SAE AS 15005C-2010 FITTING LUBRICATION HYDRAULIC THROAT OR SURFACE CHECK 1 8 PIPE THREADS NICKEL-COPPER ALLOY TYPE V《V型、镍-铜合金、1 8管螺纹、入口或表明检查、液压润滑配件》.pdf

《SAE AS 15005C-2010 FITTING LUBRICATION HYDRAULIC THROAT OR SURFACE CHECK 1 8 PIPE THREADS NICKEL-COPPER ALLOY TYPE V《V型、镍-铜合金、1 8管螺纹、入口或表明检查、液压润滑配件》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 15005C-2010 FITTING LUBRICATION HYDRAULIC THROAT OR SURFACE CHECK 1 8 PIPE THREADS NICKEL-COPPER ALLOY TYPE V《V型、镍-铜合金、1 8管螺纹、入口或表明检查、液压润滑配件》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARD FITTING, LUBRICATION, HYDRAULIC, THROAT OR SURFACE CHECK, 1/8 PIPE THREADS, NICKEL-COPPER ALLOY, TYPE VAS15005Copyright 2010 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any mea

2、ns, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org I

3、SSUED 2001-05REVISED 2010-03THIRD ANGLE PROJECTION CUSTODIAN: SAE G-3/G-3B REV.CFEDERAL SUPPLY CLASS 4730 AS15005SHEET 1 OF 3REV. CPROCUREMENT SPECIFICATION: /3/, /5/ AS35411SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering

4、 sciences. Theuse ofthis report is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirmed, revis

5、ed, orcancelled. SAE invites yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS15005CRATIONALE REVISE AS15005 TO UPDATE TABLE 1 BY REMOVING THE WEIGHT OF STEEL COLUMN AND TO INCOPORATE OTHER ED

6、ITORIAL CHANGES FIGURE 1 - FITTING, STRAIGHT FIGURE 2 - FITTING, ELBOW INACTIVE IN PART - SEE NOTE /17/ Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS15005SHEET 2 OF 3REV. CFIT

7、TING, LUBRICATION, HYDRAULIC, THROAT OR SURFACE CHECK, 1/8 PIPE THREADS, NICKEL-COPPER ALLOY, TYPE VBODY CONTOURSOPTIONAL WITHMANUFACTURERSF.037 MAX x 455DBACTHREAD T/9/NOTCHED FOR IDENTIFICATION/8/FIGURE 3 - FITTING, ELBOW, 90 TABLE 1 - DIMENSIONS PARTNUMBER /15/ FIG. THREAD T /6/A.031 B/7/CMAXDMAX

8、E.003 F5 G.062 AS15005-1 AS15005-2 AS15005-3 AS15005-4 AS15005-5 AS15005-6 1123331/8-27 1/8-27 1/8-27 1/8-27 1/8-27 1/8-27 .312.312.312.312.312.312.1875 .1875 .1875 .1875 .1875 .1875 .375.625.625.5621.250 1.094 1.063 1.312 .438.438.438.438.438.43830 65 90 105 .750 1.125 NOTES: 1. MATERIAL: NICKEL-CO

9、PPER ALLOY. SEE PROCUREMENT SPECIFICATION. 2. HEAT TREATMENT: NONE. 3. FINISH: BRIGHT DIPPED. SEE PROCUREMENT SPECIFICATION. 4. IDENTIFICATION: MARK PER AS478 METHOD 35D MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, AND PART NUMBER. /5/ PROCUREMENT SPECIFICATION: AS35411 EXCEPT AS SPECIFIED ON THIS ST

10、ANDARD. THE DRAWING AND ALL THE SPECIFIED DOCUMENTS DEFINE THE REQUIREMENTS FOR THE END PRODUCT. ALL THE REQUIREMENTS MUST BE MET IN ORDER TO IDENTIFY THE ITEM WITH THAT PART NUMBER. USERS OF THIS STANDARD ARE ADVISED TO CONTROL SOURCE APPROVAL BY STANDARD PAGE SUPPLEMENT OR SIMILAR MEANS. /6/ PIPE

11、THREAD SHALL BE MODIFIED (DRYSEAL) TAPER PIPE THREAD, NPTF, IN ACCORDANCE WITH FED-STD-H28/8, SCREW THREAD STANDARDS FOR FEDERAL SERVICES, EXCEPT THAT LENGTH OF EFFECTIVE THREAD L2 IS SHORTENED BY ONE THREAD ON SMALL END AND ONE THREAD ON LARGE END. SMALL END OF THREAD SHALL GAGE FROM FLUSH TO MINUS

12、 ONE AND ONE-HALF TURNS FROM SMALL END OF DRYSEAL (NPTF-L1) THIN RING GAGE. WIDTH OF FLAT ON THREAD CREST MAY BE .007 MAXIMUM. PIPE THREAD SHALL BE PTF-SPL SHORT FOR ALL DASH NUMBERS EXCEPT -1 SHALL BE PTF-SPL EXTRA SHORT, IN ACCORDANCE WITH SAE J475. /7/ MINIMUM EFFECTIVE THREAD LENGTH. /8/ SURFACE

13、 OR THROAT CHECK VALVE IS OPTIONAL. /9/ FITTING END IN ACCORDANCE WITH AS15000, STYLE OPTIONAL. 10. INTENDED USE: THIS PART IS INTENDED FOR USE IN LUBRICATING CONNECTIONS AT PRESSURES TO 6000 psi. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or netw

14、orking permitted without license from IHS-,-,-AEROSPACE STANDARD AS15005SHEET 3 OF 3REV. CFITTING, LUBRICATION, HYDRAULIC, THROAT OR SURFACE CHECK, 1/8 PIPE THREADS, NICKEL-COPPER ALLOY, TYPE V11. THIS STANDARD IS A CONVERSION OF MILITARY STANDARD MS15005, FITTINGS, LUBRICATION (HYDRAULIC) THROAT OR

15、 SURFACE, CHECK, 1/8 PIPE THREADS, NICKEL-COPPER ALLOY, TYPE V, AND IS NOT A WORD-FOR-WORD CONVERSION. 12. INTERPRETATION OF DRAWING PER ARP4296. 13. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 in Ra. SURFACES OF HEX

16、 FLATS MAY BE 250 in Ra. 14. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. 15. DIMENSIONS ARE IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .010, ANGULAR DIMENSIONS 0 DEGREES 30. 16. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. /17/ SIZE AS15005-6 IS INACTIVE FOR NEW

17、 DESIGN, SIZE AS15005-5 MAY BE USED INSTEAD. /18/ EXAMPLE OF PART NUMBER: AS15005 -1 BASIC PART NUMBER SIZE 19. THIS SPECIFICATION HAS INTERNATIONAL STANDARDIZATION AGREEMENT. SEE AS35411. 20. A CHANGE BAR (|) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECH

18、NICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. 21. INVENTORIED PARTS CONFORMING TO THE PREVIOUS LETTER CHANGE MAY BE USED TO DEPLETION. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-