SAE AS 15001C-2010 FITTING LUBRICATION HYDRAULIC SURFACE CHECK 250-28 TAPER THREADS STEEL TYPE I《I型钢锥螺纹 250-28表面裂纹液压润滑配件》.pdf

《SAE AS 15001C-2010 FITTING LUBRICATION HYDRAULIC SURFACE CHECK 250-28 TAPER THREADS STEEL TYPE I《I型钢锥螺纹 250-28表面裂纹液压润滑配件》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 15001C-2010 FITTING LUBRICATION HYDRAULIC SURFACE CHECK 250-28 TAPER THREADS STEEL TYPE I《I型钢锥螺纹 250-28表面裂纹液压润滑配件》.pdf（3页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARD FITTING, LUBRICATION, HYDRAULIC, SURFACE CHECK,.250-28 TAPER THREADS, STEEL, TYPE IAS15001Copyright 2010 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mech

2、anical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 2001-05REVISED

3、 2010-03THIRD ANGLE PROJECTION CUSTODIAN: SAE G-3/G-3B REV.CFEDERAL SUPPLY CLASS 4730 AS15001SHEET 1 OF 3REV. CPROCUREMENT SPECIFICATION: /5/ AS35411SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis

4、report is entirely voluntary, andits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirmed, revised, orcancelled. SAE invi

5、tes yourwrittencomments andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS15001CRATIONALE REVISE AS15001 TO UPDATE TABLE 1 BY REMOVING THE WEIGHT OF STEEL COLUMN, REMOVE A DASH FROM BETWEEN SIZE AND FINISH IN THE

6、PART NUMBER, AND TO INCOPORATE OTHER EDITORIAL CHANGES FIGURE 1 - FITTING, STRAIGHT FIGURE 2 - FITTING, ELBOW Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS15001SHEET 2 OF 3REV

7、. CFITTING, LUBRICATION, HYDRAULIC, SURFACE CHECK, .250-28 TAPER THREADS, STEEL, TYPE IFIGURE 3 - FITTING, ELBOW 90 TABLE 1 - DIMENSIONS PARTNUMBER /15/ FIG. THREAD T PER FED-STD-H28/2, /18/ A.031 B/6/CMAX.D.062 E.003 F5 AS15001-1 1 .250-28 UNS-2A .187 .1094 .500 .312 AS15001-2 1 .250-28 UNS-2A .625

8、 .2031 .937 .312 AS15001-3 2 .250-28 UNS-2A .187 .1094 .406 .812 .375 45 AS15001-4 3 .250-28 UNS-2A .187 .1094 .531 .781 .375 90 NOTES: NOTICE THIS DOCUMENT REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. 1. MATER

9、IALS: STEEL. SEE PROCUREMENT SPECIFICATION. 2. HEAT TREATMENT: SEE PROCUREMENT SPECIFICATION FOR HARDNESS REQUIREMENTS. /3/ FINISH: a. CODE LETTER C - CADMIUM PLATE, SEE PROCUREMENT SPECIFICATION. b. CODE LETTER P - ZINC PLATE, SEE PROCUREMENT SPECIFICATION. c. CODE LETTER U - ZINC-NICKEL PLATE, SEE

10、 PROCUREMENT SPECIFICATION. 4. IDENTIFICATION: MARK PER AS478 METHOD 35D MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, AND PART NUMBER. /5/ PROCUREMENT SPECIFICATION: AS35411 EXCEPT AS SPECIFIED ON THIS STANDARD. THE DRAWING AND ALL THE SPECIFIED DOCUMENTS DEFINE THE REQUIREMENTS FOR THE END PRODUCT.

11、ALL THE REQUIREMENTS MUST BE MET IN ORDER TO IDENTIFY THE ITEM WITH THAT PART NUMBER. USERS OF THIS STANDARD ARE ADVISED TO CONTROL SOURCE APPROVAL BY STANDARD PAGE SUPPLEMENT OR SIMILAR MEANS. /6/ MINIMUM EFFECTIVE THREAD LENGTH. /7/ FITTING END IN ACCORDANCE WITH AS15000, STYLE OPTIONAL. 8. INTEND

12、ED USE: THIS PART IS INTENDED FOR USE IN LUBRICATING CONNECTIONS AT PRESSURES TO 8000 psi. 9. THIS STANDARD IS A CONVERSION OF MILITARY STANDARD MS15001, FITTINGS, LUBRICATION (HYDRAULIC) SURFACE CHECK, .1/4-28 TAPER THREADS, STEEL, TYPE I, AND IS NOT A WORD-FOR-WORD CONVERSION. Copyright SAE Intern

13、ational Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS15001SHEET 3 OF 3REV. CFITTING, LUBRICATION, HYDRAULIC, SURFACE CHECK, .250-28 TAPER THREADS, STEEL, TYPE I10. INTERPRETATION OF DRAWING PER ARP4296.

14、11. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MACHINED SURFACES TO BE 125 in Ra. SURFACES OF HEX FLATS MAY BE 250 in Ra. 12. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 13. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. 14. DIMENSIO

15、NS ARE IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .010, ANGULAR DIMENSIONS 0 DEGREES 30. /15/ EXAMPLE OF PART NUMBER: AS15001 -1 P BASIC PART NUMBER SIZE FINISH 16. THIS SPECIFICATION HAS INTERNATIONAL STANDARDIZATION AGREEMENT. SEE AS35411. 17. A CHANGE BAR (|) LOCATED IN

16、THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS.

17、CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. /18/ 1/4 - 28 UNIFIED NATIONAL FORM OF THREAD WITH 3/4 in DIAMETER TAPER PER FOOT. BASIC PITCH DIAMETER AT SMALL END OF THREAD EQUALS .2224 TO .2257. FITTINGS SHALL BE SUITABLE FOR INSTALLATION TIGHTLY INTO 1/4 - 28 UNF - 3B THREADED HOLE. 19. INVENTORIED PARTS CONFORMING TO THE PREVIOUS LETTER CHANGE MAY BE USED TO DEPLETION. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-