SAE AS 4136C-2016 CROSS STANDARD AND REDUCER REDUCED BODY FLARELESS.pdf

《SAE AS 4136C-2016 CROSS STANDARD AND REDUCER REDUCED BODY FLARELESS.pdf》由会员分享，可在线阅读，更多相关《SAE AS 4136C-2016 CROSS STANDARD AND REDUCER REDUCED BODY FLARELESS.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD CROSS, STANDARD AND REDUCER, REDUCED BODY, FLARELESS AS4136Copyright 2016 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recordin

2、g, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED1992-11 REVISED2016-05THIRD ANGLE PROJECTION

3、CUSTODIAN: G-3/G-3B REV.C FEDERAL SUPPLY CLASS 4730 AS4136 SHEET 1 OF 4 REV. C PROCUREMENT SPECIFICATION: AS18280, SEE NOTE 4 SAE Technical Standards BoardRules providethat:“This reportis publishedbySAE toadvancethestateof technicaland engineering sciences. The use of this report isentirely voluntar

4、y, andits applicability andsuitability for any particularuse, includingany patentinfringement arising therefrom,is the soleresponsibility of theuser.”SAE reviews eachtechnical reportatleast every fiveyears atwhichtimeitmay berevised,reaffirmed, stabilized,orcancelled. SAE invites yourwrittencomments

5、 andsuggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AS4136C RATIONALE CORRECT TYPOGRAPHICAL ERRORS IN TABLE 3. FIGURE 1 - CROSS, REDUCED BODY, FLARELESS AEROSPACE STANDARD AS4136 SHEET 2 OF 4 REV. C CROSS, STANDARD A

6、ND REDUCER, REDUCED BODY, FLARELESS TABLE 1 - DIMENSIONS AND WEIGHTS BASIC NO. AS4136 /18/ SIZE CODE H MIN J P .030 LB/EA APPROX REF CRES LB/EA APPROX REF TI 04 .050 .390 .030 .072 .040 05 .050 .453 .159 .083 .047 06 .050 .453 .137 .112 .063 08 .050 .577 .140 .217 .122 10 .070 .702 .157 .342 .192 12

7、 .080 .890 .166 .512 .288 16 .090 1.140 .174 .763 .428 20 .110 1.390 .071 1.200 .674 24 .130 1.640 - 1.537 .863 TABLE 2 - FITTING END SIZE CODE TUBE OD T THREAD PER AS8879 CLASS 3A D E 04 .250 .4375-20UNJF .371 .350 05 .313 .5000-20UNJF .371 .412 06 .375 .5625-18UNJF .379 .453 08 .500 .7500-16UNJF .

8、461 .577 10 .625 .8750-14UNJF .511 .702 12 .750 1.0625-12UNJ .556 .890 16 1.000 1.3125-12UNJ .556 1.140 20 1.250 1.6250-12UNJ .556 1.390 24 1.500 1.8750-12UNJ .556 1.640 TABLE 3 - LEG LENGTH A FORGING SIZE 04 05 06 08 10 12 16 20 24 04 .898 - - - - - - - - 05 .961 .961 - - - - - - - 06 1.039 1.039 1

9、.055 - - - - - - 08 1.164 1.164 1.180 1.273 - - - - - 10 1.258 1.258 1.274 1.367 1.430 - - - - 12 1.351 1.351 1.367 1.460 1.523 1.586 - - - 16 1.507 1.507 1.523 1.616 1.679 1.742 1.742 - - 20 1.663 1.663 1.679 1.772 1.835 1.898 1.898 1.898 - 24 1.788 1.788 1.804 1.897 1.960 2.023 2.023 2.023 2.023 A

10、EROSPACE STANDARD AS4136 SHEET 3 OF 4 REV. C CROSS, STANDARD AND REDUCER, REDUCED BODY, FLARELESS NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. /1/ MATERIAL a. CODE LETTER J: TYPE 304

11、 CORROSION RESISTANT STEEL PER AMS5639 b. CODE LETTER T: TYPE 6Al-4V TITANIUM ALLOY PER AMS4928 c. CODE LETTER V: TYPE 15-5PH CORROSION RESISTANT STEEL PER AMS5659 2. HEAT TREATMENT a. MATERIAL CODE LETTER J: NONE b. MATERIAL CODE LETTER T: NONE c. MATERIAL CODE LETTER V: HEAT TREAT TO CONDITION H-1

