SAE AS 34201A-2011 Adapter Cable Clamp to Cable Bushing Telescoping《伸缩套管电缆夹到电缆接头》.pdf

《SAE AS 34201A-2011 Adapter Cable Clamp to Cable Bushing Telescoping《伸缩套管电缆夹到电缆接头》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 34201A-2011 Adapter Cable Clamp to Cable Bushing Telescoping《伸缩套管电缆夹到电缆接头》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARD ADAPTER, CABLE CLAMP TO CABLE, BUSHING, TELESCOPING AS34201Copyright 2011 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording

2、, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2004-06STABILIZED 2011-12THIRD ANGLE PROJECTI

3、ON CUSTODIAN: AE-8/AE-8C1 REV.AFEDERAL SUPPLY CLASS 5935 AS34201SHEET 1 OF 3REV. APROCUREMENT SPECIFICATION: NONESAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirely voluntary, andits

4、 applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments

5、andsuggestionsSAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS34201ARATIONALE THIS PRODUCT HAS BEEN SUPERSEDED BY AS85049/139 FOR NEW DESIGN APPLICATIONS, HOWEVER THE C1 COMMITTEE HAS DETERMINED THIS DETAIL SHEET SHOULD BE STAB

6、ILIZED TO ALLOW FOR LEGACY APPLICATION USAGE. STABILIZED NOTICE THIS DOCUMENT HAS BEEN DECLARED “STABILIZED” BY THE AE-8 TECHNICAL COMMITTEE AND WILL NO LONGER BE SUBJECTED TO PERIODIC REVIEWS FOR CURRENCY. USERS ARE RESPONSIBLE FOR VERIFYING REFERENCES AND CONTINUED SUITABILITY OF TECHNICAL REQUIRE

7、MENTS. NEWER TECHNOLOGY MAY EXIST. NOTICE THIS DOCUMENT HAS BEEN TAKEN DIRECTLY FROM U.S. MILITARY SPECIFICATION MS3420C, NOTICE 3 AND CONTAINS ONLY MINOR EDITORIAL AND FORMAT CHANGES REQUIRED TO BRING IT INTO CONFORMANCE WITH THE PUBLISHING REQUIREMENTS OF SAE TECHNICAL STANDARDS. THE INITIAL RELEA

8、SE OF THIS DOCUMENT IS INTENDED TO REPLACE MS3420C, NOTICE 3. ANY PART NUMBERS ESTABLISHED BY THE ORIGINAL SPECIFICATION REMAIN UNCHANGED. THE ORIGINAL MILITARY SPECIFICATION WAS ADOPTED AS AN SAE STANDARD UNDER THE PROVISIONS OF THE SAE TECHNICAL STANDARDS BOARD (TSB) RULES AND REGULATIONS (TSB 001

9、) PERTAINING TO ACCELERATED ADOPTION OF GOVERNMENT SPECIFICATIONS AND STANDARDS. TSB RULES PROVIDE FOR (A) THE PUBLICATION OF PORTIONS OF UNREVISED GOVERNMENT SPECIFICATIONS AND STANDARDS WITHOUT CONSENSUS VOTING AT THE SAE COMMITTEE LEVEL, AND (B) THE USE OF THE EXISTING GOVERNMENT SPECIFICATION OR

10、 STANDARD FORMAT. UNDER DEPARTMENT OF DEFENSE POLICIES AND PROCEDURES, ANY QUALIFICATION REQUIREMENTS AND ASSOCIATED QUALIFIED PRODUCTS LISTS ARE MANDATORY FOR DOD CONTRACTS. ANY REQUIREMENT RELATING TO QUALIFIED PRODUCTS LISTS (QPLS) HAS NOT BEEN ADOPTED BY SAE AND IS NOT PART OF THIS TECHNICAL REP

11、ORT. Copyright SAE International Provided by IHS under license with SAENot for Resale-,-,-AEROSPACE STANDARD AS34201SHEET 2 OF 3REV. AADAPTER, CABLE CLAMP TO CABLE, BUSHING, TELESCOPING DASHNO. ADIABDIACDIA D E, F, G RADIUS SUPERSEDES (REF.) AN3420 DASH NO. MS39056 DASH NO. -3 .130 .210 .379 2.875 .

