SAE AS 3405A-2015 BOLT MACHINE - HEXAGON HEAD DRILLED 6 HOLES PD SHANK AMS5708 (UNS N07001) 2500-28 UNJF-3A.pdf

《SAE AS 3405A-2015 BOLT MACHINE - HEXAGON HEAD DRILLED 6 HOLES PD SHANK AMS5708 (UNS N07001) 2500-28 UNJF-3A.pdf》由会员分享，可在线阅读，更多相关《SAE AS 3405A-2015 BOLT MACHINE - HEXAGON HEAD DRILLED 6 HOLES PD SHANK AMS5708 (UNS N07001) 2500-28 UNJF-3A.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、 AEROSPACE STANDARD BOLT, MACHINE - HEXAGON HEAD, DRILLED 6 HOLES, PD SHANK, AMS5708 (UNS N07001), .2500-28 UNJF-3A AS3405Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, ele

2、ctronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED19

3、85-08REAFFIRMED 2006-10 REVISED2015-09THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.AFEDERAL SUPPLY CLASS 5306 AS3405 SHEET 1 OF 3 REV. A PROCUREMENT SPECIFICATION: AS7471 SAETechnicalStandardsBoard Rulesprovidethat:“Thisreportispublished bySAEto advance the state oftechnicaland engineering sciences.Th

4、e use ofthisreportisentirelyvoluntary,anditsapplicabilityandsuitabilityforanyparticularuse,includinganypatentinfringementarising therefrom,isthe sole responsibilityoftheuser.”SAEreviewseachtechnicalreportatleasteveryfiveyears atwhich time itmaybe revised,reaffirmed,stabilized,orcancelled.SAEinvitesy

5、ourwritten commentsandsuggestions.SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AS3405A RATIONALE UPDATE THREAD SPECIFICATION TO AS8879, UPDATE TO ANSI Y14.5M-1982, REVISE FPI REQUIREMENTS TO ASTM E1417/E1417M, ADD EDGE DISTAN

6、CE EXCEPTION FOR HEAD MARKING, REVISE HEX DIMENSIONS TO CURRENT PRACTICE, ADD AS3062 FOR THREAD RUNOUT, FIGURE 1 REDRAWN, UPDATE REFERENCES, AND GENERAL EDITORIAL UPDATE. FIGURE 1 - BOLT AEROSPACE STANDARD AS3405 SHEET 2 OF 3 REV. A BOLT, MACHINE - HEXAGON HEAD, DRILLED 6 HOLES, PD SHANK, AMS5708 (U

7、NS N07001), .2500-28 UNJF-3A TABLE 1 - PART NUMBERS AND DIMENSIONS PART NO. L G MIN K MAX APPROX. MASS LB/100 PART NO. L G MIN K MAX APPROX. MASS LB/100 AS3405-04 .365- .385 .025 .099 1.48 AS3405-34 2.490-2.510 1.619 1.750 4.00 AS3405-05 .428- .448 .025 .099 1.55 AS3405-35 2.615-2.635 1.744 1.875 4.

8、16 AS3405-06 .490- .510 .025 .099 1.62 AS3405-36 2.740-2.760 1.869 2.000 4.32 AS3405-07 .552- .572 .025 .099 1.70 AS3405-37 2.865-2.885 1.994 2.125 4.46 AS3405-08 .615- .635 .025 .099 1.77 AS3405-38 2.990-3.010 2.119 2.250 4.62 AS3405-09 .678- .698 .025 .099 1.84 AS3405-39 3.115-3.135 2.244 2.375 4.

9、76 AS3405-10 .740- .760 .025 .099 1.91 AS3405-40 3.240-3.260 2.369 2.500 4.92 AS3405-11 .802- .822 .025 .099 1.99 AS3405-41 3.365-3.385 2.494 2.625 5.06 AS3405-12 .865- .885 .025 .125 2.06 AS3405-42 3.490-3.510 2.619 2.750 5.22 AS3405-13 .928- .948 .057 .188 2.13 AS3405-43 3.615-3.635 2.744 2.875 5.

