SAE AMS 5854C-2015 Nickel Alloy Corrosion and Heat-Resistant Bars Wire Forgings and Rings 61Ni - 20 5Cr - 8 5Mo - 3 4Cb(Nb) - 1 3Ti - 5 0Fe Consumable Electrode or Vacuum Induction.pdf
《SAE AMS 5854C-2015 Nickel Alloy Corrosion and Heat-Resistant Bars Wire Forgings and Rings 61Ni - 20 5Cr - 8 5Mo - 3 4Cb(Nb) - 1 3Ti - 5 0Fe Consumable Electrode or Vacuum Induction.pdf》由会员分享,可在线阅读,更多相关《SAE AMS 5854C-2015 Nickel Alloy Corrosion and Heat-Resistant Bars Wire Forgings and Rings 61Ni - 20 5Cr - 8 5Mo - 3 4Cb(Nb) - 1 3Ti - 5 0Fe Consumable Electrode or Vacuum Induction.pdf(7页珍藏版)》请在麦多课文档分享上搜索。
1、_SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising theref
2、rom, is the sole responsibility of the user.”SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions.Copyright 2015 SAE InternationalAll rights reserved. No part of this publi
3、cation may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE.TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada)Tel: +1 724-776-4970 (out
4、side USA)Fax: 724-776-0790Email: CustomerServicesae.orgSAE WEB ADDRESS: http:/www.sae.orgSAE values your input. To provide feedbackon this Technical Report, please visithttp:/www.sae.org/technical/standards/AMS5854CAEROSPACEMATERIAL SPECIFICATIONAMS5854 REV. CIssued 1991-01Reaffirmed 2006-04Revised
5、2015-12Superseding AMS5854BNickel Alloy, Corrosion and Heat-Resistant, Bars, Wire, Forgings, and Rings61Ni -20.5Cr -8.5Mo -3.4Cb(Nb) -1.3Ti -5.0FeConsumable Electrode or Vacuum Induction MeltedSolution Heat Treated(Composition similar to UNS N07716)RATIONALEAMS5854C revises Condition (3.3.2), Proper
6、ties (3.5.1.2.3) and Reports (4.4), and is a Five Year Review and update of this specification.1. SCOPE1.1 FormThis specification covers a corrosion and heat-resistant nickel alloy in the form of bars, wire, forgings, flash welded rings, and extrusions 4 inches (102 mm) and under in nominal diameter
7、 or least distance between parallel sides, and stock for forging or flash welded rings.1.2 ApplicationThese products have been used typically for parts requiring both corrosion and oxidation resistance up to 1,000 F (538 C), and where such parts may require welding during fabrication and are then pr
8、ecipitation heat treated to develop required properties, but usage is not limited to such applications.2. APPLICABLE DOCUMENTSThe issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supplier may work to a
9、 subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply.2.1 SAE PublicationsAvailable from SAE International, 400 Commonweal
10、th Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or +1 724-776-4970 (outside USA), www.sae.org.AMS2261 Tolerances, Nickel, Nickel Alloy, and Cobalt Alloy Bars, Rods, and WireAMS2269 Chemical Check Analysis Limits, Nickel, Nickel Alloys, and Cobalt AlloysSAE INTERNATIONA
11、L AMS5854C Page 2 of 7AMS2371 Quality Assurance Sampling and Testing, Corrosion and Heat-Resistant Steels and Alloys, Wrought Products and Forging StockAMS2374 Quality Assurance Sampling and Testing, Corrosion and Heat-Resistant Steel and Alloy ForgingsAMS2750 PyrometryAMS2806 Identification Bars, W
12、ire, Mechanical Tubing, and Extrusions, Carbon and Alloy Steels and Corrosion and Heat-Resistant Steels and AlloysAMS2808 Identification ForgingsAMS7490 Rings, Flash Welded, Corrosion and Heat-Resistant Austenitic Steels, Austenitic-Type Iron, Nickel, or Cobalt Alloys, or Precipitation-Hardenable Al
13、loys2.2 ASTM PublicationsAvailable from ASTM International, 100 Barr Harbor Drive, P.O. Box C700, West Conshohocken, PA 19428-2959, Tel: 610-832-9585, www.astm.org.ASTM E8/E8M Tension Testing of Metallic MaterialsASTM E10 Brinell Hardness of Metallic MaterialsASTM E18 Rockwell Hardness of Metallic M
14、aterialsASTM E112 Determining Average Grain SizeASTM E354 Chemical Analysis of High-Temperature, Electrical, Magnetic, and Other Similar Iron, Nickel, and Cobalt Alloys3. TECHNICAL REQUIREMENTS3.1 CompositionShall conform to the percentages by weight shown in Table 1, determined by wet chemical meth
15、ods in accordance with ASTM E354, by spectrochemical methods, or by other analytical methods acceptable to purchaser. Table 1 - CompositionElement min maxCarbonManganeseSiliconPhosphorusSulfurChromiumNickelMolybdenumColumbium (Niobium)TitaniumCobaltAluminumIron-19.0059.007.502.751.00-remainder0.030.
