SAE AS 39029 34B-2010 Contacts Electrical Connector Pin Crimp Removable (for MIL-DTL-28748 3 and MIL-C-28748 13 Connectors)《压盖可拆式针形电气连接器触头(适用于AS50151系列 AS34001连接器)》.pdf

《SAE AS 39029 34B-2010 Contacts Electrical Connector Pin Crimp Removable (for MIL-DTL-28748 3 and MIL-C-28748 13 Connectors)《压盖可拆式针形电气连接器触头(适用于AS50151系列 AS34001连接器)》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 39029 34B-2010 Contacts Electrical Connector Pin Crimp Removable (for MIL-DTL-28748 3 and MIL-C-28748 13 Connectors)《压盖可拆式针形电气连接器触头(适用于AS50151系列 AS34001连接器)》.pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARD (R) CONTACTS, ELECTRICAL CONNECTOR, PIN, CRIMP REMOVABLE (FOR MIL-DTL-28748/3 AND MIL-DTL-28748/13 CONNECTORS) AS39029/34Copyright 2010 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or

2、 by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/ww

3、w.sae.org ISSUED 2000-07REAFFIRMED 2007-06 REVISED 2010-12THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C1 REV.BFEDERAL SUPPLY CLASS 5999 AS39029/34SHEET 1 OF 4REV. BPROCUREMENT SPECIFICATION: AS39029SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of

4、technicalandengineering sciences. Theuse ofthis report is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time it

5、may bereaffirmed, revised, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS39029/34BRATIONALE REVISE TO INCORPORATE THE OUTSTANDING AMENDMENT AS REQUIRED BY SAE GUIDE

6、LINES AND UPDATE FORMAT, FIGURES AND TABLES. NOTICE THE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIST OF THIS SPECIFICATION SHEET AND THE LATEST ISSUE OF SAE AS39029. FIGURE 1- AS39029/34 PIN CONTACT Copyright SAE International Provided by IHS under license with SAENot for Re

7、saleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS39029/34SHEET 2 OF 4REV. B(R) CONTACTS, ELECTRICAL CONNECTOR, PIN, CRIMP REMOVABLE (FOR MIL-DTL-28748/3 AND MIL-DTL-287848/13 CONNECTORS) TABLE 1A - CONTACT DIMENSIONS BINCODE ADIABDIACDIADDIAEDIAFDIAGDIA H

8、DIA271.121.119.070.067.048.044.079.076.119MAX.135MAX.101.099.041.039272.0635 .0615 273.095.092.070.066.112.109440.077.074.057.054.037.034.070.067.077.074.078 MAX.061.058.031.029TABLE 1B CONTACT DIMENSIONS (CONTINUED) BINCODE J K L M N P R SDIA 1/271.319.299.695.675.771.757.075.055.265.245.545.525.51

9、0.490.034.028272273440.175.155.587.567.625.605.045.025.145.125.510.490.450.430.023.0171/ HOLE ONE WALL LOCATED ON C AXIS WITHIN .008 INCHES. TABLE 2 - MARKING AND DESIGN CHARACTERISTICS BIN CODE COLOR BANDS MATING ENDSIZEWIREBARREL SIZETYPE CLASS1ST2ND3RD271 RED VIOLET BROWN 20 20 A A 272 RED VIOLET

10、 RED 16 20 273 RED VIOLET ORANGE 16 16 440 YELLOW YELLOW BLACK 22 22 Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS39029/34SHEET 3 OF 4REV. B(R) CONTACTS, ELECTRICAL CONNECTOR,

11、 PIN, CRIMP REMOVABLE (FOR MIL-DTL-28748/3 AND MIL-DTL-287848/13 CONNECTORS) TABLE 3 - TOOL REQUIREMENTS BINCODE BASICCRIMPING TOOL POSITIONER INSTALLINGTOOL REMOVAL TOOL 271 M22520/1-01 M22520/1-03 REDM81969/18-01 M81969/20-01 272 M22520/1-01 M22520/1-03 BLUEM81969/18-01 M81969/20-01 273 M22520/1-0

12、1 M22520/1-03 BLUEM81969/18-01 M81969/20-01 440 M22520/2-01 K187 1/ OR 640092 2/ OR EQUIVALENT M81969/18-02 M81969/20-02 1/ DANIELS MANUFACTURING CORPORATION PART NUMBER 2/ ASTRO TOOL CORPORATION PART NUMBER TABLE 4 - PART NUMBERS AS39029 PART NUMBER BINCODE SUPERSEDEDPART NUMBER(S) M39029/34-271 27

13、1 MS17803-20-20 M39029/34-272 272 MS17803-16-20M39029/34-273 273 MS17803-16-16 M39029/34-440 440 M39029/34-22-22 REQUIREMENTS: ALL REQUIREMENTS SHALL CONSIST OF THIS SPECIFICATION AND THE LATEST ISSUE OF AS39029. 1. DESIGN: CONTACT SHALL BE DESIGNED IN ACCORDANCE WITH FIGURE 1, TABLE 1 AND 2. WALL T

14、HICKNESS OF ANY PART OF THE CONTACT SHALL NOT BE LESS THAN 0.010 (0.25 MM). DIMENSIONS ARE IN INCHES AND SHOWN AFTER PLATING. UNLESS OTHERWISE SPECIFIED, SPHERICAL END DIMENSIONS SHALL CONFORM TO AS39029. 2. TOOLS: TOOLS REQUIRED FOR CRIMPING CONTACTS TO WIRE/CABLE AND THE INSTALLING/REMOVAL FROM TH

15、E CONNECTOR SHALL BE IN ACCORDANCE WITH TABLE 3. 3. PART NUMBERS: CONTACT PART NUMBERS SHALL BE IN ACCORDANCE WITH TABLE 4. SUPERSEDED PART NUMBERS ARE AS SPECIFIED. 4. MATERIALS: MATERIALS SHALL BE IN ACCORDANCE WITH AS39029. 5. MECHANICAL: MECHANICAL PROPERTIES SHALL BE IN ACCORDANCE WITH AS39029.

16、 6. ELECTRICAL: ELECTRICAL PROPERTIES SHALL BE IN ACCORDANCE WITH AS39029. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS39029/34SHEET 4 OF 4REV. B(R) CONTACTS, ELECTRICAL CONN

17、ECTOR, PIN, CRIMP REMOVABLE (FOR MIL-DTL-28748/3 AND MIL-DTL-287848/13 CONNECTORS) 7. ENVIRONMENTAL: ENVIRONMENTAL PROPERTIES SHALL BE IN ACCORDANCE WITH AS39029. VIBRATION IS TEST CONDITION II. SHOCK IS TEST CONDITION I. APPLICATION NOTES: 1. THE AS39029/34 PIN CONTACT MATES DIRECTLY INTO AN AS3902

18、9/35 SOCKET AS SHOWN IN TABLE 5. TABLE 5 - CONTACT MATING PART NUMBERS AS39029/34 BIN CODE MATING AS39029/35 BIN CODE 271 274 272 275 273 276 440 441 SPECIFICATION NOTES: A CHANGE BAR (|) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT E

19、DITORIAL CHANGES HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-