SAE AS 4200B-2017 FITTING ASSEMBLY ADAPTER RING LOCKED PORT CONNECTION TO BEAM SEAL 8000 PSI.pdf

《SAE AS 4200B-2017 FITTING ASSEMBLY ADAPTER RING LOCKED PORT CONNECTION TO BEAM SEAL 8000 PSI.pdf》由会员分享，可在线阅读，更多相关《SAE AS 4200B-2017 FITTING ASSEMBLY ADAPTER RING LOCKED PORT CONNECTION TO BEAM SEAL 8000 PSI.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD FITTING ASSEMBLY, ADAPTER RING LOCKED PORT CONNECTION TO BEAM SEAL 8000 PSI AS4200Copyright 2017 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical,

2、 photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED1992-06 REAFFIRMED 201

3、5-04 REVISED2017-10THIRD ANGLE PROJECTION CUSTODIAN: G-3/G-3B REV.BFEDERAL SUPPLY CLASS 4730 AS4200 SHEET 1 OF 3 REV. B PROCUREMENT SPECIFICATION: AS85720 /4/ SAETechnicalStandardsBoard Rulesprovidethat:“Thisreportispublished bySAEto advance the state oftechnicaland engineering sciences.The use ofth

4、isreportisentirelyvoluntary,anditsapplicabilityandsuitabilityforanyparticularuse,includinganypatentinfringementarising therefrom,isthe sole responsibilityoftheuser.”SAEreviewseachtechnicalreportatleasteveryfiveyearsatwhich time itmaybe revised,reaffirmed,stabilized,orcancelled.SAEinvitesyourwritten

5、commentsandsuggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/standards.sae.org/AS4200B RATIONALE ADD AMS5732, AMS5737, AND AMS5853 OPTIONS FOR A286 LOCKRING MATERIAL. EXCEPTION TAKEN TO SOLID FILM LUBRICANT REQUIREMENT OF FITTING END SPECIFICATION. F

6、IGURE 1 - ADAPTER, ASSEMBLY TABLE 1 - DIMENSIONS TABLE 1A - A THROUGH F AEROSPACE STANDARD AS4200 SHEET 2 OF 3 REV. B FITTING ASSEMBLY, ADAPTER RING LOCKED PORT CONNECTION TO BEAM SEAL 8000 PSI TABLE 1B - G THROUGH N NOTES 1. MATERIAL: a. FITTING: 6Al-4V TITANIUM ALLOY PER AMS4928, AMS4965, OR AMS49

7、67 b. LOCKRING: A286 CORROSION RESISTANT STEEL PER AMS5731, AMS5732, AMS5734, AMS5737, OR AMS5853 2. HEAT TREATMENT: a. FITTING: 140 KSI UTS MIN b. LOCKRING: 34-40 HRC 3. FINISH: a. FITTING: ANODIC TREATMENT PER AMS2488, TYPE 2 b. LOCKRING: PASSIVATE PER AMS2700, TYPE 2 AND POLYTETRAFLUOROETHYLENE C

8、OATING (COLOR: ORANGE) /4/ PROCUREMENT SPECIFICATION: AS85720 EXCEPT AS SPECIFIED ON THIS STANDARD. THIS PART SHALL BE QUALIFIED TO THE PROCUREMENT SPECIFICATION IN A COMPLETE ASSEMBLY. USERS OF THIS STANDARD ARE ADVISED TO CONTROL SOURCE APPROVAL(S) BY STANDARD PAGE SUPPLEMENT SHEET OR SIMILAR MEAN

9、S. /5/ SEALING SURFACE: NO VISIBLE DEFECTS. TO BE PROTECTED FOR SHIPMENT /6/ LOCKRING RETAINED ON FITTING BY CONTROLLED INTERFERENCE FIT. FOUR TEETH, APPROXIMATELY 90 APART HAVE BEEN REMOVED FROM THE LOCKRING EXTERNAL SERRATION FOR 8000 PSI IDENTIFICATION PURPOSES. /7/ SEALING ANGLES: a. SIZES -02 A

10、ND -03: 300 TO 330 b. SIZES -04 AND LARGER: 830 TO 900 8. IDENTIFICATION PER AS478 CLASS 35D. NAME, TRADEMARK OR CAGE CODE, AND PART NUMBER. /9/ WORKING PRESSURE: PARTS ARE DESIGNED FOR USE IN 8000 PSI WORKING PRESSURE SYSTEMS COMPATIBLE WITH TITANIUM. THE USE OF ODD SIZES (-03, -05, -07, -09, AND -

11、11) IS RECOMMENDED. THE USE OF EVEN SIZES (-02, -04, -06, -08, AND -10) IS OPTIONAL AND SHALL BE THE RESPONSIBILITY OF THE DESIGN ACTIVITY. 10. ADAPTERS TO BE INSTALLED PER AS4202 INTO BOSS CAVITIES PER AS4201. 11. INVENTORIED PARTS CONFORMING TO THE PREVIOUS “LETTER CHANGE” MAY BE USED TO DEPLETION

12、. 12. INTERPRETATION OF DRAWING PER AS4296. 13. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 MICROINCHES Ra AND SEALING SURFACE TO BE 63 MICROINCHES Ra. 14. BREAK EDGES .003 TO .015, UNLESS OTHERWISE SPECIFIED. AEROSP

13、ACE STANDARD AS4200 SHEET 3 OF 3 REV. B FITTING ASSEMBLY, ADAPTER RING LOCKED PORT CONNECTION TO BEAM SEAL 8000 PSI 15. DIMENSIONING AND TOLERANCING: ANSI Y14.5M-1982. 16. DIMENSIONS ARE IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .005, ANGULAR DIMENSIONS 5. /17/ EXAMPLE OF

14、PART NUMBER: 18. REVISION INDICATOR: A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.