SAE AS 1007H-2010 FITTING UNION STANDARD AND REDUCER BULKHEAD FLARELESS《标准和缩减舱壁非扩口联合配件》.pdf

《SAE AS 1007H-2010 FITTING UNION STANDARD AND REDUCER BULKHEAD FLARELESS《标准和缩减舱壁非扩口联合配件》.pdf》由会员分享，可在线阅读，更多相关《SAE AS 1007H-2010 FITTING UNION STANDARD AND REDUCER BULKHEAD FLARELESS《标准和缩减舱壁非扩口联合配件》.pdf（6页珍藏版）》请在麦多课文档分享上搜索。

1、AEROSPACE STANDARD FITTING, UNION, STANDARD AND REDUCER, BULKHEAD, FLARELESS AS1007Copyright 2010 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, reco

2、rding, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1966-03REVISED 2010-07THIRD ANGLE PROJEC

3、TION CUSTODIAN: G-3/G-3B REV.HFEDERAL SUPPLY CLASS 4730 AS1007SHEET 1 OF 7REV. HPROCUREMENT SPECIFICATION: /4/ AS18280SAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirely voluntary, a

4、ndits applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay bereaffirmed, revised, orcancelled. SAE invites yourwrittencomments andsugg

5、estions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS1007HRATIONALE ERROR CORRECTION UNDER /19/ PART NUMBER. CLARIFICATION NOTE /21/ ADDED FIGURE 1 - FITTING, UNION, STANDARD AND REDUCER, BULKHEAD END FOR OPTIONAL USE IN PO

6、RT INSTALLATION, NON-REDUCER SHOWN INACTIVE /20/ Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS1007SHEET 2 OF 6REV. HFITTING, UNION, STANDARD AND REDUCER, BULKHEAD, FLARELESS F

7、IGURE 2 - FITTING, UNION, STANDARD AND REDUCER, BULKHEAD END NOT FOR USE IN PORT INSTALLATION, NON-REDUCER SHOWN, SAME AS FIGURE 1 EXCEPT AS SHOWN TABLE 1 - OVERALL LENGTH A /12/ SIZE SIZE OF PORT #1 OF PORT 02 03 04 05 06 08 10 12 14 16 20 24 32 #2 .010 .010 .010 .010 .010 .010 .010 .010 .010 .010

8、.010 .010 .010 02 1.484 1.516 1.578 1.609 1.703 1.844 2.000 2.156 2.156 2.156 2.156 2.156 2.422 03 1.516 1.563 1.625 1.656 1.750 1.891 2.047 2.203 2.203 2.203 2.203 2.203 2.469 04 1.547 1.594 1.656 1.688 1.781 1.922 2.078 2.234 2.234 2.234 2.234 2.234 2.500 05 1.578 1.625 1.688 1.688 1.781 1.922 2.0

9、78 2.324 2.234 2.234 2.234 2.234 2.500 06 1.641 1.688 1.750 1.750 1.797 1.938 2.094 2.250 2.250 2.250 2.250 2.250 2.516 08 1.734 1.781 1.844 1.844 1.891 2.031 2.188 2.344 2.344 2.344 2.344 2.344 2.609 10 1.813 1.859 1.922 1.922 1.969 2.109 2.250 2.406 2.406 2.406 2.406 2.406 2.672 12 1.922 1.969 2.0

10、31 2.031 2.078 2.219 2.360 2.484 2.469 2.469 2.469 2.469 2.734 14 1.922 1.969 2.031 2.031 2.078 2.219 2.360 2.469 2.469 2.469 2.469 2.469 2.734 16 1.922 1.969 2.031 2.031 2.078 2.219 2.360 2.469 2.469 2.469 2.469 2.469 2.734 20 1.922 1.969 2.031 2.031 2.078 2.219 2.360 2.469 2.469 2.469 2.469 2.469

11、2.734 24 1.922 1.969 2.031 2.031 2.078 2.219 2.360 2.469 2.469 2.469 2.469 2.469 2.734 32 1.984 2.031 2.094 2.094 2.141 2.281 2.422 2.531 2.531 2.531 2.531 2.531 2.734 PORT #1 FITTING END PER AS4377 STYLE H IF SAME SIZE OR SMALLER THAN PORT #2 ID THRU IF LARGER THAN PORT #2 ID Z DEEP Copyright SAE I

12、nternational Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS1007SHEET 3 OF 6REV. HFITTING, UNION, STANDARD AND REDUCER, BULKHEAD, FLARELESS TABLE 2 - HOLE DEPTH Y /12/ SIZE SIZE OF PORT #1 OFPORT#2 02 03 0

13、4 05 06 08 10 12 14 16 20 24 32 02 - - - - - - - - - - - - - 03 .469 - - - - - - - - - - - - 04 .484 .484 - - - - - - - - - - - 05 .500 .500 .516 - - - - - - - - - - 06 .547 .531 .562 .562 - - - - - - - - - 08 .594 .594 .625 .625 .641 - - - - - - - - 10 .656 .656 .672 .672 .703 .672 - - - - - - - 12

14、 .719 .719 .734 .750 .766 .750 .750 - - - - - - 14 .688 .688 .704 .719 .735 .719 .719 .861 - - - - - 16 .656 .656 .672 .672 .703 .688 .688 .719 .688 - - - - 20 .594 .594 .609 .609 .641 .625 .625 .656 .625 .703 - - - 24 .516 .516 .531 .547 .562 .641 .656 .578 .547 .641 .656 - - 32 .453 .438 .469 .469

15、 .469 .469 .469 .516 .485 .562 .578 .656 - TABLE 3 - HOLE DEPTH Z /12/ SIZE SIZE OF PORT #1 OF PRT #2 02 03 04 05 06 08 10 12 14 16 20 24 32 02 - 1.016 1.062 1.078 1.156 1.250 1.391 1.500 1.477 1.438 1.375 1.297 1.438 03 - - 1.047 1.078 1.141 1.250 1.391 1.500 1.471 1.422 1.375 1.297 1.422 04 - - -

16、1.094 1.172 1.281 1.406 1.516 1.494 1.453 1.391 1.312 1.453 05 - - - - 1.172 1.281 1.422 1.531 1.500 1.453 1.391 1.328 1.453 06 - - - - - 1.297 1.438 1.547 1.523 1.391 1.422 1.344 1.484 08 - - - - - - 1.453 1.562 1.533 1.484 1.438 1.359 1.391 10 - - - - - - - 1.562 1.537 1.500 1.438 1.359 1.500 12 -

17、 - - - - - - - 1.574 1.531 1.468 1.406 1.531 14 - - - - - - - - - 1.566 1.503 1.430 1.559 16 - - - - - - - - - - 1.516 1.453 1.562 20 - - - - - - - - - - - 1.468 1.59424 - - - - - - - - - - - - - 32 - - - - - - - - - - - - - Copyright SAE International Provided by IHS under license with SAENot for R

18、esaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS1007SHEET 4 OF 6REV. HFITTING, UNION, STANDARD AND REDUCER, BULKHEAD, FLARELESS TABLE 4 - TUBE SIZE AND CORRESPONDING THREAD PORT SIZE(NOMINAL TUBE SIZE)T THREAD PER AS8879 CLASS 3A 02 .125 .3125-24 UNJF 0

19、3 .188 .3750-24 UNJF 04 .250 .4375-20 UNJF 05 .312 .5000-20 UNJF 06 .375 .5625-18 UNJF 08 .500 .7500-16 UNJF 10 .625 .8750-14 UNJF 12 .750 1.0625-12 UNJ 14 .875 1.1875-12 UNJ 16 1.000 1.3125-12 UNJ 20 1.250 1.6250-12 UNJ24 1.500 1.8750-12 UNJ 32 2.000 2.5000-12 UNJ TABLE 5 - HEX DIMENSION AND WEIGHT

20、S /11/ BASIC NO. AS1007/19/LARGEST PORT SIZE CODE B.010 H LB/EAAPPROX REF ALUMLB/EAAPPROX REF STEELLB/EAAPPROX REF TI02 .542 .552- .565 .00990 .0279 .0153 03 .605 .615- .628 .0162 .0432 .0243 04 .668 .678- .691 .0207 .0558 .0315 05 .730 .740- .753 .0261 .0702 .0405 06 .792 .802- .815 .0315 .0855 .04

21、86 08 .980 .990-1.003 .0576 .158 .0900 10 1.103 1.113-1.128 .0810 .210 .126 12 1.353 1.363-1.380 .120 .325 .187 14 1.478 1.488-1.505 - - - 16 1.603 1.613-1.630 .182 .437 .286 20 1.853 1.863-1.880 .224 .610 .332 24 2.099 2.109-2.225 .266 .733 .422 32 2.724 2.734-2.760 - - - NOTES: NOTICE THIS DOCUMEN

22、T REFERENCES A PART WHICH CONTAINS CADMIUM AS A PLATING MATERIAL. CONSULT LOCAL OFFICIALS IF YOU HAVE QUESTIONS CONCERNING CADMIUMS USE. /1/ MATERIAL: a. CODE LETTER DASH (-) - TYPE 4130 LOW ALLOY STEEL BAR PER AMS6370 OR AMS-S-6758 EXCEPT HEAT TREATMENT PER PROCUREMENT SPECIFICATION. /2/ b. CODE LE

23、TTER D - TYPE 2024-T6 OR -T851 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/6. /2/ c. CODE LETTER J - TYPE 304 CORROSION RESISTANT STEEL BAR PER AMS5639 OR AMS-QQ-S-763 EXCEPT HARDNESS PER PROCUREMENT SPECIFICATION. /2/ d. CODE LETTER K - TYPE 316 CORROSION RESISTANT STEEL BAR PER AMS5648 OR AMS-QQ-S-763 EXC

24、EPT HARDNESS PER PROCUREMENT SPECIFICATION. /2/ Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS1007SHEET 5 OF 6REV. HFITTING, UNION, STANDARD AND REDUCER, BULKHEAD, FLARELESS e.

25、 CODE LETTER R - TYPE 321 CORROSION RESISTANT STEEL BAR PER AMS5645 OR AMS-QQ-S-763 EXCEPT HARDNESS PER PROCUREMENT SPECIFICATION. /2/ f. CODE LETTER S - TYPE 347 CORROSION RESISTANT STEEL BAR PER AMS5646 OR AMS-QQ-S-763 EXCEPT HARDNESS PER PROCUREMENT SPECIFICATION. /2/ g. CODE LETTER T - TYPE 6AL-

26、4V TITANIUM ALLOY BAR PER AMS4928. h. CODE LETTER W - TYPE 7075-T73 ALUMINUM ALLOY BAR PER AMS4124; OR 7075-T73 ALUMINUM ALLOY BAR PER AMS-QQ-A-225/9. /2/ /2/ HEAT TREATMENT: a. CODE LETTER (-) - HARDNESS SHALL BE 92 HRB TO 40 HRC PER PROCUREMENT SPECIFICATION. b. MATERIAL CODE LETTERS D AND W - ELE

27、CTRICAL CONDUCTIVITY AND HARDNESS PER PROCUREMENT SPECIFICATION. c. MATERIAL CODE LETTERS J, K, R AND S - HARDNESS SHALL BE 80 HRB MINIMUM PER PROCUREMENT SPECIFICATION. d. OTHER MATERIAL CODES - NONE. 3. FINISH: a. CODE LETTER (-) - CADMIUM PLATE PER AMS-QQ-P-416, TYPE II, CLASS 2. b. MATERIAL CODE

28、 LETTER D - ANODIZE PER AMS2472 OR MIL-A-8625, TYPE II, CLASS 2, DYE GREEN SIMILAR TO COLOR 14187 OF FED-STD-595. c. MATERIAL CODE LETTERS J, K, R AND S - PASSIVATE PER AMS2700 TYPE 6 OR 7. d. MATERIAL CODE LETTER T - FLUORIDE PHOSPHATE CONVERSION COAT PER AMS2486 OR ANODIZE PER AMS2488, TYPE 2. e.

29、MATERIAL CODE LETTER W - ANODIZE PER AMS2472 OR MIL-A-8625, TYPE II, CLASS 2, DYE BROWN SIMILAR TO COLOR 10080 OF FED-STD-595. /4/ PROCUREMENT SPECIFICATION: AS18280 EXCEPT AS SPECIFIED ON THIS STANDARD. PRODUCT SUPPLIED TO THIS SPECIFICATION SHALL BE MANUFACTURED BY AN ACCREDITED MANUFACTURER AS LI

30、STED IN THE PERFORMANCE REVIEW INSTITUTE (PRI) QUALIFIED PRODUCTS LIST (QPL) PRI-QPL-AS18280 FOR THIS STANDARD. SEE http:/ FOR CURRENT QPL ONLINE. /5/ IDENTIFICATION AT LOCATION SHOWN: MARK PER AS478 CLASS C OR D OR METHOD 7A3, 15A3, OR 15B. a. FOR SIZE 06 AND SMALLER MANUFACTURERS NAME, CAGE CODE O

31、R TRADEMARK, LETTERS “AS” AND MATERIAL CODE LETTER. b. FOR SIZE 08 AND LARGER, MANUFACTURERS NAME, CAGE CODE OR TRADEMARK, BASIC PART NUMBER AND MATERIAL CODE LETTER. 6. INVENTORIED PARTS CONFORMING TO THE PREVIOUS ISSUE MAY BE USED TO DEPLETION. 7. INTENDED USE: THIS PART IS DESIGNED FOR USE IN TUB

