THREAD, BEAM SEAL TO INTEGRAL WELD RING TABLE 1B - DIMENSIONS AND WEIGHTS BASIC NO. AS4227 /14/ SIZE AN

14、D TUBE WALL CODES C /8/ D /8/ E H RECOMMENDED MAXIMUM SYSTEM PRESSURE PSI /5/ /7/ APPROX MASS CRES LB/100 APPROX MASS TI LB/100 03-018 - .146 .568 .500 5000 2.18 1.24 03-022 - .138 .568 .500 5000 2.18 1.24 04-022 .184- .194 .200 .638 .562 5000 2.99 1.71 05-022 .232- .242 .262 .709 .625 4000 3.71 2.1

15、2 05-028 .232- .242 .250 .709 .625 5000 3.71 2.20 06-022 .297- .307 .325 .780 .688 3000 4.73 2.70 06-028 .297- .307 .313 .780 .688 4000 4.73 2.70 06-032 .297- .307 .305 .780 .688 5000 4.73 2.70 08-022 .398- .408 .450 .993 .875 2000 7.87 4.50 08-043 - .408 .993 .875 5000 7.87 4.50 10-028 .512- .523 .

16、563 1.120 1.000 2000 11.10 6.33 10-043 .512- .523 .533 1.120 1.000 4000 11.10 6.33 10-055 - .509 1.120 1.000 5000 11.10 6.33 12-028 .649- .660 .688 1.260 1.125 2000 13.40 7.66 12-055 - .634 1.260 1.125 4000 13.40 7.66 12-065 - .614 1.280 1.125 5000 13.40 7.66 14-032 .769- .780 .805 1.540 1.375 2000

17、22.30 12.70 14-065 - .739 1.540 1.375 4000 22.30 12.70 16-043 .862- .874 .908 1.650 1.500 2000 29.60 16.90 16-078 - .838 1.650 1.500 4000 29.60 16.90 16-089 - .816 1.500 1.500 5000 29.60 16.90 20-055 1.115-1.128 1.134 2.063 1.875 2000 45.80 26.20 20-089 - 1.066 2.063 1.875 4000 45.80 26.20 24-055 1.

18、324-1.337 1.384 2.338 2.125 2000 67.30 38.50 NOTES /1/ MATERIAL: a. CODE LETTER P - TYPE 17-4PH CORROSION RESISTANT STEEL PER AMS5643. b. CODE LETTER T - TYPE 6Al-4V TITANIUM ALLOY BAR PER AMS4965. c. CODE LETTER V - TYPE 15-5PH CORROSION RESISTANT STEEL PER AMS5659. d. CODE LETTER Y - TYPE 718 CORR

19、OSION AND HEAT RESISTANT NICKEL ALLOY PER AMS5663. 2. HEAT TREATMENT: a. MATERIAL CODE LETTER P - CONDITION H1075 PER AMS-H-6875 OR AMS2759/3. b. MATERIAL CODE LETTER T, Y - NONE. c. MATERIAL CODE LETTER V - CONDITION H1075 PER AMS-H-6875 OR AMS2759/3. 3. FINISH: a. MATERIAL CODE LETTER P - PASSIVAT

20、E PER AMS2700 TYPE 2 OR 8. b. MATERIAL CODE LETTER T, Y - NONE. c. MATERIAL CODE LETTER V - PASSIVATE PER AMS2700 TYPE 2 OR 8. AEROSPACE STANDARD AS4227 SHEET 4 OF 5 REV. C FITTING ASSEMBLY, ADAPTER, INTERNAL THREAD, BEAM SEAL TO INTEGRAL WELD RING /4/ DRY FILM LUBRICANT a. MATERIAL CODE LETTERS: P,

21、 V, T, (400 F MAXIMUM) USE LUBRICANT AS5272 TYPE I OR TYPE III. b. MATERIAL CODE LETTER Y, (1300 F MAXIMUM) USE LUBRICANT AS1701 CLASS IV. APPLY DRY FILM LUBRICANT TO THE THREADS OF THE NUT. MINOR OVER SPRAY ON THE OUTSIDE OF THE NUT IS PERMITTED. /5/ PROCUREMENT SPECIFICATION: AS85421 FOR MAXIMUM S

22、YSTEM PRESSURE 4000 PSI AND BELOW OR AS85720 FOR MAXIMUM SYSTEM PRESSURE ABOVE 4000 PSI, SEE TABLE 1B FOR APPLICABLE SIZE AND TUBE WALL CODES AND THE RECOMMENDED MAXIMUM SYSTEM PRESSURE. THESE PARTS SHALL BE QUALIFIED TO THE APPLICABLE REQUIREMENT OF PROCUREMENT SPECIFICATION AS A COMPLETE ASSEMBLY.

23、 THE WELDED FITTING END AND WELDED FITTING PARTS SHALL MEET THE PERFORMANCE REQUIREMENTS OF AS4510. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY THE ACCREDITED MANUFACTURER LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCT LIST (QPL) PRI-QPL-AS85421 OR PRI-QPL-AS8

24、5720 AS APPLICABLE FOR THIS STANDARD. SEE www.eAuditN FOR CURRENT QPL ONLINE. /6/ IDENTIFICATION AT LOCATION SHOWN: MARK PER AS478 CLASS C OR D, OR METHOD 7A3, 15A3, OR 15B, MANUFACTURERS IDENTIFICATION, CAGE CODE NUMBER OR TRADEMARK, BASIC PART NUMBER, MATERIAL CODE LETTER, AND TUBE WALL CODE. /7/

