SAE AS 33401A-2010 Bulkhead Bracket for Use with MS3367 Plastic Tiedown Straps《同MS3367塑料栓系皮带一起使用的舱壁支架》.pdf

《SAE AS 33401A-2010 Bulkhead Bracket for Use with MS3367 Plastic Tiedown Straps《同MS3367塑料栓系皮带一起使用的舱壁支架》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 33401A-2010 Bulkhead Bracket for Use with MS3367 Plastic Tiedown Straps《同MS3367塑料栓系皮带一起使用的舱壁支架》.pdf（2页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARD (R) BULKHEAD BRACKET FOR USE WITH MS3367 PLASTIC TIEDOWN STRAPS AS33401Copyright 2010 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopyin

2、g, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2004-04REVISED 2010-05THIRD ANGLE

3、 PROJECTION CUSTODIAN: AE-8/AE-8C2 REV.AFEDERAL SUPPLY CLASS 5975 AS33401SHEET 1 OF 2REV. APROCUREMENT SPECIFICATION: MIL-S-23190SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirely v

4、oluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirmed, revised, orcancelled. SAE invites yourwrittencomme

5、nts andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS33401ARATIONALE REDRAWN TO MAKE THE DRAWINGS AND CHARTS MORE LEGIBLE. NOTICE THE REQUIREMENTS FOR PROCURING THE MOUNTING BRACKET DESCRIBED HEREIN SHALL CONSIST

6、 OF THIS SPECIFICATION AND THE LATEST ISSUE OF SAE AS23190. FIGURE 1 - MS3340 MOUNTING BRACKET CONFIGURATION TABLE 1 FIGURE 1 DIMENSIONS DASHNO.A.030B.030C.030D.030EMINF.015G.030HMINK.030P.030R.015S.015T.030U.030PLASTICSTRAPSACCOMMODATEDREF.r1 1.100 .450 .700 .750 .195 .200 .250 .060 .550 .130 .060

7、.060 .210 .390MS3367r1,r2,&MS3367r5Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS33401SHEET 2 OF 2REV. A(R) BULKHEAD BRACKET FOR USE WITH MS3367 PLASTIC TIEDOWN STRAPS TABLE 2

8、COLOR DESCRIPTION COLORDASHNO.COLORr9 NATURALADDITIONAL REQUIREMENTS: 1. MATERIAL: NYLON PER ASTM D 4066-94B (REF. SAE AS23190). 2. REMOVE ALL BURRS AND SHARP EDGES. BREAK ALL SHARP CORNERS. MOLD MARKS AND NORMAL VENT FLASH ARE PERMISSIBLE.3. THE MINIMUM TENSILE STRENGTH SHALL BE 50 POUNDS. NOTES: 1

9、. ALL DIMENSIONS ARE IN INCHES. 2. EXAMPLE OF PART NUMBER: MS3340 - 1 - 9COLOR DASH NUMBER ITEM DASH NUMBER BASIC PART NUMBER 3. PART NUMBER SHALL APPEAR ON PACKAGE. APPLICATION NOTE: 1. AS33401 IS INACTIVE FOR NEW DESIGN AND IS NO LONGER USED, EXCEPT FOR REPLACEMENT PURPOSES. SPECIFICATION NOTE: 1.

10、 A CHANGE BAR (I) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN ( R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND ( R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-