12、031 -3 -1 -4 .220 .302 .505 2.750 .031 -4 -2 -6 .312 .427 .619 2.625 .031 -6 -3 -8 .437 .552 .744 2.500 .062 -8 -4 -10 .562 .615 .889 2.375 .062 -10 -5 -12 .625 .740 1.084 2.250 .062 -12 -6 -16 .750 .927 1.314 2.125 .062 -16 -7 -20 .937 1.240 1.598 2.000 .062 -20 -8 -24 1.250 1.365 1.847 1.875 .062

13、-24 -9 -28 1.375 1.614 2.085 1.750 .062 -28 -10 -32 1.624 1.864 2.335 1.625 .062 -32 -11 -40 1.874 2.364 2.835 1.500 .062 -40 -12 INCHES MM INCHES MM INCHES MM INCHES MM INCHES MM .002.016.031.062.130.210.220.302.312.379.427.05 .41 .79 1.57 3.30 5.33 5.59 7.67 7.92 9.63 10.85 .437 .505.552.562.615.6

14、19.625.740.744.750.88911.10 12.83 14.02 14.27 15.62 15.72 15.88 18.80 18.90 19.05 22.58 .927 .937 1.084 1.240 1.250 1.314 1.365 1.375 1.500 1.598 23.55 23.80 27.53 31.50 31.75 33.38 34.67 34.93 38.10 40.59 1.614 1.624 1.625 1.750 1.847 1.864 1.874 1.875 2.000 2.085 41.00 41.25 41.28 44.45 46.91 47.3

15、5 47.60 47.63 50.80 52.96 2.125 2.250 2.335 2.364 2.375 2.500 2.625 2.750 2.835 2.875 53.98 57.15 59.31 60.05 60.33 63.50 66.68 69.85 72.01 73.03 NOTES: 1. MATERIAL: RUBBER PER MIL-STD-417. TYPE SC515A1B1C1E3E5F2GM. 2. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: FRACTIONS 1/32; DEC

16、IMALS .016. INTERPRET DIMENSIONING AND TOLERANCING IN ACCORDANCE WITH ANSI Y14.5-1973. 3. FOR USE WITH CLAMP, CABLE, ELECTRICAL CONNECTOR MS3057-3A THRU MS3057-40A AND MS3057-3C THRU -40C. 4. FOR DESIGN FEATURE PURPOSES, THIS STANDARD TAKES PRECEDENCE OVER PROCUREMENT DOCUMENTS REFERENCED HEREIN. 5.

17、 REFERENCE DOCUMENTS SHALL BE OF THE ISSUE IN EFFECT ON DATE OF INVITATIONS FOR BID. 6. EXAMPLE PART NO.: MS3420-3 DASH NO. _ Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHSAEROSPACE STANDARD AS34201SHEE

18、T 3 OF 3REV. AADAPTER, CABLE CLAMP TO CABLE, BUSHING, TELESCOPING DASHNO. ADIABDIASUPERSEDES (REF.) AN3420 DASH NO. MS39057 DASH NO. -3 .125 .210 -3A -1 -4 .219 .302 -4A -2 -6 .312 .427 -6A -3 -8 .438 .531 -8A -4 -10 .438 .615 -10A -5 -12 .541 .740 -12A -6 -16 .750 .927 -16A -7 -18 .938 1.115 -18A -

19、8 -20 .938 1.240 -20A -9 -24 1.125 1.365 -24A -10 -28 1.250 1.614 -28A -11 -32 1.625 1.865 -32A -12 -40 1.875 2.365 -40A -13 INCHES MM INCHES MM INCHES MM INCHES MM .031.125.210.219.302.312.427.79 3.18 5.33 5.56 7.67 7.92 10.85 .438 .531.541.615.740.750.92711.13 13.49 13.74 15.62 18.80 19.05 23.55 .

20、938 1.115 1.125 1.240 1.250 1.365 23.83 28.32 28.58 31.50 31.75 34.67 1.614 1.625 1.865 1.875 2.000 2.365 41.00 41.28 47.37 47.63 50.80 60.07 NOTES: 1. MATERIAL: A. RUBBER PER MIL-STD-417. TYPE SC515A1B1C1E3E5F2GM (BLACK). D. SILICONE RUBBER PER ZZ-R-765 CLASS 3A OR 3B (RED). L. FLUOROSILICONE RUBBE

21、R PER ZZ-R-765 CLASS 2A OR 2B GRADE 50 (BLUE). 2. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: DECIMALS .016. INTERPRET DIMENSIONING AND TOLERANCING IN ACCORDANCE WITH ANSI Y14.5-1973. 3. FOR USE WITH CLAMP, CABLE, ELECTRICAL CONNECTOR MS3057-3B THRU MS3057-40B AND MS3057-3C THRU -4

22、0C, MS3415, MS3417 AND MS3418. 4. EXAMPLE PART NO.: MS3420-20 L DASH NO. _ MATERIAL _ CALLOUT MS3420C IS INACTIVE FOR NEW DESIGN AND IS NO LONGER USED, EXCEPT FOR REPLACEMENT PURPOSES. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS