SAE AS 4200A-1994 Fitting Assembly Adapter Ring Locked Port Connection to Beam Seal 8000 psi《FSC 4730适配器环锁紧端口连接到梁密封8 000 psi的配件总成》.pdf

《SAE AS 4200A-1994 Fitting Assembly Adapter Ring Locked Port Connection to Beam Seal 8000 psi《FSC 4730适配器环锁紧端口连接到梁密封8 000 psi的配件总成》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 4200A-1994 Fitting Assembly Adapter Ring Locked Port Connection to Beam Seal 8000 psi《FSC 4730适配器环锁紧端口连接到梁密封8 000 psi的配件总成》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、SAETechnicalStandardsBoardRulesprovidethat:“ThisreportispublishedbySAEtoadvancethestateoftechnicalandengineeringsciences.Theuseofthisreportisentirelyvoluntary,anditsapplicabilityandsuitabilityforanyparticularuse,includinganypatentinfringementarisingtherefrom,isthesoleresponsibilityoftheuser.”SAErevi

2、ewseachtechnicalreportatleasteveryfiveyearsatwhichtimeitmaybereaffirmed,revised,orcancelled.SAEinvitesyourwrittencommentsandsuggestions.SHEET 1 OF 3AS4200REV.ATHIRD ANGLE PROJECTIONAEROSPACE STANDARDAS4200 REV. AISSUED1992-06REVISED1994-07REAFFIRMED2004-07FITTING ASSEMBLY, ADAPTER RING LOCKED PORT C

3、ONNECTION TO BEAM SEAL 8000 psiCUSTODIAN: SAE G-3/G-3B PROCUREMENT SPECIFICATION: /4/ MIL-F-85720FEDERAL SUPPLY CLASS 4730FIGURE 1 - ADAPTER, ASSEMBLYTABLE 1 - DIMENSIONSTABLE 1A - A THROUGH FCopyright 2004 SAE International All rights reserved. No part of this publication may be reproduced, stored

4、in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email:

5、 custsvcsae.org SAE WEB ADDRESS: http:/www.sae.org Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-FITTING ASSEMBLY, ADAPTER RING LOCKED PORT CONNECTION TO BEAM SEAL 8000 psiAEROSPACE STANDARD AS4200SH

6、EET 2 OF 3AS4200REV.AREV. ATABLE 1B - G THROUGH NNOTES:1. MATERIAL:a. FITTING: 6Al-4V TITANIUM ALLOY PER AMS 4928, AMS 4965, OR AMS 4967b. LOCKRING: A286 CORROSION RESISTANT STEEL PER AMS 5731 OR AMS 57342. HEAT TREATMENT:a. FITTING: 140 ksi UTS MINb. LOCKRING: 34-40 HRC3. FINISH:a. FITTING: ANODIC

7、TREATMENT PER AMS 2488, TYPE 2b. LOCKRING: PASSIVATE PER QQ-P-35, TYPE II AND POLYTETRAFLUOROETHYLENE COATING (COLOR: ORANGE)/4/ PROCUREMENT SPECIFICATION: MIL-F-85720 EXCEPT AS SPECIFIED ON THIS STANDARD. THIS PART SHALL BE QUALIFIED TO THE PROCUREMENT SPECIFICATION IN A COMPLETE ASSEMBLY. USERS OF

8、 THIS STANDARD ARE ADVISED TO CONTROL SOURCE APPROVAL(S) BY STANDARD PAGE SUPPLEMENT SHEET OR SIMILAR MEANS./5/ SEALING SURFACE: NO VISIBLE DEFECTS. TO BE PROTECTED FOR SHIPMENT/6/ LOCKRING RETAINED ON FITTING BY CONTROLLED INTERFERENCE FIT. FOUR TEETH, APPROXIMATELY 90 APART HAVE BEEN REMOVED FROM

9、THE LOCKRING EXTERNAL SERRATION FOR 8000 psi IDENTIFICATION PURPOSES./7/ SEALING ANGLES:a. SIZES -02 AND -03: 300 TO 330b. SIZES -04 AND LARGER: 830 TO 9008. IDENTIFICATION PER AS478 CLASS 35D. NAME, TRADEMARK OR CAGE CODE, AND PART NUMBER./9/ WORKING PRESSURE: PARTS ARE DESIGNED FOR USE IN 8000 psi

10、 WORKING PRESSURE SYSTEMS COMPATIBLE WITH TITANIUM. THE USE OF ODD SIZES (-03, -05, -07, -09, AND -11) IS RECOMMENDED. THE USE OF EVEN SIZES (-02, -04, -06, -08, AND -10) IS OPTIONAL AND SHALL BE THE RESPONSIBILITY OF THE DESIGN ACTIVITY.10. ADAPTERS TO BE INSTALLED PER AS4202 INTO BOSS CAVITIES PER

11、 AS4201.11. INVENTORIED PARTS CONFORMING TO THE PREVIOUS “LETTER CHANGE” MAY BE USED TO DEPLETION.12. INTERPRETATION OF DRAWING PER ARP4296.13. SURFACE TEXTURE: SYMBOLS PER ANSI Y14.36; REQUIREMENTS PER ANSI/ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 in Ra AND SEALING SURFAC

12、E TO BE 63 in Ra.14. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED.Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-FITTING ASSEMBLY, ADAPTER RING LOCKED PORT CONNECTION TO BEAM SEAL 8000 psiAEROS

13、PACE STANDARD AS4200SHEET 3 OF 3AS4200REV.AREV. ANOTES (Continued):15. DIMENSIONING AND TOLERANCING: ANSI Y14.5M16. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .005, ANGULAR DIMENSIONS 5./17/ EXAMPLE OF PART NUMBER:Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-