10、36 AS3405-14 .990-1.010 .119 .250 2.20 AS3405-44 3.740-3.760 2.869 3.000 5.52 AS3405-15 1.052-1.072 .181 .312 2.29 AS3405-45 3.865-3.885 2.994 3.125 5.66 AS3405-16 1.115-1.135 .244 .375 2.36 AS3405-46 3.990-4.010 3.119 3.250 5.82 AS3405-17 1.178-1.198 .307 .438 2.43 AS3405-47 4.115-4.135 3.244 3.375

11、 5.96 AS3405-18 1.240-1.260 .369 .500 2.50 AS3405-48 4.240-4.260 3.369 3.500 6.12 AS3405-19 1.302-1.322 .431 .562 2.59 AS3405-49 4.365-4.385 3.494 3.625 6.26 AS3405-20 1.365-1.385 .494 .625 2.66 AS3405-50 4.490-4.510 3.619 3.750 6.42 AS3405-21 1.428-1.448 .557 .688 2.73 AS3405-51 4.615-4.635 3.744 3

12、.875 6.56 AS3405-22 1.490-1.510 .619 .750 2.80 AS3405-52 4.740-4.760 3.869 4.000 6.72 AS3405-23 1.552-1.572 .681 .812 2.89 AS3405-53 4.865-4.885 3.994 4.125 6.86 AS3405-24 1.615-1.635 .744 .875 2.96 AS3405-54 4.990-5.010 4.119 4.250 7.02 AS3405-25 1.678-1.698 .807 .938 3.03 AS3405-55 5.115-5.135 4.2

13、44 4.375 7.16 AS3405-26 1.740-1.760 .869 1.000 3.10 AS3405-56 5.240-5.260 4.369 4.500 7.32 AS3405-27 1.802-1.822 .931 1.062 3.19 AS3405-57 5.365-5.385 4.494 4.625 7.46 AS3405-28 1.865-1.885 .994 1.125 3.26 AS3405-58 5.490-5.510 4.619 4.750 7.62 AS3405-29 1.928-1.948 1.057 1.188 3.33 AS3405-59 5.615-

14、5.635 4.744 4.875 7.76 AS3405-30 1.990-2.010 1.119 1.250 3.40 AS3405-60 5.740-5.760 4.869 5.000 7.92 AS3405-31 2.115-2.135 1.244 1.375 3.56 AS3405-61 5.865-5.885 4.994 5.135 8.06 AS3405-32 2.240-2.260 1.369 1.500 3.70 AS3405-62 5.990-6.010 5.119 5.250 8.22 AS3405-33 2.365-2.385 1.494 1.625 3.86 NOTE

15、S: /1/ FOR PART NUMBERS AS3405-04 THRU AS3405-18 DATUM A SHALL REPLACE DATUM B. 2. MATERIAL: AMS5708 CORROSION AND HEAT RESISTANT NICKEL ALLOY (COMPOSITION SIMILAR TO UNS N07001). 3. PROCUREMENT SPECIFICATION: AS7471. 4. FLUORESCENT PENETRANT INSPECTION PER ASTM E1417/E1417M, TYPE 1, SENSITIVITY LEV

16、EL 2 MIN. 5. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra. EXCEPT UPSET HEAD TO BE 250 MICROINCHES Ra. 6. BREAK SHARP EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 7. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPEC

17、IFIED, TOLERANCES: ANGULAR DIMENSIONS 5. 8. DIMENSIONS AND TOLERANCING ANSI Y14.5M-1982 (ASME PUBLICATION). 9. DO NOT USE UNASSIGNED PART NUMBERS. AEROSPACE STANDARD AS3405 SHEET 3 OF 3 REV. A BOLT, MACHINE - HEXAGON HEAD, DRILLED 6 HOLES, PD SHANK, AMS5708 (UNS N07001), .2500-28 UNJF-3A 10. REVISIO

18、N INDICATOR: A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE

19、DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN ASTM INTERNATIONAL PUBLICATION.