SAE AS 22520 37-2013 CRIMPING TOOL TYPE 2 ELECTRICAL WIRE SPLICING HAND ACTUATED TYPE II FOR ENVIRONMENTAL SPLICES WIRE RANGE 26-12 AWG《环境用拼接线范围26-12AWG的Ⅱ类手动导线拼接电气2型卷边工具》.pdf

《SAE AS 22520 37-2013 CRIMPING TOOL TYPE 2 ELECTRICAL WIRE SPLICING HAND ACTUATED TYPE II FOR ENVIRONMENTAL SPLICES WIRE RANGE 26-12 AWG《环境用拼接线范围26-12AWG的Ⅱ类手动导线拼接电气2型卷边工具》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 22520 37-2013 CRIMPING TOOL TYPE 2 ELECTRICAL WIRE SPLICING HAND ACTUATED TYPE II FOR ENVIRONMENTAL SPLICES WIRE RANGE 26-12 AWG《环境用拼接线范围26-12AWG的Ⅱ类手动导线拼接电气2型卷边工具》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARD CRIMPING TOOL, TYPE 2, ELECTRICAL, WIRE SPLICING, HAND ACTUATED, TYPE II, FOR ENVIRONMENTAL SPLICES, WIRE RANGE 26-12 AWGAS22520/37Copyright 2013 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in a

2、ny form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS

3、: http:/www.sae.org ISSUED 2013-04THIRD ANGLE PROJECTION CUSTODIAN: AE-8/AE-8C2 FEDERAL SUPPLY CLASS 5120 AS22520/37SHEET 1 OF 3PROCUREMENT SPECIFICATION: AS22520SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. T

4、heuse ofthis report is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabiliz

5、ed, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS22520/37RATIONALE AS22520/37 PERMITS THE CANCELLATION AND SUPERSESSION OF MIL-DTL-22520/37 WITH THIS DOCUMENT. IT

6、INCLUDES APPLICABLE ENGINEERING POSITION LETTERS, MILITARY SPECIFICATION AMENDMENTS, AND MINOR TECHNICAL CHANGES REQUIRED TO REFLECT THE APPROVED QUALIFIED TOOLS. GOVERNMENT DOCUMENTATION REFERENCES ARE REMOVED. NOTICE THE COMPLETE REQUIREMENTS FOR PROCURING THE PRODUCT DESCRIBED HEREIN SHALL CONSIS

7、T OF THIS DOCUMENT AND THE LATEST ISSUE OF AS22520. FIGURE 1 - AS22520/37-01 BASIC CRIMPING TOOL AEROSPACE STANDARD AS22520/37SHEET 2 OF 3CRIMPING TOOL, TYPE 2, ELECTRICAL, WIRE SPLICING, HAND ACTUATED, TYPE II, FOR ENVIRONMENTAL SPLICES, WIRE RANGE 26-12 AWG LOCATORS FIGURE 2 - AS22520/37-01 CRIMP

8、JAW DETAILS AEROSPACE STANDARD AS22520/37SHEET 3 OF 3CRIMPING TOOL, TYPE 2, ELECTRICAL, WIRE SPLICING, HAND ACTUATED, TYPE II, FOR ENVIRONMENTAL SPLICES, WIRE RANGE 26-12 AWG TABLE 1 - AS22520/37 CONFIGURATION DETAILS WIRESIZEDIE COLOR CODE AS22520/39-01 INSPECTION GAGES RADIUS (INCHES) GO GAGE NO-G

9、O GAGE 20-26 RED TIP A TIP F .023 16-20 BLUE TIP B TIP E .036 12-16 YELLOW TIP C TIP D .047 REQUIREMENTS AS SPECIFIED HEREIN AND IN AS22520 FOR TYPE 2 TOOLS: 1. DIMENSIONS UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN INCHES AS SPECIFIED IN FIGURE 1 AND 2. CONFIGURATION IS OPTIONAL WITHIN DEFINED OR

10、 MAXIMUM DIMENSIONS IN THE CLOSE HANDLE POSITION. TOLERANCES ARE DECIMALS .010 INCHES AND ANGLES .5 DEGREES. 2. MATERIAL AND FINISH JAW SHALL BE 50 POINT CARBON MINIMUM ALLOY STEEL HEAT TREAT ROCKWELL C 43-54 WITH BLACK OXIDE FINISH. CONVEX CRIMP SURFACES SHALL BE POLISHED TO A SURFACE FINISH OF 16

11、9 (RMS) MICROFINISH. HANDLES SHALL BE STEEL WITH COMMERCIAL GRADE NICKEL OR CHROME PLATING. LOCATOR SHALL BE S 40 POINT CARBON STEEL MINIMUM WITH BLACK OXIDE FINISH. GRIPS SHALL BE PLASTIC OR RUBBER (COLOR OPTIONAL). 3. MAXIMUM WEIGHT 1.0 POUNDS 4. IDENTIFICATION MARKING MANUFACTURERS NAME OR AIR135

12、1 LISTED LOGO, MANUFACTURER PART NUMBER, AND SPECIFICATION PART NUMBER (M22520/37-01) SHALL BE PERMANENTLY MARKED ON THE TOOL AND LEGIBLE AFTER ALL AS22520 ENVIRONMENTAL EXPOSURES. 5. TOOL DESIGN CYCLE CONTROL (RATCHET) ADJUSTMENT DEVICE SHALL BE SET TO RELEASE BETWEEN 40 TO 50 POUNDS AND SHALL BE T

13、AMPER PROOF. TOOL SHALL BE INSPECTED WITH THE INSPECTION GAGES SPECIFIED IN TABLE 1. 6. ASSEMBLY INSTRUCTIONS EACH TOOL SHALL HAVE AN INSTRUCTION SHEET WHICH INCLUDES CRIMPING AND GAGE APPLICATIONS, USAGE AND INSTRUCTIONS. 7. PART NUMBER M22520/37-01 8. APPLICATIONS TOOL IS USED TO CRIMP AS81824/1 S

14、PLICES ONLY. 9. SUPERSESSION INFORMATION THE M22520/37-01 IS AN ALL INCLUSIVE DIE TOOL THAT CAN USED IN PLACE OF THE M22520/5-102, /5-103, /10-103, AND /10-104 DIES, BUT THERE NO DIRECT SUPERSESSION. AS22520/37 SUPERSEDED MIL-C-22520/37 WITHOUT PART NUMBER CHANGE. SPECIFICATION NOTES: 1. A CHANGE BA

15、R (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.