SAE AS 4133B-2013 TEE STANDARD AND REDUCER REDUCED BODY FLARELESS《非扩口 简化型体 标准和减径管 三通》.pdf

《SAE AS 4133B-2013 TEE STANDARD AND REDUCER REDUCED BODY FLARELESS《非扩口 简化型体 标准和减径管 三通》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 4133B-2013 TEE STANDARD AND REDUCER REDUCED BODY FLARELESS《非扩口 简化型体 标准和减径管 三通》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARD TEE, STANDARD AND REDUCER, REDUCED BODY, FLARELESS AS4133Copyright 2013 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording,

2、or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1992-11REVISED 2013-08THIRD ANGLE PROJECTION CU

3、STODIAN: G-3/G-3B REV.BFEDERAL SUPPLY CLASS 4730 AS4133SHEET 1 OF 4REV. BPROCUREMENT SPECIFICATION: /4/ AS18280SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirely voluntary, andits a

4、pplicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirmed, revised, orcancelled. SAE invites yourwrittencomments andsuggestions

5、. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS4133BRATIONALE THE PRI-QPL NOTE AND CADMIUM WARNING NOTE HAVE BEEN REVISED. CLARIFICATIONS TO PASSIVATION NOTE AND INTENDED USE NOTE HAVE BEEN ADDED, AND UPDATES MADE. FIGURE 1

6、TEE, REDUCED BODY, FLARELESS AEROSPACE STANDARD AS4133SHEET 2 OF 4REV. BTEE, STANDARD AND REDUCER, REDUCED BODY, FLARELESS TABLE 1 DIMENSIONS AND WEIGHTS BASIC NO. AS4133/18/SIZE CODE HMIN J P.030 LB/EAAPPROX REF CRESLB/EAAPPROX REF TI04 .050 .390 .030 .055 .031 05 .050 .453 .159 .068 .038 06 .050 .

7、453 .137 .080 .046 08 .050 .577 .140 .142 .081 10 .070 .702 .157 .264 .151 12 .080 .890 .166 .385 .221 16 .090 1.140 .174 .588 .338 20 .110 1.390 .071 1.141 .663 24 .130 1.640 - 1.470 .850 TABLE 2 FITTING END SIZECODE TUBE OD T THREAD PER AS8879 CLASS 3A D E 04 .250 .4375-20UNJF .371 .350 05 .313 .5

8、000-20UNJF .371 .412 06 .375 .5625-18UNJF .379 .453 08 .500 .7500-16UNJF .461 .577 10 .625 .8750-14UNJF .511 .702 12 .750 1.0625-12UNJF .556 .890 16 1.000 1.3125-12UNJ .556 1.140 20 1.250 1.6250-12UNJ .556 1.39024 1.500 1.8750-12UNJ .556 1.640 TABLE 3 LEG LENGTH A FORGING SIZE 04 05 06 08 10 12 16 2

9、0 24 04 .898 - - - - - - - -05 .961 .961 - - - - - - - 06 1.039 1.039 1.055 - - - - - -08 1.164 1.164 1.180 1.273 - - - - -10 1.258 1.258 1.274 1.367 1.430 - - - - 12 1.351 1.351 1.367 1.460 1.523 1.586 - - -16 1.507 1.507 1.523 1.616 1.679 1.742 1.742 - -20 1.663 1.663 1.679 1.772 1.835 1.896 1.896

10、 1.898 - 24 1.788 1.788 1.804 1.897 1.960 2.023 2.023 2.023 2.023AEROSPACE STANDARD AS4133SHEET 3 OF 4REV. BTEE, STANDARD AND REDUCER, REDUCED BODY, FLARELESS NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CON

11、CERNING CADMIUMS USE. /1/ MATERIAL a. CODE LETTER J: TYPE 304 CORROSION RESISTANT STEEL PER AMS5639 b. CODE LETTER T: TYPE 6AL-4V TITANIUM ALLOY PER AMS4928 c. CODE LETTER V: TYPE 15-5PH CORROSION RESISTANT STEEL PER AMS5659 2. HEAT TREATMENT a. MATERIAL CODE LETTER J: NONE b. MATERIAL CODE LETTER T

