SAE AS 3585A-2009 Pin and Plug Expansion Set of Parts Cres 416 or 416SE STD and 010 Oversize Diameters Short UNS S41600 UNS S41623《UNS S41600 UNS S41623短型416或416SE标准及 010特大直径成套零件Cr.pdf

《SAE AS 3585A-2009 Pin and Plug Expansion Set of Parts Cres 416 or 416SE STD and 010 Oversize Diameters Short UNS S41600 UNS S41623《UNS S41600 UNS S41623短型416或416SE标准及 010特大直径成套零件Cr.pdf》由会员分享，可在线阅读，更多相关《SAE AS 3585A-2009 Pin and Plug Expansion Set of Parts Cres 416 or 416SE STD and 010 Oversize Diameters Short UNS S41600 UNS S41623《UNS S41600 UNS S41623短型416或416SE标准及 010特大直径成套零件Cr.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARD (R) PIN AND PLUG, EXPANSION, SET OF PARTS CRES, 416 OR 416SE, STD AND .010 OVERSIZE DIAMETERS, SHORT, UNS S41600/UNS S41623 AS3585Copyright 2009 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in an

2、y form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: ht

3、tp:/www.sae.org ISSUED 1996-06REAFFIRMED 2006-10 REVISED 2009-02THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.AFEDERAL SUPPLY CLASS 5340 AS3585SHEET 1 OF 2REV. APROCUREMENT SPECIFICATION: NONESAE TechnicalStandards Board Rules provide that: “This report is published by SAE toadvance thestate of technic

4、al andengineering sciences. Theuse of thisreport is entirely voluntary, andits applicabilityandsuitability forany particularuse, including any patent infringement arising therefrom, is thesole responsibility oftheuser.”SAE reviews each technical report at least every five yearsat which time it may b

5、e reaffirmed, revised, orcancelled. SAE invites yourwritten commentsandsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS3585ARATIONALE ADD MANUFACTURERS PART NUMBERS, CLARIFY PART MARKING REQUIREMENTS AND GENERAL SA

6、E UPDATING REQUIREMENTS FOR FORMATING. FIGURE 1 - AS3128 PIN FIGURE 2 - AS3127 PLUG TABLE 1 - PART NUMBERS AEROSPACE STANDARD PARTNUMBER /3/MANUFACTURERSPARTNUMBER /3/PIN SIZE PLUG SIZE APPROX MASSLB/100 AS3585-01 PLGA0930020A AS3128-01 AS3127-01 .017 AS3585-02 PLGA1250020A AS3128-02 AS3127-02 .037

7、AS3585-03 PLGA1560020A AS3128-03 AS3127-03 .060 AS3585-04 PLGA1870020A AS3128-04 AS3127-04 .110 AS3585-05 PLGA2180020A AS3128-05 AS3127-05 .182 AS3585-06 PLGA2500020A AS3128-06 AS3127-06 .275 AS3585-07 PLGA2810020A AS3128-07 AS3127-07 .419 AS3585-08 PLGA3430020A AS3128-08 AS3127-08 .704 AS3585-09 PL

8、GA4060020A AS3128-09 AS3127-09 1.161 AS3585-10 PLGA4680020A AS3128-10 AS3127-10 1.709 AS3585-11 PLGA5310020A AS3128-11 AS3127-11 2.923 AS3585-12 PLGA6560020A AS3128-12 AS3127-12 4.642 AS3585-51 PLGA1030020A AS3128-01 AS3127-51(a) .019 AS3585-52 PLGA1350020A AS3128-02 AS3127-52(a) .044 AS3585-53 PLGA

9、1660020A AS3128-03 AS3127-53(a) .067 AS3585-54 PLGA1970020A AS3128-04 AS3127-54(a) .122 AS3585-55 PLGA2280020A AS3128-05 AS3127-55(a) .202 AS3585-56 PLGA2600020A AS3128-06 AS3127-56(a) .269 (a) DESIGNATES .010 OVERSIZED PLUGS. Copyright SAE International Provided by IHS under license with SAENot for

10、 ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS3585SHEET 2 OF 2REV. A(R) PIN AND PLUG, EXPANSION, SET OF PARTS CRES, 416 OR 416SE, STD AND .010 OVERSIZE DIAMETERS, SHORT, UNS S41600/UNS S41623 TABLE 1 - PART NUMBERS (CONTINUED) AEROSPACE STANDARD PAR

11、TNUMBER /3/MANUFACTURERSPARTNUMBER /3/PIN SIZE PLUG SIZE APPROX MASSLB/100 AS3585-57 PLGA2910020A AS3128-07 AS3127-57(a) .444 AS3585-58 PLGA3530020A AS3128-08 AS3127-58(a) .744 AS3585-59 PLGA4160020A AS3128-09 AS3127-59(a) 1.226 AS3585-60 PLGA4780020A AS3128-10 AS3127-60(a) 1.786 AS3585-61 PLGA54100

12、20A AS3128-11 AS3127-61(a) 3.017 AS3585-62 PLGA6660020A AS3128-12 AS3127-62(a) 4.830 (a) DESIGNATES .010 OVERSIZED PLUGS. NOTES: 1. MATERIAL: AMS5610 (416 OR 416SE CRES BAR), UNS S41600 OR UNS S41623, 20 TO 34 HRC REF. 2. FINISH: a. PLUG: SEE AS3127 b. PIN: SEE AS3128 /3/ MARK AS3585-( ) PART NUMBER

13、 AND MANUFACTURERS PART NUMBER ON PACKAGE IN ACCORDANCE WITH AS478, METHOD 37. IN ADDITION, PACKAGES FOR OVERSIZE PLUGS SHALL INCLUDE “OVERSIZE 416 SS” IN A RECTANGULAR BLOCK. 4. SEE AIR3276 FOR HOLE PREPARATION AND AIR3277 FOR INSTALLATION PROCEDURE. 5. PIN AND PLUG EXPANSION SET OF PARTS SHALL CON

14、TAIN A PIN SIZE FROM AS3128 AND A PLUG SIZE FROM AS3127 AS SPECIFIED WITH THE CORRESPONDING DASH NUMBER IN TABLE 1. 6. AS, AIR AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. 7. A CHANGE BAR ( l ) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS,

15、NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORI

16、AL CHANGES ONLY. APPROVED SOURCE OF SUPPLY: THE LEE CO WESTBROOK, CT FEDERAL SUPPLY CODE FOR MANUFACTURERS NO 92555. ONLY THE ITEM DESCRIBED ON THIS DRAWING WHEN PROCURED FROM THE VENDOR LISTED HEREON IS APPROVED FOR USE IN THE APPLICATIONS SPECIFYING THIS AEROSPACE STANDARD IDENTIFICATION NUMBER. A

17、 SUBSTITUTE ITEM SHALL NOT BE USED WITHOUT PRIOR TESTING AND APPROVAL BY THE DESIGN ACTIVITY RESPONSIBLE FOR THE APPLICATION. IDENTIFICATION OF THE APPROVED SOURCE HEREON IS NOT TO BE CONSTRUED AS A GUARANTEE OF PRESENT OR CONTINUED AVAILABILITY AS A SOURCE OF SUPPLY FOR THE ITEM DESCRIBED ON THE DRAWING. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-