SAE AMS 5839C-2015 Nickel Alloy Corrosion and Heat-Resistant Welding Wire 59Ni - 22Cr - 2 0Mo - 14W - 0 35Al (UNS N06231).pdf

《SAE AMS 5839C-2015 Nickel Alloy Corrosion and Heat-Resistant Welding Wire 59Ni - 22Cr - 2 0Mo - 14W - 0 35Al (UNS N06231).pdf》由会员分享，可在线阅读，更多相关《SAE AMS 5839C-2015 Nickel Alloy Corrosion and Heat-Resistant Welding Wire 59Ni - 22Cr - 2 0Mo - 14W - 0 35Al (UNS N06231).pdf（4页珍藏版）》请在麦多课文档分享上搜索。

1、_ SAE Technical Standards Board Rules provide that: “This report is published by SAE to advance the state of technical and engineering sciences. The use of this report is entirely voluntary, and its applicability and suitability for any particular use, including any patent infringement arising there

2、from, is the sole responsibility of the user.” SAE reviews each technical report at least every five years at which time it may be revised, reaffirmed, stabilized, or cancelled. SAE invites your written comments and suggestions. Copyright 2015 SAE International All rights reserved. No part of this p

3、ublication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-497

4、0 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org SAE values your input. To provide feedback on this Technical Report, please visit http:/www.sae.org/technical/standards/AMS5839C AEROSPACE MATERIAL SPECIFICATION AMS5839 REV. C Issued 1995-12 Reaffirme

5、d 2006-04 Revised 2015-12 Superseding AMS5839B Nickel Alloy, Corrosion and Heat-Resistant, Welding Wire 59Ni - 22Cr - 2.0Mo - 14W - 0.35Al (Composition similar to UNS N06231) RATIONALE AMS5839C has been updated to incorporate the standard quality requirements of AMS materials as the ordering require

6、ments for AWS specified wire and is a Five Year Review and update of this specification. 1. SCOPE 1.1 Form This specification covers a corrosion and heat-resistant nickel alloy in the form of welding wire. 1.2 Application This wire has been used typically as filler metal for gas-metal-arc or gas-tun

7、gsten-arc welding of parts fabricated from alloy of similar composition, but usage is not limited to such applications. 2. APPLICABLE DOCUMENTS The issue of the following documents in effect on the date of the purchase order forms a part of this specification to the extent specified herein. The supp

8、lier may work to a subsequent revision of a document unless a specific document issue is specified. When the referenced document has been cancelled and no superseding document has been specified, the last published issue of that document shall apply. 2.1 SAE Publications Available from SAE Internati

9、onal, 400 Commonwealth Drive, Warrendale, PA 15096-0001, Tel: 877-606-7323 (inside USA and Canada) or +1 724-776-4970 (outside USA), www.sae.org. AMS2813 Packaging and Marking of Packages of Welding Wire, Standard Method AMS2814 Packaging and Marking of Packages of Welding Wire, Premium Quality AMS2

10、816 Identification Welding Wire, Tab Marking Method SAE INTERNATIONAL AMS5839C Page 2 of 4 AMS2819 Identification, Welding Wire Direct Color Code System ARP4926 Alloy Verification and Chemical Composition Inspection of Welding Wire 2.2 AWS Publications Available from American Welding Society, 8669 N

11、W 36 Street, #130, Miami, FL 33166-6672, Tel: 1-800-443-9353 or 305-443-9353, www.aws.org. AWS A5.01 Welding Consumables Procurement of Filler Metals and Fluxes AWS A5.14 Specification for Nickel and Nickel-Alloy Bare Welding Electrodes and Rods 3. TECHNICAL REQUIREMENTS 3.1 Composition: Wire shall

12、meet the technical requirements of AWS A5.14 ERNICrWMo-1 with the following additional chemistry controls: Titanium shall be 0.10 max. 3.2 Sizes and Tolerances Wire shall be supplied in the sizes and to the tolerances shown in AWS A5.14. Smaller diameter wires when ordered shall be supplied in sizes

13、 and tolerances shown in 3.2.1. 3.2.1 Diameter Shall be as shown in Table 1. Table 1A - Sizes and diameter tolerances, inch/pound units Form Nominal Diameter Inch Tolerance Inch Plus Tolerance Inch Minus Cut Lengths Spools 0.030, 0.035, 0.045 0.007, 0.010, 0.015 0.001 0.0005 0.002 0.0005 Table 1B -

14、Sizes and diameter tolerances, SI units Form Nominal Diameter Millimeters Tolerance Millimeter Plus Tolerance Millimeter Minus Cut Lengths Spools 0.76, 0.89, 1.14 0.18, 0.25, 0.38 0.025 0.013 0.05 0.013 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsibility for Inspection The producer of wire shall supp

15、ly all samples for producers tests and shall be responsible for the performance of all required tests. Purchaser reserves the right to sample and to perform any confirmatory testing deemed necessary to ensure that the wire conforms to specified requirements. SAE INTERNATIONAL AMS5839C Page 3 of 4 4.

16、2 Classification of Tests 4.2.1 Acceptance Tests Composition (3.1), sizes and tolerances (3.2), and alloy verification (5.2) are acceptance tests and shall be performed on each heat or lot as applicable. 4.3 Sampling and Testing Shall be in accordance with AWS A5.01. 4.4 Reports The producer of wire

17、 shall furnish with each shipment a report showing the results of tests for composition of each heat, and stating that the wire conforms to the other technical requirements. This report shall include the purchase order number, heat and lot numbers, AMS5839C, nominal size, and quantity. 4.5 Resamplin

18、g and Retesting Shall be in accordance with AWS A5.01. 5. PREPARATION FOR DELIVERY 5.1 Wire shall be supplied either on spools in one continuous length for machine welding or in cut lengths for manual welding, as ordered. Wire on each spool or in each package of cut lengths shall be from the same he

19、at of steel. 5.2 Alloy Verification 5.2.1 Wire from each spool or package of cut lengths shall be alloy verified by a method acceptable to purchaser and producer. The alloy verification methods of ARP4926 are recommended. 5.2.2 An 8 inch (203 mm) length of wire shall be made accessible at both ends

20、of each spool for alloy verification. 5.3 Identification Shall be in accordance with AMS2816 unless AMS2819 or another method is specified by purchaser. 5.4 Packaging and Marking Shall be in accordance with AMS2813 unless AMS2814 or another method is specified by purchaser. 6. ACKNOWLEDGMENT A produ

21、cer shall mention this specification number and its revision letter in all quotations and when acknowledging purchase orders. 7. REJECTIONS Wire not conforming to this specification, or to modifications authorized by purchaser, will be subject to rejection. 8. NOTES 8.1 Revision Indicator A change b

22、ar (l) located in the left margin is for the convenience of the user in locating areas where technical revisions, not editorial changes, have been made to the previous issue of this document. An (R) symbol to the left of the document title indicates a complete revision of the document, including tec

23、hnical revisions. Change bars and (R) are not used in original publications, nor in documents that contain editorial changes only. SAE INTERNATIONAL AMS5839C Page 4 of 4 8.2 Terms used in AMS are clarified in ARP1917. 8.3 Dimensions and properties in inch/pound units and the Fahrenheit temperatures

24、are primary; dimensions and properties in SI units and the Celsius temperatures are shown as the approximate equivalents of the primary units and are presented only for information. 8.4 Purchase documents should specify not less than the following: AMS5839C Size and form (spools or cut lengths) of wire desired Length of cut lengths or weight of spools desired Quantity of wire desired. PREPARED BY AMS COMMITTEE “F“