SAE AS 3414B-2016 BOLT MACHINE - HEXAGON HEAD PD SHANK UNS N07718 185 KSI 2500-28 UNJF-3A (STRESS RUPTURE RESISTANT).pdf

《SAE AS 3414B-2016 BOLT MACHINE - HEXAGON HEAD PD SHANK UNS N07718 185 KSI 2500-28 UNJF-3A (STRESS RUPTURE RESISTANT).pdf》由会员分享，可在线阅读，更多相关《SAE AS 3414B-2016 BOLT MACHINE - HEXAGON HEAD PD SHANK UNS N07718 185 KSI 2500-28 UNJF-3A (STRESS RUPTURE RESISTANT).pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARDBOLT, MACHINE - HEXAGON HEAD, PD SHANKUNS N07718, 185 KSI, .2500-28 UNJF-3A(STRESS RUPTURE RESISTANT)AS3414Copyright 2016 SAE InternationalAll rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, e

2、lectronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA)Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.orgISSUED198

3、5-12REVISED2016-10THIRD ANGLE PROJECTIONCUSTODIAN: E-25REV. BFEDERAL SUPPLY CLASS5306AS3414SHEET 1 OF 3REV.BPROCUREMENT SPECIFICATION: AS7467 /3/SAETechnical Standards BoardRules providethat:“This reportis publishedby SAE to advance thestateoftechnical andengineering sciences. The useofthis reportis

4、 entirely voluntary, and its applicability and suitability forany particularuse, includingany patent infringement arising therefrom, is thesole responsibility of theuser.”SAE reviews eachtechnical reportatleastevery fiveyears at whichtime it may berevised, reaffirmed, stabilized, or cancelled. SAEin

5、vites your written comments and suggestions.SAE values your input. To provide feedback on thisTechnical Report, please visit http:/standards.sae.org/AS3414BRATIONALEUPDATE STRAIGHTNESS FCF, ADD EDGE DISTANCE EXCEPTION FOR HEAD MARKING. ADD AS3062, CHANGEEND CHAMFER ANGLE FROM REF TO APPROX. ADD SURF

6、ACE TEXTURE REQUIREMENT TO WRENCH FLATS, ADD RUNOUT REQUIREMENT TO EDGE OF BEARING SURFACE, ADD EXISTING INVENTORY USE NOTE. UPDATE FPI REQUIREMENT, FIGURE 1 RE-DRAWN, GENERAL EDITORIAL UPDATE.FIGURE 1 - BOLTAEROSPACE STANDARDAS3414SHEET 2 OF 3REV.BBOLT, MACHINE - HEXAGON HEAD, PD SHANKUNS N07718, 1

7、85 KSI, .2500-28 UNJF-3A(STRESS RUPTURE RESISTANT)TABLE 1 - DIMENSIONS L, G, K, AND APPROXIMATE MASSPARTNUMBER LGMINKMAXAPPROX MASSLB/100AS3414-04AS3414-05AS3414-06AS3414-07AS3414-08AS3414-09AS3414-10AS3414-11AS3414-12AS3414-13AS3414-14AS3414-15AS3414-16AS3414-17AS3414-18AS3414-19AS3414-20AS3414-21A

8、S3414-22AS3414-23AS3414-24AS3414-25AS3414-26AS3414-27AS3414-28AS3414-29AS3414-30AS3414-31AS3414-32AS3414-33AS3414-34AS3414-35AS3414-36AS3414-37AS3414-38AS3414-39AS3414-40AS3414-41AS3414-42AS3414-43AS3414-44AS3414-45AS3414-46AS3414-47AS3414-48AS3414-49AS3414-50AS3414-51AS3414-52AS3414-53.365- .385.42

9、8- .448.490- .510.552- .572.615- .635.678- .698.740- .760.802- .822.865- .885.928- .948.990-1.0101.052-1.0721.115-1.1351.178-1.1981.240-1.2601.302-1.3221.365-1.3851.428-1.4481.490-1.5101.552-1.5721.615-1.6351.678-1.6981.740-1.7601.802-1.8221.865-1.8851.928-1.9481.990-2.0102.115-2.1352.240-2.2602.365

