SAE AS 3403A-2015 BOLT MACHINE - HEXAGON HEAD DRILLED 1 HOLE PD SHANK AMS5708 (UNS N07001) 3750-24 UNJF-3A.pdf

《SAE AS 3403A-2015 BOLT MACHINE - HEXAGON HEAD DRILLED 1 HOLE PD SHANK AMS5708 (UNS N07001) 3750-24 UNJF-3A.pdf》由会员分享，可在线阅读，更多相关《SAE AS 3403A-2015 BOLT MACHINE - HEXAGON HEAD DRILLED 1 HOLE PD SHANK AMS5708 (UNS N07001) 3750-24 UNJF-3A.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARD BOLT, MACHINE - HEXAGON HEAD, DRILLED 1 HOLE, PD SHANK, AMS5708 (UNS N07001), .3750-24 UNJF-3A AS3403Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, elect

2、ronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 198

3、5-08REAFFIRMED2006-10REVISED 2015-03THIRD ANGLE PROJECTION CUSTODIAN: E-25 REV.AFEDERAL SUPPLY CLASS 5306 AS3403SHEET 1 OF 3REV. APROCUREMENT SPECIFICATION: AS7471SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences.

4、Theuse ofthisreportis entirelyvoluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, is thesole responsibilityoftheuser.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized,

5、 orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS3403ARATIONALE UPDATE THREAD SPECIFICATION TO AS8879, UPDATE TO ANSI Y14.5M-1982, REVISE FPI REQUIREMENTS TO ASTM E14

6、17/1417M, ADD EDGE DISTANCE EXCEPTION FOR HEAD MARKING, REVISE ACROSS POINTS DIMENSION, ADD AS3062 FOR THREAD RUNOUT, FIGURE 1 REDRAWN, UPDATE REFERENCES, AND GENERAL EDITORIAL UPDATE. FIGURE 1 - BOLT AEROSPACE STANDARD AS3403SHEET 2 OF 3REV. ABOLT, MACHINE - HEXAGON HEAD, DRILLED 1 HOLE, PD SHANK,

7、AMS5708 (UNS N07001), .3750-24 UNJF-3ATABLE 1 - PART NUMBERS AND DIMENSIONS PART NO. L GMINKMAXAPPROX.MASSLB/100 PART NO. L GMINKMAXAPPROX.MASSLB/100 AS3403-03 .552- .572 .025 .108 3.14 AS3403-33 2.865-2.885 1.732 1.875 9.66 AS3403-04 .615- .635 .025 .108 3.31 AS3403-34 2.990-3.010 1.857 2.000 10.02

8、 AS3403-05 .678- .698 .025 .108 3.49 AS3403-35 3.115-3.135 1.982 2.125 10.37 AS3403-06 .740- .760 .025 .108 3.66 AS3403-36 3.240-3.260 2.107 2.250 10.72 AS3403-07 .802- .822 .025 .108 3.84 AS3403-37 3.365-3.385 2.232 2.375 11.07 AS3403-08 .865- .885 .025 .108 4.02 AS3403-38 3.490-3.510 2.357 2.500 1

9、1.43 AS3403-09 .928- .948 .025 .108 4.19 AS3403-39 3.615-3.635 2.482 2.625 11.78 AS3403-10 .990-1.010 .025 .108 4.37 AS3403-40 3.740-3.760 2.607 2.750 12.13 AS3403-11 1.052-1.072 .025 .108 4.54 AS3403-41 3.865-3.885 2.732 2.875 12.48 AS3403-12 1.115-1.135 .025 .125 4.72 AS3403-42 3.990-4.010 2.857 3

10、.000 12.84 AS3403-13 1.178-1.198 .045 .188 4.90 AS3403-43 4.115-4.135 2.982 3.125 13.20 AS3403-14 1.240-1.260 .107 .250 5.07 AS3403-44 4.240-4.260 3.107 3.250 13.55 AS3403-15 1.302-1.322 .169 .312 5.25 AS3403-45 4.365-4.385 3.232 3.375 13.90 AS3403-16 1.365-1.385 .232 .375 5.42 AS3403-46 4.490-4.510

11、 3.357 3.500 14.25 AS3403-17 1.428-1.448 .295 .438 5.60 AS3403-47 4.615-4.635 3.482 3.625 14.60 AS3403-18 1.490-1.510 .357 .500 5.78 AS3403-48 4.740-4.760 3.607 3.750 14.96 AS3403-19 1.552-1.572 .419 .562 5.95 AS3403-49 4.865-4.885 3.732 3.875 15.31 AS3403-20 1.615-1.635 .482 .625 6.13 AS3403-50 4.9

12、90-5.010 3.857 4.000 15.67 AS3403-21 1.678-1.698 .545 .688 6.30 AS3403-51 5.115-5.135 3.982 4.125 16.02 AS3403-22 1.740-1.760 .607 .750 6.48 AS3403-52 5.240-5.260 4.107 4.250 16.37 AS3403-23 1.802-1.822 .669 .812 6.65 AS3403-53 5.365-5.385 4.232 4.375 16.72 AS3403-24 1.865-1.885 .732 .875 6.84 AS340

13、3-54 5.490-5.510 4.357 4.500 17.08 AS3403-25 1.928-1.948 .795 .938 7.02 AS3403-55 5.615-5.635 4.482 4.625 17.43 AS3403-26 1.990-2.010 .857 1.000 7.19 AS3403-56 5.740-5.760 4.607 4.750 17.78 AS3403-27 2.115-2.135 .982 1.125 7.54 AS3403-57 5.865-5.885 4.732 4.875 18.13 AS3403-28 2.240-2.260 1.107 1.25

14、0 7.90 AS3403-58 5.990-6.010 4.857 5.000 18.48 AS3403-29 2.365-2.385 1.232 1.375 8.25 AS3403-30 2.490-2.510 1.357 1.500 8.60 AS3403-31 2.615-2.635 1.482 1.625 8.95 AS3403-32 2.740-2.760 1.607 1.750 9.30 AEROSPACE STANDARD AS3403SHEET 3 OF 3REV. ABOLT, MACHINE - HEXAGON HEAD, DRILLED 1 HOLE, PD SHANK

15、, AMS5708 (UNS N07001), .3750-24 UNJF-3ANOTES: /1/ FOR PART NUMBERS AS3403-03 THRU AS3403-21 DATUM A SHALL REPLACE DATUM B.2. MATERIAL: AMS5708 CORROSION AND HEAT RESISTANT NICKEL ALLOY (COMPOSITION SIMILAR TO UNS N07001). 3. PROCUREMENT SPECIFICATION: AS7471. 4. FLUORESCENT PENETRANT INSPECTION PER

16、 ASTM E1417/E1417M, TYPE 1, SENSITIVITY LEVEL 2 MIN. 5. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 125 MICROINCHES Ra. EXCEPT UPSET HEAD TO BE 250 MICROINCHES Ra. 6. BREAK SHARP EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 7.

17、DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: ANGULAR DIMENSIONS 5. 8. DIMENSIONS AND TOLERANCING ANSI Y14.5M-1982 (ASME PUBLICATION). 9. DO NOT USE UNASSIGNED PART NUMBERS. 10. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TEC

18、HNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. AS AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. ASTM IS AN ASTM INTERNATIONAL PUBLICATION.