12、075 PER AMS2759/3 /3/ FINISH a. MATERIAL CODE LETTER J: PASSIVATE PER AMS2700 TYPE 6 OR 7 b. MATERIAL CODE LETTER T: FLUORIDE PHOSPHATE CONVERSION COAT PER AMS2486 c. MATERIAL CODE LETTER V: (1) NO SUFFIX FINISH CODE LETTER: PASSIVATE PER AMS2700 TYPE 2 OR 8 (2) SUFFIX FINISH CODE LETTER “P”; CADMIU

13、M PLATE PER AMS-QQ-P-416, TYPE II, CLASS 2 /4/ PROCUREMENT SPECIFICATION: AS18280 UNLESS SPECIFIED OTHERWISE ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER AS LISTED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST (QPL)

14、PRI-QPL-AS18280 FOR THIS STANDARD. SEE http:/www.eAuditN FOR CURRENT QPL ONLINE. /5/ IDENTIFICATION AT LOCATION SHOWN: MARK PER AS478 CLASS C OR D OR METHOD 7A3, 15A3, OR 15B. a. FOR SIZES 06 (.375 OD TUBE SIZE) AND SMALLER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, LETTERS “AS”, MATERIAL CODE LET

15、TER AND FORGING MANUFACTURERS IDENTIFICATION WHEN MADE FROM FORGING b. FOR SIZES 08 (.500 OD TUBE SIZE) AND LARGER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, BASIC PART NUMBER, MATERIAL CODE LETTER AND FORGING MANUFACTURERS IDENTIFICATION WHEN MADE FROM FORGING 6. THIS PART IS INTENDED FOR USE IN

16、SYSTEMS WITH OPERATING PRESSURES AS FOLLOWS: a. SIZES -04 THROUGH -16 AT 3000 PSI b. SIZES -20 AND -24 AT 1500 PSI NOTE: OPERATING PRESSURES HAVE BEEN CHANGED FROM 4000 PSI AND 2000 PSI TO 3000 PSI AND 1500 PSI TO COMPLY WITH AS18280 SYSTEM PRESSURE REQUIREMENTS. USERS OF THIS STANDARD FOR 4000 PSI

17、SYSTEM APPLICATIONS ARE ADVISED TO CONTROL SOURCE APPROVAL BY STANDARD PAGE SUPPLEMENT OR SIMILAR MEANS. 7. WHEN MACHINED FROM BAR OR OVERSIZED FORGING, THE CENTER BODY SECTION SHALL CONFORM TO AS1376, TABLE 2. /8/ RADIUS APPLICABLE TO TITANIUM PARTS ONLY. 9. BREAK EDGES .003 TO .015 UNLESS OTHERWIS

18、E SPECIFIED. 10. THIS PART IS A REDUCED BODY VERSION OF MS21906 IF NONREDUCER, OR AS1006 IF REDUCER. AEROSPACE STANDARD AS4136 SHEET 4 OF 4 REV. C CROSS, STANDARD AND REDUCER, REDUCED BODY, FLARELESS /11/ SPECIFY END SIZES IN THIS ORDER: LARGEST END FIRST (PORT #1), OPPOSITE END ON RUN SECOND (PORT

19、#2), LARGEST END ON SIDE THIRD (PORT #3), OPPOSITE END FOURTH (PORT #4). 12. LARGEST END DETERMINES FORGING SIZE. /13/ APPLICABLE ONLY TO REDUCERS AND SIZE 04 AND 05 NONREDUCERS. 14. INTERPRETATION OF DRAWING PER ARP4296. 15. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UN

20、LESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 MICROINCHES Ra. 16. DIMENSIONS AND TOLERANCING: ANSI Y14.5M-1982 17. DIMENSIONS IN INCHES, UNLESS OTHERWISE SPECIFIED. TOLERANCES: LINEAR DIMENSIONS .016, ANGULAR DIMENSIONS .5q. /18/ EXAMPLE OF PART NUMBER: 19. REVISION INDICATOR: A CHANGE BAR (

21、l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNIC

22、AL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. 20. INVENTORIED PARTS CONFORMING TO THE PREVIOUS LETTER CHANGE MAY BE USED TO DEPLETION. SIZE CODE, TUBE SIZE OF PORT #4 IN .062 INCH INCREMENTS /11/ SIZE CODE, TUBE SIZE OF PORT #3 IN .062 INCH INCREMENTS /11/ SIZE CODE, TUBE SIZE OF PORT #2 IN .062 INCH INCREMENTS /11/ SIZE CODE, TUBE SIZE OF PORT #1 IN .062 INCH INCREMENTS /11/