10、-2.3852.490-2.5102.615-2.6352.740-2.7602.865-2.8852.990-3.0103.115-3.1353.240-3.2603.365-3.3853.490-3.5103.615-3.6353.740-3.7603.865-3.8853.990-4.0104.115-4.1354.240-4.2604.365-4.3854.490-4.5104.615-4.6354.740-4.7604.865-4.885.025.025.025.025.025.025.025.025.025.057.119.181.244.307.369.431.494.557.6

11、19.681.744.807.869.931.9941.0571.1191.2441.3691.4941.6191.7441.8691.9942.1192.2442.3692.4942.6192.7442.8692.9943.1193.2443.3693.4943.6193.7443.8693.994.099.099.099.099.099.099.099.099.125.188.250.312.375.438.500.562.625.688.750.812.875.9381.0001.0621.1251.1881.2501.3751.5001.6251.7501.8752.0002.1252

12、.2502.3752.5002.6252.7502.8753.0003.1253.2503.3753.5003.6253.7503.8754.0004.1251.061.131.201.271.341.421.491.561.631.711.791.861.942.012.092.162.242.312.392.462.542.612.692.762.842.912.993.143.293.443.593.743.894.044.194.344.494.644.794.945.095.245.395.545.695.855.996.156.296.45AEROSPACE STANDARDAS3

13、414SHEET 3 OF 3REV.BBOLT, MACHINE - HEXAGON HEAD, PD SHANKUNS N07718, 185 KSI, .2500-28 UNJF-3A(STRESS RUPTURE RESISTANT)TABLE 1 - DIMENSIONS L, G, K, AND APPROXIMATE MASS (CONTINUED)PARTNUMBER LGMINKMAXAPPROX MASSLB/100AS3414-54AS3414-55AS3414-56AS3414-57AS3414-58AS3414-59AS3414-60AS3414-61AS3414-6

14、24.990-5.0105.115-5.1355.240-5.2605.365-5.3855.490-5.5105.615-5.6355.740-5.7605.865-5.8855.990-6.0104.1194.2444.3694.4944.6194.7444.8694.9945.1194.2504.3754.5004.6254.7504.8755.0005.1255.2506.596.756.897.057.197.357.497.657.79NOTES/1/ FOR PART NUMBERS AS3414-04 THROUGH AS3414-18 DATUM A SHALL REPLAC

15、E DATUM B.2. MATERIAL: CORROSION AND HEAT RESISTANT NICKEL ALLOY AMS5662 (UNS N07718)./3/ PROCUREMENT SPECIFICATION: AS7467 EXCEPT ROLL THREAD AND COLD WORK FILLET RADIUS AFTER PRECIPITATION HARDENING.4. FLUORESCENT PENETRANT INSPECTION PER ASTM E1417/E1417M TYPE 1, SENSITIVITY LEVEL 2 MINIMUM.5. SU

16、RFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1 UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra EXCEPT UPSET HEAD TO BE 250 MICROINCHES Ra.6. BREAK SHARP EDGES .003 TO .015 UNLESS OTHERWISE STATED.7. DIMENSIONS ARE IN INCHES.8. DIMENSIONING AND TOLERANCING PER ANSI

17、 Y14.5M-1982 (ASME PUBLICATION).9. UNLESS OTHERWISE SPECIFIED, PART INVENTORY MANUFACTURED TO PREVIOUS REVISIONS OF THE APPLICABLE DRAWING OR SPECIFICATION MAY BE PROCURED AND USED UNTIL STOCK IS DEPLETED.10. DO NOT USE UNASSIGNED PART NUMBERS.11. REVISION INDICATOR: A CHANGE BAR (I) LOCATED IN THE

18、LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS.ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION.ASTM IS AN ASTM INTERNATIONAL PUBLICATION.