16、200.200.0150.01022.0063.009.504.001.601.000.35SAE INTERNATIONAL AMS5854C Page 3 of 73.1.1 Check AnalysisComposition variations shall meet the applicable requirements of AMS2269.3.2 Melting PracticeAlloy shall be produced by multiple melting using consumable electrode practice in the remelt cycle or
17、shall be induction melted under vacuum.3.3 ConditionThe product shall be supplied in the following condition:3.3.1 BarsHot finished and solution heat treated; round bars shall be ground or turned.3.3.2 Bars shall not be cut from plate (see 4.4.2).3.3.3 WireCold drawn and solution heat treated.3.3.4
18、Forgings, Extrusions, and Flash Welded RingsSolution heat treated.3.3.4.1 Flash welded rings shall not be supplied unless specified or permitted on purchasers part drawing. When supplied, rings shall be manufactured in accordance with AMS7490.3.3.5 Stock for Forging or Flash Welded RingsAs ordered b
19、y the forging or flash welded ring manufacturer.3.4 Heat TreatmentBars, forgings, and flash welded rings shall be solution heat treated by heating to a temperature within the range 1,850 to 1,950 F (1,010 to 1,066 C), holding at the selected temperature within 25 F (14 C) for a time commensurate wit
20、h cross-sectional thickness, and cooling at a rate equivalent to air cooling. Pyrometry shall be in accordance with AMS2750.3.5 PropertiesThe product shall conform to the following requirements:3.5.1 Bars, Wire, Forgings, and Flash Welded Rings3.5.1.1 As Solution Heat Treated3.5.1.1.1 Hardness of Ba
21、rs, Forgings, and Flash Welded RingsShall be not higher than 287 HB, or equivalent (see 8.2).3.5.1.1.2 Tensile Strength of WireShall be not higher than 135 ksi (931 MPa), determined in accordance with ASTM E8/E8M.SAE INTERNATIONAL AMS5854C Page 4 of 73.5.1.1.3 Average Grain SizeASTM No. 3 or finer,
22、determined in accordance with ASTM E112, for product with a least cross-section dimension under 2-1/2 inches (63.5 mm).3.5.1.2 After Precipitation Heat TreatmentProduct, 4 inches (102 mm) and under in nominal diameter or least distance between parallel sides, shall meet the requirements of 3.5.1.2.1
23、 and 3.5.1.2.2 after being precipitation heat treated by heating to a temperature within the range 1,325 to 1,375 F (718 to 746 C), holding at the selected temperature within 15 F (8 C) for not less than 8 hours, cooling at a rate of 100 F 15 F (55 C 8 C) degrees per hour to 1,150 F 15 F (621 C 8 C)
24、, holding at 1,150 F 15 F (621 C 8 C) for not less than 8 hours, and cooling at a rate equivalent to air cooling. Instead of the 100 F (55 C) degrees per hour cooling rate to 1,150 F 15 F (621 C 8 C), product may be furnace cooled at any rate provided the time at 1,150 F 15 F (621 C 8 C) is adjusted
- 1.请仔细阅读文档,确保文档完整性,对于不预览、不比对内容而直接下载带来的问题本站不予受理。
- 2.下载的文档,不会出现我们的网址水印。
- 3、该文档所得收入(下载+内容+预览)归上传者、原创作者;如果您是本文档原作者,请点此认领!既往收益都归您。
下载文档到电脑,查找使用更方便
10000 积分 0人已下载
下载 | 加入VIP,交流精品资源 |
- 配套讲稿:
如PPT文件的首页显示word图标,表示该PPT已包含配套word讲稿。双击word图标可打开word文档。
- 特殊限制:
部分文档作品中含有的国旗、国徽等图片,仅作为作品整体效果示例展示,禁止商用。设计者仅对作品中独创性部分享有著作权。
- 关 键 词:
- SAEAMS5854C2015NICKELALLOYCORROSIONANDHEATRESISTANTBARSWIREFORGINGSANDRINGS61NI205CR85MO34CBNB13TI50FECONSUMABLEELECTRODEORVACUUMINDUCTIONPDF

链接地址:http://www.mydoc123.com/p-1022238.html