32、ING CONNECTION SYSTEMS WITH NOMINAL OPERATING PRESSURES AS FOLLOWS: a. SIZES 02 THROUGH 16 IN LOW ALLOY STEEL, CORROSION RESISTANT STEEL AND TITANIUM ALLOY AT 3000 psi. b. SIZES 02 THROUGH 10 IN ALUMINUM ALLOY AND SIZE 20 IN ALL MATERIALS AT 1500 psi. c. SIZES 12 THROUGH 16 IN ALUMINUM ALLOY AT 900

33、psi. d. SIZE 20 IN ALUMINUM ALLOY AT 600 psi. Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-AEROSPACE STANDARD AS1007SHEET 6 OF 6REV. HFITTING, UNION, STANDARD AND REDUCER, BULKHEAD, FLARELESS /8/

34、THE HEX CORNERS MAY BE ROUNDED PER ARP1942. 9. FOR REDUCER CONFIGURATIONS, THE PRESSURE RATING IS DETERMINED BY THE LARGEST PORT. 10. THE NON-REDUCER CONFIGURATION WITHOUT A SUFFIX PART NUMBER CODE IS THE FUNCTIONAL EQUIVALENT OF AS21924 FOR THE CORRESPONDING SIZE AND IS INTENDED TO BE SUITABLE AS A

35、 REPLACEMENT STANDARD. /11/ WEIGHTS ARE FOR NON-REDUCERS ONLY. REDUCER FITTINGS WILL HAVE LOWER WEIGHTS. /12/ REDUCER FITTINGS WHICH FALL IN THE SHADED AREA OF TABLES 1, 2, AND 3 SHOULD BE AVOIDED. IF THEY MUST BE USED, SPECIAL ATTENTION SHOULD BE GIVEN TO CLAMPING OR OTHER MEANS TO PROTECT THE SMAL

36、LER PORT OR TUBE. 13. A CHANGE BAR (|) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION

37、 OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY. 14. INTERPRETATION OF DRAWING PER ARP4296. 15. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M; REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPE

38、CIFIED, MACHINED SURFACES TO BE 125 in Ra. FORGED SURFACES MAY BE 250 in Ra. 16. BREAK ALL SHARP EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 17. DIMENSIONING AND TOLERANCING: ASME Y14.5M-1994. 18. DIMENSIONING IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .016, ANGULAR DIME

39、NSIONS 0 DEGREES 30. /19/ EXAMPLE OF PART NUMBER: AS1007 H J 10 10PART NUMBER AS1007HJ0808 DESIGNATES A 304 CRES FITTING WITH SIZE 08 PORTS AND A STYLE H BULKHEAD END. PART NUMBER AS1007J0808 DESIGNATES A 304 CRES FITTING WITH SIZE 08 PORTS AND A STYLE S BULKHEAD END. PART NUMBER AS1007H-0808 DESIGN

40、ATES A 4130 LOW ALLOY STEEL FITTING WITH SIZE 08 PORTS AND A STYLE H BULKHEAD END. PART NUMBER AS1007-0808 DESIGNATES A 4130 LOW ALLOY STEEL FITTING WITH SIZE 08 PORTS AND A STYLE S BULKHEAD END. 20. THIS STANDARD IS INACTIVE FOR NEW DESIGN AS OF 2010-08. USE AS6047 FOR NEW DESIGN. /21/ FITTINGS WIT

41、H AS4377 STYLE “H” ENDS MAY BE DESIGNATED WITH THE SUFFIX “H“ AFTER THE PART NUMBER AND CANNOT BE USED IN PORTS. FITTINGS WITH AS4377 STYLE S ENDS MAY BE ASSEMBLED INTO INTERNALLY THREADED PORTS BUT ARE NOT RECOMMENDED FOR THIS APPLICATION. FITTINGS WITH AS4377 STYLE S ENDS ARE HISTORICALLY UNRELIAB

42、LE WHEN INSTALLED IN PORTS BUT HAVE BEEN USED SUCCESSFULLY IN APPLICATIONS WITH PRESSURES LIMITED TO 1500 PSI. BASIC NUMBERSUFFIX CODE “H” FOLLOWING BASIC PART NUMBER, ONLY FOR PARTS WITH AS4377 STYLE H FITTING END /21/ SIZE CODE, TUBE SIZE OF PORT #2 IN .062 INCREMENTSSIZE CODE, TUBE SIZE OF PORT #1 IN .062 INCREMENTSMATERIAL CODE LETTER /1/Copyright SAE International Provided by IHS under license with SAENot for ResaleNo reproduction or networking permitted without license from IHS-,-,-