12、: NONE c. MATERIAL CODE LETTER V: HEAT TREAT TO CONDITION H-1075 PER AMS2759/3 /3/ FINISH a. MATERIAL CODE LETTER J: PASSIVATE PER AMS2700 TYPE 6 OR 7 b. MATERIAL CODE LETTER T: FLUORIDE PHOSPHATE CONVERSION COAT PER AMS2486 c. MATERIAL CODE LETTER V: (1) NO SUFFIX FINISH CODE LETTER: PASSIVATE PER

13、AMS2700 TYPE 2 OR 8 (2) SUFFIX FINISH CODE LETTER “P”; CADMIUM PLATE PER AMS-QQ-P-416, TYPE II, CLASS 2 /4/ PROCUREMENT SPECIFICATION: AS18280 UNLESS SPECIFIED OTHERWISE ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER AS LISTED IN THE PERF

14、ORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST (QPL) PRI-QPL-AS18280 FOR THIS STANDARD. SEE HTTP:/WWW.EAUDITNET.COMFOR CURRENT QPL ONLINE. /5/ IDENTIFICATION AT LOCATION SHOWN: MARK PER AS478 CLASS C OR D OR METHOD 7A3, 15A3, OR 15B. a. FOR SIZES 06 (.375 OD TUBE SIZE) AND SMALLER: MANUFACTU

15、RERS NAME, CAGE CODE OR TRADEMARK, LETTERS “AS”, MATERIAL CODE LETTER AND FORGING MANUFACTURERS IDENTIFICATION WHEN MADE FROM FORGING b. FOR SIZES 08 (.500 OD TUBE SIZE) AND LARGER: MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, BASIC PART NUMBER, MATERIAL CODE LETTER AND FORGING MANUFACTURERS IDENTIFI

16、CATION WHEN MADE FROM FORGING 6. THIS PART IS INTENDED FOR USE IN SYSTEMS WITH OPERATING PRESSURES AS FOLLOWS: a. SIZES -04 THRU -16 AT 3000 psi b. SIZES -20 AND -24 AT 1500 psi NOTE: OPERATING PRESSURES HAVE BEEN CHANGED FROM 4000 PSI AND 2000 PSI TO 3000 PSI AND 1500 PSI TO COMPLY WITH AS18280 SYS

17、TEM PRESSURE REQUIREMENTS. USERS OF THIS STANDARD FOR 4000 PSI SYSTEM APPLICATIONS ARE ADVISED TO CONTROL SOURCE APPROVAL BY STANDARD PAGE SUPPLEMENT OR SIMILAR MEANS. 7. WHEN MACHINED FROM BAR OR OVERSIZED FORGING, THE CENTER BODY SECTION SHALL CONFORM TO AS1376, TABLE 2. /8/ RADIUS APPLICABLE TO T

18、ITANIUM PARTS ONLY. 9. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 10. THIS PART IS A REDUCED BODY VERSION OF MS21905 IF NONREDUCER, OR AS1005 IF REDUCER. /11/ SPECIFY END SIZES IN THIS ORDER: LARGEST PORT ON RUN FIRST AS PORT #1, OPPOSITE PORT ON RUN SECOND AS PORT #2, SIDE PORT THIRD AS P

19、ORT #3. AEROSPACE STANDARD AS4133SHEET 4 OF 4REV. BTEE, STANDARD AND REDUCER, REDUCED BODY, FLARELESS 12. LARGEST END DETERMINES FORGING SIZE. /13/ APPLICABLE ONLY TO REDUCERS AND SIZE 04 AND 05 NONREDUCERS. 14. INTERPRETATION OF DRAWING PER ARP4296. 15. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; RE

20、QUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 in Ra. 16. DIMENSIONS AND TOLERANCING: ANSI Y14.5M-1982 17. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .016, ANGULAR DIMENSIONS .5 DEGREES. /18/ EXAMPLE OF PART NUMBER: 19. A CHANG

21、E BAR (|) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.