25、THIS PART IS DESIGNED FOR USE IN SYSTEMS WITH MAXIMUM OPERATING PRESSURES SHOWN IN TABLE 1B WITH RECOMMENDATION THAT THE MINIMUM WALL THICKNESS OF THE TUBING WELDED TO THE AS4697 FITTING END OF PORT #2 BE THE VALUE SHOWN FOR THE APPROPRIATE OPERATING PRESSURE IN ARP4698. THINNER WALL THICKNESSES MAY

26、 BE USED. /8/ IF PORT #2 IS STYLE A, D WILL EXTEND THROUGHOUT THE PART AND C WILL NOT APPLY. 9. INTERPRETATION OF DRAWING PER AS4296. 10. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES SHALL BE 125 MICROINCHES Ra. SURFACES OF HEX

27、 FLATS ON NUT MAY BE 250 MICROINCHES Ra. 11. BREAK EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED. 12. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. 13. DIMENSIONS ARE IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .010, ANGULAR DIMENSIONS 030. TABLE 2 TABLE 2A - FITTINGS, WE

28、LDED END, MEET THE PERFORMANCE REQUIREMENTS OF AS4510 AND AS4510/2, 5000 PSI SYSTEM DASH NUMBER TUBE WALL CODE FITTING PART NUMBER RECOMMENDED PRESSURE (PSI) MAX TITANIUM 15-5 CRES 17-4 CRES -03 .018 AS4227T03-018 AS4227V03-018 AS4227P03-018 5000 -03 .022 AS4227T03-022 AS4227V03-022 AS4227P03-022 50

29、00 -04 .022 AS4227T04-022 AS4227V04-022 AS4227P04-022 5000 -05 .028 AS4227T05-028 AS4227V05-028 AS4227P05-028 5000 -06 .032 AS4227T06-032 AS4227V06-032 AS4227P06-032 5000 -08 .043 AS4227T08-043 AS4227V08-043 AS4227P08-043 5000 -10 .055 AS4227T10-055 AS4227V10-055 AS4227P10-055 5000 -12 .065 AS4227T1

30、2-065 AS4227V12-065 AS4227P12-065 5000 -16 .089 AS4227T16-089 AS4227V16-089 AS4227P16-089 5000 AEROSPACE STANDARD AS4227 SHEET 5 OF 5 REV. C FITTING ASSEMBLY, ADAPTER, INTERNAL THREAD, BEAM SEAL TO INTEGRAL WELD RING TABLE 2B - FITTINGS, WELDED END, MEET THE PERFORMANCE REQUIREMENTS OF AS4510 AND AS

31、4510/2, 4000 PSI SYSTEM AND BELOW DASH NUMBER TUBE WALL CODE FITTING PART NUMBER RECOMMENDED PRESSURE (PSI) MAX TITANIUM 15-5 CRES 17-4 CRES -05 .022 AS4227T05-022 AS4227V05-022 AS4227P05-022 4000 -06 .022 AS4227T06-022 AS4227V06-022 AS4227P06-022 3000 -06 .028 AS4227T06-028 AS4227V06-028 AS4227P06-

32、028 4000 -08 .022 AS4227T08-022 AS4227V08-022 AS4227P08-022 2000 -10 .028 AS4227T10-028 AS4227V10-028 AS4227P10-028 2000 -10 .043 AS4227T10-043 AS4227V10-043 AS4227P10-043 4000 -12 .028 AS4227T12-028 AS4227V12-028 AS4227P12-028 2000 -12 -055 AS4227T12-055 AS4227V12-055 AS4227P12-055 4000 -14 .032 AS

33、4227T14-032 AS4227V14-032 AS4227P14-032 2000 -14 .065 AS4227T14-065 AS4227V14-065 AS4227P14-065 4000 -16 .043 AS4227T16-043 AS4227V16-043 AS4227P16-043 2000 -16 .078 AS4227T16-078 AS4227V16-078 AS4227P16-078 4000 -20 .055 AS4227T20-055 AS4227V20-055 AS4227P20-055 2000 -20 .089 AS4227T20-089 AS4227V2

34、0-089 AS4227P20-089 4000 -24 .055 AS4227T24-055 AS4227V24-055 AS4227P24-055 2000 /14/ EXAMPLE OF PART NUMBER: PART NUMBER AS4227T04-022 REPRESENTS 1/4 INCH TITANIUM FITTING ADAPTER, BEAM SEAL TO INTEGRAL WELD RING, .022 INCH NOMINAL TUBE WALL WITH STYLE B PORT #2, 5000 PSI MAXIMUM RECOMMENDED PRESSU

35、RE. 15. REFERENCED DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATION FOR BID (THIS NOTE IS FOR GOVERNMENT PROCUREMENT ONLY). 16. IN THE EVENT OF A CONFLICT BETWEEN THE TEXT OF THIS STANDARD AND THE REFERENCES CITED HEREIN, THE TEXT OF THIS STANDARD SHALL TAKE PRECEDENCE. 17 USERS OF TH

36、IS STANDARD ARE ADVISED TO CONTROL SOURCE APPROVAL(S) BY STANDARD PAGE SUPPLEMENT SHEET OR SIMILAR MEANS WHILE PRI-QPL IS UNDER THE DEVELOPMENT. 18 INVENTORIED PARTS CONFORMING TO THE PREVIOUS ISSUE MAY BE USED TO DEPLETION. 19. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR

37、THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE

38、 NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS4227 T 04 - 022 TUBE WALL CODE THE CODE IS LARGEST SIZE NOMINAL TUBE WALL THICKNESS IN THE RANGE OF NOMINAL TUBE WALLS SHOWN, IN .001 INCREMENTS SIZE CODE TUBE SIZE IN .062 INCREMENTS MATERIAL CODE LETTER /1/ BASIC SPECIFICATION SHEET NUMBER